Flash EVENT Series Manuale utente
7X40W BIG EYE PRO
SERIES: EVENT
User Manual
Instrukcja Obsługi
Art No F7100555
CONTENTS
INTRODUCTION 3
SAFETY INFORMATION 3
PRODUCT INFORMATION 4
INSTALLATION 4
CONNECTION 5
DMX CHART 7
WARNING! The Led Moving Head (LMH) has a powerful pan and lt mo-
tor. The torque reacon when the head is panned suddenly can cause the
base to move if the xture is standing unsecured on a surface. Do not apply
power to the LMH unless the baase is securely fastened to a surface or to
rigging hardware.
WARNING! Use 2 clamps to rig the xture. Do not hang the xture from
only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners
are locked only when turned a full 900 clockwise.
WARNING! When clamping the xture to a truss or other structure at
any other angle than with the yoke hanging vercally downwards, use two
clamps of half-coupler type. Do not use any type of clamp that does not
completely encircle the structure when fastened.
WARNING! Posion or shade the head so that the front lens will not be
exposed to sunlight or any other strong light source from any angle - even
for a few seconds. See Figure 1. The LMH lens can focused the sun’s rays,
creang a potenal re hazard and causing damage.
IMPORTANT! Do not point strong light output from other xtures at the
LMH, as intense illuminaon can damaged the display.
Figure 1.
2
EN
PL
Pages: 2-14
Strony: 14-25
INTRODUCTION
SAFETY INFORMATION
THANK YOU FOR PURCHASING 7X40W BIG EYE PRO. FOR SAFETY
REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CA-
REFULLY READ THE INSTRUCTIONS.
Please keep this User Manual
for future consultaon. If you sell
the xture to another user, be sure
that they also receive this instruc-
on booklet.
Unpack and check carefully the-
re is no transportaon damage be-
fore using the xture.
Before operang, ensure that
the voltage and frequency of po-
wer supply match the power
requirements of the xture.
It’s important to ground the
yellow/green conductor to earth
in order to avoid electric shock.
Disconnect main power before
servicing and maintenance.
Use safety chain when xes this
xture. Don’t handle the xture by
taking its head only, but always by
taking its base.
Maximum ambient temperature
is: 40°C Don’t operate it where the
temperature is higher than this.
In the event of serious ope-
rating problem, stop using the
fixture immediately. Never try
to repair the fixture by your-
self.
Repairs carried out by unskil-
led people can lead to damage
or malfunction. Please contact
the nearest authorized techni-
cal assistance center. Always
use the same type spare parts.
Do not connect the device
to any dimmer pack.
Do not touch any wire during
operation and there might be a
hazard of electric shock.
To prevent or reduce the risk
of electrical shock or fire, do
not expose the fixture to rain
or moisture.
The housing must be repla-
ced if they are visibly damaged.
Do not look directly at the li-
ght spot while the fixture is on.
3
PRODUCT INFORMATION
INSTALATION
Light Source:
LED RGBW 7x40W RGBW
Power consumpon: 350W
Power supply voltage:
100-240V, 50/60Hz AC
PAN range: 540°
TILT range: 270°
Beam angle (min/max):
3,5°-55°
Features: CTO, Zoom, Macro
Colors,
Variable Strobo
Operang modes: DMX, Auto,
Sound-controlled, Master, Slave,
RDM
DMX channel mode:
23 /35/5 1
IP Rang: IP20
Housing made: ABS
Cooling: Acve
AC IN/OUT: TrueCon
3-Pin XLR DMX Input/Output
Net Weight: 9,8 kg
Dimensions:
H(41)xW(31)xD(23) cm
The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is rmly xed to avoid vibraon and slipping while
operang. Always ensure that the structure to which you are aaching
the unit is secure and is able to support a weight of 10 mes of the
unit’s weight. Also always use a safety cable that can hold 12 mes of
the weight of the unit when installing the xture. The equipment must
be xed by professionals. And it must be xed at a place where is out of
the touch of people and has no one pass by or under it.
Regardless of the rigging opon ypu chose for our xture, always be
sure to secure your xture with safety cable. The xture provides a
builit-in rigging point for a safety cable on the hanging bracket as illu-
strated above. Be sure to only use the designated rigging point for the
safety cable and never secure a safety cable to a carrying handle.
4
5
CONNECTION
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): TrueCon socket
The connecon is performed using cable with
XLR-female -> XLR-Male plugs.
1
3
22
SHIELD
SIGNAL (+)
SIGNAL (-)
3
1
FEMALE
XLR
MALE
XLR
1
SHIELD
SIGNAL (+)
SIGNAL (-)
FEMALE
XLR
MALE
XLR
2
3
4
5
1
2
3
45
CAUTION! At the last xture, the
DMX signal has to be terminated
with a terminator. Solder a 120Ω
resistor between signal (-) and si-
gnal (+) into a XLR plug and plug
it in the DMX output of the last
xture.
3-PIN XLR
5-PIN XLR
Diagram of connecon of devices by DMX cable.
IMPORTANT! The maximum number of devices connected
in series via power cable is 3 pcs.
DMX
Controller DMX 512 DMX 512
Using lamp, the change rate of power voltage should be within ±10%,
if the voltage is too high, it will shorten the light’s life; if it’s not enough,
the lamp will be dark. Please restart it aer turning o light for 20 mi-
nutes unl full-cooling. Frequent switching will reduce the life span of
lamps and bulbs; intermient using will improve the life of bulbs and
lamps.
Input Voltage Amperage Frequency Total Power
230[V] AC 1.13[A] 50[Hz] 350[W]
Voltage Specycaon.
6
The connecon is performed using power cable with TrueCON con-
nector (included). The device must be operated by qualied personnel.
CAUTION! In the case of cable damage do not aempt to repair. Repla-
cement or repair can be made only on the manufacturer or by a person
with appropriate permissions
1 . DMX ADDRES --- ENTER --- 001-512
2 . SET --- ENTER
RUN MODE --- ENTER --- DMX / AUTO 1 / AUTO 2 / SOUND
CHANELL MODE --- 23CH / 35CH / 51CH
PAN INWERT --- ENTER --- ON / OFF
TILT INWERT --- ENTER --- ON / OFF
HALL CRCT --- ENTER --- ON / OFF
ENCODER --- ENTER --- ON / OFF
SIGNAL KEEP --- ENTER --- ON / OFF
SCREEN SAVER --- ENTER --- AUTO / ON / OFF
UPDATE SLAVE --- ENTER --- ON / OFF
LANGUAGE ---- ENTER ---- ENG / CH
LOAD DEFAULT --- ENTER --- OK / CANCEL
3 . MANUAL --- ENTER ---- POSSIBILITY OF MANUAL SETTINGS OF EACH
PRE-SELECTED MODES 23CH / 35CH / 51CH
4 . CALIBRACJON --- ENTER --- CALIBRATION OF THE DEVICE FUNCTIONS
5 . RESET --- ENTER --- RESET EFFECT / RESET SCAN / RESET ALL
6. NOTE --- ENTER --- SYSTEM INFO
Manual Menu
7
DMX CHART
1PAN 0-255
2 PAN FINE 0-255
3 TILT 0-255
4 TILT FINE 0-255
5PAN /TILT SPEED 0-255
6 ZOOM 0-255
7ZOOM ROTATION 0-255
