Flavel Raglan KBFC**MN Manuale utente

Raglan

DECORATIVE COAL EFFECT BALA CED FLUE

GAS FIRE

User Instructions

These instructions should be read by the user before operating the

appliance and retained for future reference

Model o. KBFC**M is only for use on atural Gas (G20) at a supply

pressure of 20 mbar in G.B. / I.E.

B: ** denotes colour variants

I STALLATIO I FORMATIO

CO DITIO S OF I STALLATIO

It is the law that all gas appliances are installed only by a competent (e.g. CORGI

Registered) Installer in G.B. in accordance with the installation instructions and the

Gas Safety (Installation and Use) Regulations 1998 as amended. Failure to install

appliances correctly could lead to prosecution. It is in your own interest and that

of safety to comply with the law.

The fire may be fitted below a combustible shelf provided that the shelf is at least

200mm above the top of the appliance and the depth of the shelf does not exceed

150mm.

The fire may be installed below combustible shelves, which exceed 150mm deep

providing that the clearance above the fire is increased by 15mm for each 25mm

of additional overhang in excess of 150mm.

If this appliance is fitted directly on to a wall without the use of a fireplace or sur-

round, soft wall coverings such as wallpaper, blown vinyl etc. could be affected by

the heat and may discolour or scorch. This should be considered when installing

or decorating.

The odel number of this appliance is KBFC** N and it is manufactured by:-

BF Europe Ltd.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

NB ** denotes colour variants

ABOUT YOUR EW RAGLA FIRE

The Flavel Raglan is a decorative fuel effect balanced flue gas fire incorporates a

unique and highly developed fuel bed which gives the realism of a loose coal

layout combined with realistic flames and glow. The use of durable hard ceramic

material in the construction of the fuelbed components ensures long and trouble

free operation.

When first using the new fire a slight smell may be noticed. This is due to small

deposits of oil on the firebox, but will soon disappear

Please take the time to fully read these instructions as you will then be able to

obtain the most effective and safe operation of your fire.

DO OT U DER A Y CIRCUMSTA CES ATTEMPT TO USE THIS APPLIA CE

IF THE GLASS PA EL IS BROKE OR HAS BEE REMOVED.

IMPORTA T SAFETY I FORMATIO

WAR I G : This appliance has a naked flame and as with all heating

appliances a fireguard should be used for the protection of children, the

elderly and infirm. Fireguards should conform to BS 6539 (1984) (Fireguards

for use with solid fuel appliances).

Servicing should be carried out annually by a competent person such as a

CORGI registered engineer. It is a condition of Flavel Fires guarantee

schemes that this is carried out by a competent person i.e a CORGI

registered Engineer in accordance with these servicing notes

The service should include visually checking the appliance flue terminal for

obstructions.

The condition of the one piece fuelbed should be checked and if necessary the

whole unit should be replaced with a genuine replacement set.

After any servicing work a gas soundness check and spillage test must

always be carried out.

Any debris or deposits should be removed from the fuel bed from time to time.

This may be carried out by referring to the cleaning section as described later in

this book.

Only the fuelbed as supplied must be used and complete and genuine replace-

ments must be used.

Always keep furniture and combustible materials well clear of the fire and never

dry clothing or items either on or near to the fire. Never use aerosols or

flammable cleaning products near to the fire when it is in use.

The fuel bed remains hot for a considerable period after use and sufficient

time should be allowed for the fire to cool before cleaning etc.

The fire must only be operated with the fender and ash pan cover supplied and in

position.

OPERATI G THE FIRE

The controls are located behind the brass cover below the fender. The controls,

comprise a control valve to adjust the gas flow and a push button piezo igniter. To

light the fire proceed as follows:-

1) Depress the control knob and turn anti-clockwise to the position marked pilot.

Hold in the control knob for a few seconds to allow the gas to reach the pilot.

2) Continue to hold-in the control knob and press the igniter button. If the pilot

does not light, continue to press the igniter button until ignition occurs. The

pilot flame can be seen by looking across the front line of the burner. When

the pilot has lit, continue to hold the control knob in for 5-10 seconds to allow

the thermocouple to heat up, if the pilot goes out when the control knob is

released, repeat the lighting sequence.

After lighting, turn the control knob in the anti-clockwise direction to the high

position and the main burner will light. To gain the most efficient

performance, it is recommended that the control is left in the high position for

5 to 10 minutes

3) The gas control can be turned clockwise from the maximum position to give

the desired heat output.

4) To turn the fire off push in and turn the control valve fully clockwise in to the

off position, the burner and pilot will go out.

WHE TUR I G THE FIRE “OFF” PLEASE E SURE THAT THE CO TROL

VALVE IS TUR ED TO THE “OFF” POSITIO A D THE PILOT FLAME IS

EXTI GUISHED. DO OT LEAVE THE PILOT FLAME O LY LIT.

WAR I G : If the fire goes out for any reason or is turned off and it is neces-

sary to re-light the fire it is important to allow the fire to cool for a full 5 min-

utes before attempting to re-light it.

OTE : THIS APPLIA CE IS DESIG ED TO WORK SAFELY A D

EFFECTIVELY DURI G ADVERSE WEATHER CO DITIO S. HOWEVER,

DURI G SUCH TIMES FLAME DISTURBA CE MAY BE OTICED. THIS IS

ORMAL A D DOES OT EFFECT OR IMPAIR THE SAFETY OF THE

APPLIA CE.

CLEA I G

WAR I G : Before attempting any cleaning operation ensure that the fire has

been allowed to fully cool.

CLEA I G THE TRIM A D PAI TED METAL PARTS

The trim fitted to this fire may be laquered and will therefore retain it’s looks for

the life of the fire. The ashpan and fret (if supplied with the fire) are also laquered

and may be cleaned in the same way. The brass trim is best cleaned by removing

it from the fire and placing it face up on a flat surface. The trim is easily replaced

by repositioning it on the fire and pushing it back onto the magnets. After using

any metal polish or cleaners the fire should not be used for 15 minutes or so to

allow any cleaning solvents to evaporate.

Black, Stainless steel or Black painted metal parts should be gently cleaned with a

damp cloth. Abrasive cleaners, chemical cleaning agents or any type of pol-

ish must never be used as damage to the paint may result.

CLEA I G THE FUEL BED

We do not recommend cleaning the fuelbed other than at annual service intervals.

If carbon or soot accumulates on the one piece fuelbed, this should be removed

by carefully brushing the fuelbed using a soft brush. For instructions on how to

remove the glass panel please see page 7. The one piece fuelbed is made

from a form of refractory ceramic fibre and should be handled carefully to

avoid generating dust, as this may be harmful if inhaled. As with some

fibrous materials, handling fibrous materials without gloves could cause

skin irritation.

The fuelbed should never be washed or exposed to any cleaning agents or

water.

Any damaged parts must be replaced by contacting your dealer or telephoning

BF Europe Ltd on the number stated on the rear cover of this book. The fuelbed

must only be replaced with a genuine replacement and the fire must never be run

with a different fuelbed fitted.

The fuelbed must be carefully reassembled as stated in the following section.

CLEA I G THE GLASS PA EL

To clean the glass panel, first ensure that the fire is cool, please note that the

glass panel will remain hot for a considerable period when the fire has been

switched off.

To remove the glass panel, follow the instructions over page for removal and

re-fitting.

The glass panel should be cleaned gently with a soft damp cloth and glass

cleaner.

DO OT U DER A Y CIRCUMSTA CES ATTEMPT TO CLEA THE GLASS

PA EL WHE THE APPLIA CE IS RU I G.

FOLLOWING CLEANING OF THE GLASS PANEL, ALWAYS ENSURE THAT THE

ALLEN KEY IS RE OVED FRO THE ALLEN BOLTS AND REPLACED INTO

ITS LOCATION AT THE BOTTO LEFT HAND SIDE OF THE FIREBOX.

REMOVI G & REFITTI G OF THE GLASS FRAME.

Fig. 1

a) Remove the brass trim, ashpan cover and fret from the firebox.

b) Remove the pilot heat shield, which is held in place at each end by

1 screw.

c) Remove the top infill panel by sliding it upwards out of the clips.

(See Fig. 1)

d) Obtain the allen key which is located at the bottom left hand side if

the firebox.

e) Loosen each allen bolt a small amount at a time to prevent damage

to the glass panel. (See Fig. 1) When all the allen bolts have been

removed, lift away the glass frame and clean

as per the instructions on page 6.

f) Refit the glass panel to the firebox, again tightening each bolt a

small amount at a time to prevent stressing the glass panel. Fully

tighten all the bolts to ensure good compression on the glass panel

seal.

g) Refit the brass trim, ashpan & fret to the firebox.

FOLLOWI G USE OF THE ALLE KEY, ALWAYS REMOVE IT FROM THE

FIRE A D REPLACE IT I TO ITS LOCATIO I THE CLIP AT THE BOTTOM

LEFT HA D SIDE OF THE FIREBOX.

REMOVAL / RE-FITTI G OF THE FUELBED

FITTI G THE FUELBED

Place the fuelbed centrally onto the fuelbed support. Ensure that the fuelbed is

located centrally into the firebox, and that the front outside face of the left and

right-hand fuelbed legs are touching the stainless steel fibre support trims.

See fig. 2 below

Fig. 2

NOTE : The position of the fuel-bed components are critical to the

performance of the product. Therefore please ensure that the fuel-bed

components are positioned as described in the following section prior to

requesting a service call due to soot build up, poor flame pattern etc.

Refit the glass frame as detailed in section on page 6, then light the appliance as

detailed on page 4.

To ensure that the release of fibres from these R.C.F (Refractory Ceramic

Fibre) articles is kept to a minimum, during installation and servicing we

recommend that you use a HEPA filtered vacuum to remove any dust

accumulated in and around the appliance before and after working on the

appliance. When replacing these articles we recommend that the replaced

items are not broken up, but are sealed within heavy duty polythene bags,

clearly labelled as “RCF waste”. RCF waste is classed as a “stable”, non

reactive hazardous waste and may be disposed of at a landfill licensed to

accept such waste Protective clothing is not required when handling these

articles, but we recommend you follow the normal hygiene rules of not

smoking, eating or drinking in the work area, and always wash your hands

before eating or drinking.

USER REPLACEABLE PARTS

The only user replaceable parts on this fire are the fuelbed / coal form, which may

be replaced as described in the above section. Replacement of any other parts

must be carried out by a competent person such as a CORGI registered gas

installer.

The part numbers of the user replaceable parts are as follows, these are available

from BF Europe Ltd. who may be contacted at the address shown on the below.

Fuelbed 70-47800

Due to our policy of continual improvement and development the exact

accuracy of descriptions and illustrations cannot be guaranteeD.

Part o. B-103840

Issue 3

BF Europe Ltd.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

www.bfm-europe.com

Telephone - General Enquiries : (01782) 339000

Telephone - Service : (0844) 7700169

Indice

Altri manuali Flavel Camino da interno

Flavel

Flavel Onyx MK2 FFHOW0RE2 Manuale utente

Flavel

Flavel Richmond Plus FOPC MN Series Istruzioni per il montaggio

Flavel

Flavel REGENT L.F.E. RC Istruzioni per il montaggio

Flavel

Flavel FKPC MN Series Istruzioni per il montaggio

Flavel

Flavel Windsor Istruzioni per il montaggio

Flavel

Flavel Calypso Istruzioni per il montaggio

Flavel

Flavel Emberglow Manuale utente

Flavel

Flavel Pure FPRG**RN2 Manuale utente

Flavel

Flavel Warwick FIRC14MN Manuale utente

Flavel

Flavel F33L**RU Series Manuale utente

Flavel

Flavel Linear HE Istruzioni per il montaggio

Flavel

Flavel FOPC MN Series Istruzioni per il montaggio

Flavel

Flavel Richmond Plus Manuale utente

Flavel

Flavel Renoir FRECR0MN Manuale utente

Flavel

Flavel Linear Pebble FRDPU0MN Manuale utente

Flavel

Flavel Curve FCRR Series Manuale utente

Flavel

Flavel Pure FPRG**RN2 Manuale utente

Flavel

Flavel ATLANTA FBFR**MN Manuale utente

Flavel

Flavel Caress Slimeline SC FNVC**SN Manuale utente

Flavel

Flavel Decadence HE Istruzioni per il montaggio

Flavel

Flavel Kamina Manuale utente

Flavel

Flavel Calibre FBFC**MN2 Istruzioni per il montaggio

Flavel

Flavel Windsor Istruzioni per il montaggio

Flavel

Flavel RENOIR RC Istruzioni per il montaggio

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo