Flair Espresso 58 Manuale
Flair 58
Preheat System Safety &
Instructions Guide
Flair Espresso
28 Hammond Street, Suite B
Irvine, CA 92618
www.airespresso.com - service@airespresso.com
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed. This includes the following:
• Read all instructions.
• Do not touch hot surfaces. Use handles and silicone pads.
• To protect against re, electric shock and injury to persons, do not immerse cord, plugs, base or brew head in water or other liquid,
regardless if the cords are connected or plugged into an electrical socket.
• Never leave this appliance unattended while in use. Keep this appliance away from children’s reach. Close supervision is necessary when
this appliance is used near children to ensure that they do not play with this appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking o parts and before cleaning this
appliance.
• Do not operate this appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner.
Email our customer service team for examination, repair or adjustment.
• Do not let cord hang over edge of table, or counter, or touch hot surfaces.
• A power-supply cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
• Electric brew head must be used while installed on the portalter base of the Flair 58 only. Before use, ensure the Flair 58 is on a at and
even surface. Do not place on or near a hot gas or electric burner, or in a heated oven, or on the top of other electric appliances.
• Always attach plug to appliance rst, then plug cord into the wall outlet.
• To disconnect, push and hold main button until lights turn o, then remove plug from wall outlet.
• Do not use appliance for any purpose other than intended use.
• To avoid circuit overload, do not operate another high wattage appliance on the same circuit.
• Do not use the brew head to heat anything other than water. Do not overll. If the cylinder is overlled, boiling water may be ejected.
• Do not insert any object into slots or holes of the brew head.
• If the supplied cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualied person in order to
avoid hazard.
• Do not use a longer detachable power-supply cord or extension cord.
• Never move the brew head or entire Flair 58 together while the unit is in use.
• To avoid burns and risk of personal injury, use extreme caution when dealing with hot water.
• Do not use the brew head if your hands are wet.
• Position the brew head properly on the portalter base before connecting or switching on.
• Use the brew head and Flair 58 only with delivered power equipment. Do not use any other power or electrical equipment that was not
delivered with your Flair 58. Use only the original, delivered Flair 58 power and electrical equipment.
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com Page 1
WARNING: The appliance is very hot during use. Do not touch the surface of the brew head while in use or heated. Danger
of burns!
WARNING: Never leave the brew head unattended while preheating water, especially if there are children nearby.
WARNING: Do not immerse or wash the entire brew head in water or any other liquid. This may cause electric shock or
damage the appliance.
WARNING: Be careful when handling hot water. Danger of scalding!
TO PREVENT SCALDING: - Never move the Flair 58 while the preheat system is on and water is inside the brew head - Water
can remain hot for a long time after preheating and can present a scalding hazard - Keep the Flair 58 and the brew head
away from the edge of the work surface and out of the reach of children. Do not remove the brew head until it has fully
cooled down.
Save these instructions.
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com
CONTENTS OF THIS MANUAL
• Flair 58 Preheat System Introduction
• Flair 58 Preheat System Parts
• Flair 58 Preheat System Setup
• Flair 58 Preheat System Use Instructions
• Flair 58 Preheat System Cleaning Instructions
• Flair 58 Warranty
Introduction
Your Flair 58 comes equipped with a preheat system on the brewing head that allows users to maintain a constant preheat during and in-between shots
of espresso. This Preheat System has three temperature tiers:
• Low Heat – roughly 85° C (185° F)
• Medium Heat – roughly 90° C (194° F)
• High Heat – roughly 95° C (203° F)
These temperature tiers are meant to loosely correspond to dierent roast levels: light, medium and dark but can be used as desired to dial-in your shot
of espresso for the best taste experience. Your Flair 58 Preheat System is not meant to boil your water, and cannot be used for anything other than its
intention of maintaining a constant temperature on your brew heat for enhanced thermal control. In all cases, the initial temperature of your brew water
should be managed with your kettle, prior to pouring into your Flair 58.
Further instructions can be found in our Quick Start Guide, provided with your Flair 58, or online at: https://airespresso.com/learn. There you will nd
video guides as well as downloads that will aid you in any troubleshooting. As always, if you do experience any issues, please reach out to our customer
support via the email address at the bottom of each page.
Page 2
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com
Preheat System Parts
1. Brew Head with four-pin (male) connector
2. Power Supply with a single-pin (female)
connector
3. Preheat Controller with four-pin (female)
and single-pin (male) connectors
4. Power Supply Extension Cord
1
3
2
4
Page 3
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com Page 4
Preheat System Setup
Setting up your Preheat system is a simple process of making the appropriate connections so power can be supplied to the brewing head.
1. Unpack and remove any and all protective plastic from parts received in your Flair 58 packing box
2. Ensure you have each of the four Preheat System parts as described, and shown, in the page above
3. Follow instructions to put together your Flair 58 base and lever, with the included screws
4. Add your Flair 58 Brew Head onto the portalter base and lock into place by turning counter-clockwise (when locked, the Flair
58 logo should be facing front)
5. Connect the four-pin (male) connector on the brew head with the four-pin (female) connector on the Preheat Controller, by rst aligning
the tabs using the small arrows on each piece, and screw lock into place
6. Connect the single-pin (male) connector on the Controller to the single-pin (female) connector on the power supply
WARNING: Always ensure the single pin connectors are UNPLUGGED before connecting or disconnecting the four-pin connectors.
7. Ensure the Power Supply Extension Cord is plugged into the Power Supply
8. Plug Power Supply into outlet on the wall
324
25
26
27
28
ALIGN
SMALL
ARROWS
WARNING:
Always
UNPLUG
#6 BEFORE
Connecting or
Disconnecting
#5
25
26
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com Page 5
Preheat System Use Instructions
Before using the Preheat System it is important for each user to determine the level of preheat temperature they’d like: Low, Medium or High.
In addition, it is important to remember that the Preheat System is meant to maintain the temperature of the system while adding heated brew water.
It is not intended to be used as a method to heat your brew water. The heating and management of your brew water’s temperature should always be
managed with your kettle.
The Controller has one singular button with three green indicator lights. These lights have three states each: o, blinking and solid on. The indicators of
each of these states is listed below:
• OFF – This temperature level is o or inactive
• BLINKING – Indicates a heating stage
• SOLID ON – Indicates that the desired temperature has been reached
The three lights correspond to the dierent preheat temperature that has been selected: Low, Medium and High, from left to right across the controller.
Directions for selecting and preheating to each level are below.
Once a temperature setting has been reached, the Preheat System will maintain that setting until turned o. In order to reduce the level of your preheat
- from high to medium, or medium to low - simply use short presses of the button to quickly cycle through the various heat settings.
Flair 58 Preheat System Safety and Instruction Guide - service@airespresso.com Page 6
Preheat System Cleaning
Your Flair 58 Preheat system and brew head, if maintained correctly, will not require signicant maintenance. For best results, all cleanings should be
completed while the brew head is axed onto the portalter base of the Flair 58.
Please Note: The Preheat System must be turned o and allowed ample time (at least 15 minutes) to cool before any
cleaning is attempted. Failure to allow the system to cool adequately can result in burns.
Cleaning should be completed with cool water only, and a clean damp cloth. No soaps or detergents are needed and may damage your Flair 58 and your
Preheat System. Using soap can also impact the avor of your espresso.
WARNING: Never immerse, submerge, or fully rinse the components of the Preheat System in water. Also ensure that the
open connector points, both the four-pin and single-pin, male and female, are kept dry at all times. Failure to do this can
damage the system and will void the warranty.
To clean your Preheat System, follow these simple steps:
1. Remove plunger by pulling it out with stem while brewing cylinder is installed on base
2. Use damp cloth to wipe the inside and bottom of the brew head. Also wipe the plunger.
3. For more thorough cleaning, place a cup beneath your Flair 58 and ush with cool water before wiping. This can be repeated
multiple times to remove any coee residue
Flair 58 & Preheat System Warranty
The Flair 58 Press Stand is warranted against functional defects for ten (10) years, from date of purchase, when used in accordance with all operating
and safety instructions. The Flair 58 metal brew head components are warranted for ve (5) years, from the date of purchase, when used in accordance
with all operating and safety instructions. The electrical components of the Preheat System of the Flair 58 are warranted against functional defects for two
(2) years from the purchase date, again when used in accordance with all operating and safety instructions. Parts that are more subject to normal wear
and tear, such as O-rings, Silicone Sleeves, Piston, Tamper, Portalter and Filter Basket are warranted against defects in material, design or workmanship
for six (6) months from the purchase date, although these items are expected to last beyond the warranty.
Proof of purchase is required to validate the warranty period.
The warranty applies only when the product and parts are used in accordance with all operating instructions. The warranty does not include shipping
costs. The warranty becomes void if we deem that the product or parts were modied, abused or improperly used, damaged by accident or neglect, or if
any parts are improperly installed.
Intact Idea makes no other warranties, express or implied, and specically excludes warranties of merchantability and tness for a particular purpose.
Intact Idea’s liability under this warranty shall be limited to repair or replacement of the defective part(s), whichever may apply. Intact Idea shall not be
responsible for any damages or personal injuries, whether incidental or consequential, or claims for such damages based on any legal theory, which
may occur while using this product. This warranty gives you specic legal rights, and you may also have other rights which may vary from state to state
and country to country.
Indice
Altri manuali Flair Espresso Macchina per il caffè
