Flash Media FMPD40N2 Manuale utente

User’sManual

CONTENTS:

Chapter I Introduction to outline and interface------------------------------------------3

1.1 Introduction to FMPD40N2---------------------------------------------------------------------------------------3

1.2 Introduction to FMPD42N2---------------------------------------------------------------------------------------3

1.3 Introduction to FMPD46N2 --------------------------------------------------------------------------------------3

1.4 Introduction to interface-------------------------------------------------------------------------------------------4

Chapter II Connecting ---------------------------------------------------------------------------------5

2.1Control Ting LCD Wall s through RS232-----------------------------------------------------------------------5

2.2 DVI Signal ------------------------------------------------------------------------------------------------------------5

2.3 Video signal ----------------------------------------------------------------------------------------------------------5

2.4 RGB/HV signal ------------------------------------------------------------------------------------------------------6

Chapter III Remote Control and Signal Input --------------------------------------7

3.1 Introduction to Remote Control-------------------- -------------------------------------------------------------7

3.2 Instruction to signal input selection: ---------------------------------------------------------------------------7

3.3 Menu Introduction-:-------------------------------------------------------------------------------------------------8

User’sManual

Chapter I Introduction to outline and interface

1.1 Introduction to FMPD40N2:

1.2 Introduction to FMPD42N2:

1.3 Introduction to M20S1:

Front: Left: Back: Right:

1.3 Introduction to FMPD46N2:

User’sManual

1.4 Introduction to Interface:

A．ACIN:Connect with power cord. H、OSD interface

B. RS232 INPUT / RS232 OUTPUT

D. BNC/YPbPr IN: input connectors for component

signals

BNC/YPbPr OUT: output connectors for component

signals

BNC/RGB/HV IN: (R, G, B, H, V) input connectors for video signals from

computer

BNC/RGB/HV OUT: (R, G, B, H, V) output connectors for video signals

from computer

VIDEO1 IN/VIDEO1 OUT Input/Output connectors for video signals

RCA/VIDEO2 Input connect for video signal

DIN 4 PIN/S-Video Input connector for S-video

VGA (D-SUB) IN: (input connectors for video signals from computer)

D-Sub cable (15 pin D-Sub) - PC model ( Analogue Signal)

DVI (DVI–D) IN: (input connectors for video signals from computer ) DVI-D

model (Digital Signal)

AUDIO IN 1：DVD/HD, VIDEO1 (RCA)

AUDIO IN 2：VIDEO2 (RCA), S-VIDEO (RCA)

AUDIO IN 3：STEREO Mini Jack VGA RGB HV/ DVI

AUDIN OUT：STEREO Mini Jack

User’sManual

Chapter II Connecting

2.1 RS232 Control:

Ting LCD Wall s can be controlled by computer through RS232 cable. There are two RS232 connectors on the

Ting LCD Wall . (One for signals input, the other for signals output). Every Ting LCD Wall needs a separate ID

number to realize management through RS232.

2.2 DVI Signal

Connect the Ting LCD Wall and computer through DVI-D cable, and switch the signals input to DVI in menu.

Use AUDIO IN3 connector for audio input, and AUDIO OUT for audio output.

2.3 Video signal

Video2 and S-video signal

Connect DVD and Ting LCD Wall through video cable by Video2 or S-VIDEO connectors. Switch signal input of

Ting LCD Wall to Video2 or S-VIDEO.

Use AUDIO IN2 connector for audio input, and AUDIO OUT for audio output.

User’sManual

YPbPr and Video1 signal

1. Connect signal source Video1 signal or HD signal and Ting LCD Wall through BNC cable.

2. Use YPbPr OUT or Video1 OUT connector to send signals to a second Ting LCD Wall .

3. Use AUDIO IN1 as audio input, and AUDIO OUT as audio output.

2.4 RGB/HV signal

1. Use RGB signal cable with D-SUB connector (15 PIN) to connect Ting LCD Wall and computer. Switch signal

input to VGA.

2. Use RGB/HV cable to connect Ting LCD Wall through BNC/RGB/HV IN and computer. Switch signal input to

VGA2.

3. Use RGBHV/OUT and a cable to send signal to a second Ting LCD Wall .

4. Use AUDIO IN3 as audio input connector and AUDIO OUT as audio output connector.

User’sManual

Chapter III Remote Control and Signal Input

3.1 Introduction to Remote Control:

3.2 Instruction to signals input:

Press GOTO button to enter signals input list and use navigation buttons to make a choice.

1. VGA: analogue signal from computer

2. DVI：digital signal from computer

3. AV : VIDEO signal input 1

4. AV2: VIDEO signal input 2

5. S-VIDEO: S-Video signal input

6. YPbPr: Components signal input

7. VGA2: BNC/RGB HV signal input

GOTO:

Select signal input

Power: Press this button

to turn On / Off monitor

Navigation Buttons:

Press these buttons to select

preference and MENU fo

confirmation.

User’sManual

3.3 Menu Introduction:

■ PICTURE：

Press “Menu” button, then the following screen shows up. Use navigation buttons to adjust parameters.

1）CONTRAST:

Use navigation buttons to adjust values of contrast.

2）BRIGHTNESS: Use navigation buttons to adjust values of brightness.

3）SATURATION: Use navigation buttons to adjust values of saturation.

4）SHARPNESS: Use navigation buttons to adjust values of sharpness.

5）COLOR TEMP: Use navigation buttons to change modes of color temperature: Standard / Warm / Cold / User.

■SOUND:

1）BASS, TREBLE, BALANCE: Use navigation buttons to adjust notes and balance of sound.

2）SOUND MODE: Use navigation buttons to change sound modes: STANDARD, NEWS, MUSIC

3）AVC, LOUDNESS, SUPERBASS, SOUND EFFECT: Use navigation buttons to make proper selection.

User’sManual

■ADVANCE

1）CLOCKER：Real time set

2）ON TIME：Time to turn on the unit

3）OFF TIME：Time to turn off the unit

4）SLEEP TIME：ON/OFF sleep time (when ON TIME and OFF TIME are not activated)

5）TOTAL X (Number of horizontal screens): Setting the number of landscape displays. Adjust the number of

“X” by clicking “↑”and “↓” buttons

6）TOTAL Y (Number of vertical screens): Setting the number of portrait displays. Adjust the number of “Y” by

clicking “↑”and “↓” buttons.

7）CURRENT X Setting the abscissa of the unit

8）CURRENT Y Setting the ordinate of the unit

Sketch for tilling video wall : 3 x 3

9）TEMPERATURE: Actual temperature for Ting LCD Wall

10）FAN ACTIVE: Users can set a temperature value to activate fans. When the temperature is higher than the

value the fan will turn on automatically, otherwise, it will turn off automatically.

Note：M20S1 and M19S1 don't have temperature or fan active functions.

User’sManual

■OSD:

1) OSD LANGUAGE: CHINESE or ENGLISH.

2) OSD H-POSITION/ OSD V-POSITION: set the horizontal/vertical position of the menu

3) OSD DURATION: 5SEC, 10SEC, 15SEC, 30SEC, 45SEC, 60SEC.

4) MEMORY RECALL: Return to default setting.

5) LEFT EDGE: 0-30

UPEDGE: 0-30

RIGHT EDGE: 0-50

DOWN EDGE: 0-50

The Ting LCD Wall s are able to eliminate stagger of display.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione