Fishman VTB Manuale utente

www.ﬁshman.com

System Requirements

These instructions support installation with the

following systems:

• Fishman Acoustic Matrix Natural I &II—

between Rev. 4.0 and 6.0

• Fishman Powerjack—Rev. 2.3

• Martin Gold Plus—between Rev. 4.0 and 6.0

• Martin Active Jack—Rev. 2.3

Please note that revision numbers for each

pickup are printed on the circuit board inside

the endpin jack.

Do not attempt to install the VTB with

the discontinued Acoustic Matrix Natural

or the Acoustic Matrix Hot preamps or

similar versions of the Martin Gold Plus

systems. These systems can be identiﬁed

by the rectangular metal box that encases

the electronics.

Installation

Warning! Installation of the VTB is meant to be

performed only by a professional repairperson.

1. Locate the controls on the top of the instrument’s

shoulder, on the bass-side adjacent to the neck.

Check for interference with the internal structural

components, such as the neck block, the top braces

or the lining. When you choose a location, be aware

the VTB knobs must clear the interior lining of the

guitar case. The single-shaft control is for volume

and the dual shaft control is for bass (outer knob)

and treble (inner knob).

2. Reinforce the mounting area with a backing

strip of thin veneer glued to the inside of the

guitar. Use the included drilling template to size

the backing strip.

3. Fasten the template to locate 3⁄8” (9.5mm) holes.

VTB

INSTALLATION GUIDE

Fishman Acoustic Matrix and

Martin Gold Plus—Rev. 6.0:

1. Remove “000” jumper.

2. Thread cable assembly through barrel and solder

as indicated.

Fishman Acoustic Matrix and

Martin Gold Plus—Rev. 5.0, 5.3:

1. Remove the components from the endpin

preamp as indicated

2. Solder the new 2k resistor (supplied with your VTB)

to the preamp circuit board in place of the capacitor

3. Thread cable assembly through barrel and solder

as indicated.

Active Volume, Bass

& Treble Controls

for Fishman

Acoustic Matrix Natural I,

Acoustic Matrix Natural II

and Powerjack preamps.

www.ﬁshman.com 513-000-008 Rev B 11-06

Installation (continued)

4. Remove the endpin preamp and locate the

revision number on the circuit board. Follow the

soldering instructions that apply to the revision.

Warning: The surface-mount components on the

endpin preamp can be easily overheated with a hot

iron. Use only a low-wattage soldering iron and take

care not to overheat the components.

5. Fasten the VTB as shown:

Electrical Speciﬁcations

Typical current consumption@9Vdc: 0.85mA

Typical 9V alkaline battery life

with Acoustic Matrix preamp: 500 hours

Nominal output impedance: 1k Ohm

Recommended load impedance: 10k Ohm

and above

Signal gain (tone ﬂat, volume at maximum): 0dB (unity)

Maximum output level (1% THD@3kHz): +8dBV

Bass control (Outer shaft of dual pot):

±12dB@100Hz

Treble control (Inner shaft of dual pot):

±14dB@11kHz

Cable Color Code:

White: VTB Input Red : +9V

Black: VTB Output

Copper shield: +Ground

Because we continually make improvements to our

products, the speciﬁcations in this guide are subject

to change without notice.

1. Remove the components from the endpin

preamp as indicated

2. Solder the new 2k resistor (supplied with your

VTB) to the preamp circuit board

3. Thread cable assembly through barrel and solder

as indicated.

Fishman Acoustic Matrix and

Martin Gold Plus—Rev. 4.0:

1. Remove the “000” jumper from the endpin

preamp.

2. Thread cable assembly through barrel and solder

as indicated.

Fishman Powerjack and

Martin Active Jack—Rev. 2.3:

Indice

Altri manuali Fishman Attrezzatura musicale

Fishman

Fishman POWERJACK Manuale utente

Fishman

Fishman M-200 PRO MANDOLIN PICKUP Manuale utente

Fishman

Fishman M-200 PROFESSIONAL MANDOLIN PICKUP Manuale utente

Fishman

Fishman ELLIPSE BLEND - Dimensioni

Fishman

Fishman RARE EARTH - Manuale utente

Fishman

Fishman ELLIPSE BLEND - Manuale utente

Fishman

Fishman RARE EARTH - Manuale utente

Fishman

Fishman ELLIPSE VT - Manuale utente

Fishman

Fishman SWITCHJACK - ANNEXE 827 Manuale utente

Fishman

Fishman NASHVILLE PICKUP Manuale utente

Fishman

Fishman TriplePlay Guida all'installazione

Fishman

Fishman NEO-D Manuale utente

Fishman

Fishman NEO-D - ANNEXE 282 Manuale utente

Fishman

Fishman ELLIPSE VT - Manuale utente

Fishman

Fishman Powerbridge VS-50P Manuale utente

Fishman

Fishman TSV POWERBRIDGE - ROUTING Manuale utente

Fishman

Fishman VTB - DRILLING Manuale utente

Fishman

Fishman MATRIX INFINITY - Manuale utente

Fishman

Fishman V-100 VIOLIN Manuale utente

Fishman

Fishman ELLIPSE AURA - Manuale utente

Fishman

Fishman TUNE-O-MATIC POWERBRIDGE - ROUTING Manuale utente

Fishman

Fishman VS-50P POWERBRIDGE - ROUTING Manuale utente

Fishman

Fishman VT POWERBRIDGE - ROUTING Manuale utente

Fishman

Fishman MODEL VMV Manuale utente

Manuali Attrezzatura musicale popolari di altre marche

DAPAudio

DAPAudio IPS-PT Manuale utente

Dynacord

Dynacord DPM 8016 Manuale utente

Subdecay

Subdecay Starlight Flanger Manuale utente

Moen

Moen GEC8 Live Manuale utente

Fender

Fender 1 Manuale utente

Yamaha

Yamaha MLC-16 Manuale utente

Sonuscore

Sonuscore TIME TEXTURES Manuale utente

flight of harmony

flight of harmony V'Amp Manuale utente

NANO

NANO PERFORMANCE MIXER Manuale utente

Tascam

Tascam CD-GT2 Manuale utente

BHI

BHI NEIM 1031 MKII Manuale utente

Befaco

Befaco KICKALL Manuale utente

Paia

Paia 9720 Guida

limex

limex ALPIN MASTER 128 Manuale utente

nord

nord Electro 3 Manuale utente

Joemeek

Joemeek sixQ2 Manuale utente

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Manuale utente

Furutech

Furutech ADL GT40 Guida all'installazione