8DIMMER 0-255
9STROBO 005-103 STROBO SLOW TO FAST
104-107 LIGHT ON
108-207 PULS STROBO SLOW TO FAST
208-212 LIGHT ON
213-251 RANDOM STROBO SLOW TO FAST
252-255 LIGHT ON
10 RED
11 GREEN
12 BLUE
13 WHITE
14 CTO
15 MACRO
16 STATIC EFFECT 000-029 LIGHT ON
030-044 EFFECT 1
045-059 EFFECT 2
060-074 EFFECT 3
075-089 EFFECT 4
……
120-134 EFFECT 7
STATIC EFFECT MACRO COL. 135-149 EFFECT 8
150-164 EFFECT 9
165-179 EFFECT 10
180-209 EFFECT 11
23 CH
8
210-224 EFFECT 12
225-239 EFFECT 13
240-254 EFFECT 14
……
255 EFFECT 15
17 DYNAMIC EFFECT 000-008 LIGHT ON
009-014 EFFECT 1
015-019 EFFECT 2
020-029 EFFECT 3
030-034 EFFECT 4
035-039 EFFECT 5
……
080-084 EFFECT 13
085-089 EMPTY
090-094 EFFECT 14
……
120-124 120-124 EFFECT 20
DYNAMIC EFFECT MACRO COL. 125-129 EFFECT 21
130-134 EFFECT 22
135-139 EFFECT 23
140-144 EFFECT 24
……
200-204 EFFECT 36
205-255 EFECT 37
18 DYNAMIC SPEED
19 BACKGR. RED
20 BACKGR. GREEN
21 BACKGR. BLUE
22 BACKGR. WHITE
23 RESET
9
1 RED 0-255
2 RED FINE 0-255
3 GREEN 0-255
4 GREEN FINE 0-255
5 BLUE 0-255
6BLUE FINE 0-255
7 WHITE 0-255
8WHITE FINE 0-255
9CTO 0-255
10 MACRO 0-255
11 STROBO 005-103 STROBO SLOW TO FAST
104-107 LIGHT ON
108-207 PULS STROBO SLOW TO FAST
208-212 LIGHT ON
213-251 RANDOM STROBO SLOW TO FAST
252-255 LIGHT ON
12 DIMMER 0-255
13 DIMMER FINE 0-255
14 PAN 0-255
15 PAN FINE 0-255
16 TILT 0-255
17 TILT FINE 0-255
18 FUNCTION 0-255
19 RESET 0-255
20 ZOOM 0-255
21 ZOOM ROTATION 0-255
22 SHAPE SELECTION 0-255
23 SHAPE SPEED 0-255
24 SHAPE FADE 0-255
25 SHAPE RED 0-255
26 SHAPE GREEN 0-255
27 SHAPE BLUE 0-255
28 SHAPE WHITE 0-255
35 CH
10
29 SHAPE DIMMER 0-255
30 BACKGR. DIMMER 0-255
31 SHAPE TRANSITION 0-255
32 SHAPE OFF SET 0-255
33 FOREGR. STROBE 0-255
34 BACKGR. STROBE 0-255
35 BACKGR. SELECTION 0-255
Altri manuali per EVENT Series
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Flash Attrezzatura di illuminazione
Flash
Flash F7100330 Manuale utente
Flash
Flash FL-232 BEAM 7R Manuale utente
Flash
Flash LIGHT BOX MOON 2 Manuale utente
Flash
Flash FL-330 BEAM 15R Manuale utente
Flash
Flash HYBRID 10R Manuale utente
Flash
Flash F7200204 Manuale utente
Flash
Flash F7100303 Manuale utente
Flash
Flash F7100327 Manuale utente
Flash
Flash F7300231 Manuale utente
Flash
Flash F7200203 Manuale utente
Flash
Flash FL-233 BEAM Manuale utente
Flash
Flash LED WASHER RGB IP34 ver.II Manuale utente
Flash
Flash F7100320 Manuale utente
Flash
Flash F7300254 Manuale utente
Flash
Flash FOLLOW SPOT 350W Manuale utente
Flash
Flash F7100070 Manuale utente
Flash
Flash F7100337 Manuale utente
Flash
Flash LOGO Manuale utente
Flash
Flash F7100525 Manuale utente
Flash
Flash 19x40W PRO Manuale utente
