Flex LINEAR LR20S-A Series Manuale utente

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

The LINEAR Series of commercial and industrial LED fixtures is designed to be used in utility strip applications using suspension or

surface mount installation. The LINEAR Series is designed for use in 120 –277V, 50/60Hz protected (max 20A) circuits.

Size line voltage Service wire as required per the National Electric Code (NEC).

GENERAL NOTES:

1. MAKE SURE ALL WIRE AND CONNECTORS ARE UL-LISTED. IF THE

ELECTRICAL SYSTEM CONTAINS NO GROUND WIRE, CONSULT

WITH A QUALIFIED ELECTRICIAN BEFORE PROCEEDING WITH THE

INSTALLATION.

2. SUSPENSION CABLE, CHAIN OR CEILING JUNCTION BOX PROVIDED

BY CONTRACTOR SHALL BE RATED TO SUPPORT WEIGHT OF

FIXTURE(S) –INCLUDING ALL ASSESSORIES AND OPTIONS.

AIRCRAFT SUSPENSION CABLE MAY BE ORDERED SEPARATELY

FROM FLEX LIGHTING SOLUTIONS OR OTHERWISE PROVIDED

BY CONTRACTOR.

ITEMS NOT INCLUDED:

(BUT REQUIRED FOR INSTALLATION):

PERSONAL PROTECTIVE EQUIPMENT



SCREWDRIVER



PLIERS



SUPPLY CONDUCTORS (BUILDING LINE POWER)



RECEPTACLE (IF APPLICABLE)

ITEMS INCLUDED:

LINEAR LED LIGHT FIXTURE (FXT, RTR OR RMW)

CORD AND PLUG (OPTIONAL; SOLD SEPARATELY)

MAY ALSO INCLUDE SOME OPTIONAL ACCESSORIES (IF

ORDERED)

REFER TO SPECIFICATION SHEET FOR ALL POSSIBLE OPTIONS.

These instructions apply to the following part numbers:

LR20S-Ax-xK-04-[xxx]-LV-FXT-[xxx]-10V

LR20S-Ax-xK-08-[xxx]-LV-FXT-[xxx]-10V

LR20S-Ax-xK-12-[xxx]-LV-FXT-[xxx]-10V

LR20S-Ax-xK-04-[xxx]-LV-RTR-[xxx]-10V

LR20S-Ax-xK-08-[xxx]-LV-RTR-[xxx]-10V

LR20S-Ax-xK-12-[xxx]-LV-RTR-[xxx]-10V

LR20S-Ax-xK-04-[xxx]-LV-RMW-[xxx]-10V

LR20S-Ax-xK-08-[xxx]-LV-RMW-[xxx]-10V

LR20S-Ax-xK-12-[xxx]-LV-RMW-[xxx]-10V

4' LINEAR STANDALONE FIXTURE

ISOMETRIC VIEW

4' LINEAR RETROFIT KIT

ISOMETRIC VIEW

4' LINEAR RETRO

MULTI WIDTH KIT

(BACKBOX NOT INCLUDED)

ISOMETRIC VIEW

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

WARNING:

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DEATH, SERIOUS INJURY OR SIGNIFICANT PROPERTY DAMAGE.

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH APPLICABLE BUILDING AND ELECTRICAL CODES, BY A QUALIFIED PERSON WHO IS FAMILIAR WITH THE CONSTRUCTION

AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE

PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS



FULLY INSPECT LENS AND HOUSING OF THE FIXTURE PRIOR TO INSTALLATION. IF

DAMAGED, NOTIFY FACTORY.



TO AVOID ELECTRIC SHOCK: DISCONNECT ELECTRICAL POWER (LINE POWER)

BEFORE AND DURING INSTALLATION AND MAINTENANCE.



VERIFY SUPPLY VOLTAGE IS SAME AS RATED FIXTURE VOLTAGE. THE ELECTRICAL

RATINGS OF THE FIXTURE ARE CLEARLY INDICATED ON THE PRODUCT LABEL.



SUITABLE FOR DRY AND DAMP LOCATIONS ONLY.



BE CAUTIOUS OF ANY SHARP EDGES. WEAR PROPER SAFETY GEAR (SUCH AS

GLOVES AND SAFETY GLASSES) WHILE HANDLING.

CAUTION - RISK OF PERSONAL INJURY

ACCOUNT FOR SMALL PARTS AND DESTROY PACKING MATERIAL, AS THESE MAY BE

HAZARDOUS TO CHILDREN

CAUTION - RISK OF FIRE



MINIMUM 90º C SUPPLY CONDUCTORS.



NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.

WARNING -



RISK OF FIRE OR ELECTRIC SHOCK—LUMINAIRE WIRING AND ELECTRICAL PARTS MAY

BE DAMAGED WHEN DRILLING FOR INSTALLATION OF RETROFIT ASSEMBLY

HARDWARE. CHECK FOR ENCLOSED WIRING AND COMPONENTS.

AVERTISSEMENT - RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE. CÂBLAGE DU

LUMINAIRE ET PIÈCES ÉLECTRIQUES PEUVENT ÊTRE ENDOMMAGÉS LORS DU FORAGE

POUR L'INSTALLATION DU KIT DE CONVERSION À DEL. VÉRIFIER LE CÂBLAGE ET LES

COMPOSANTS CLOS

CAUTION - RISK OF ELECTRIC SHOCK



SUITABLE FOR DAMP LOCATIONS

CONVIENT AUX EMPLACEMENTS HUMIDES



SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45 °C

PEUT ÊTRE UTILISÉ À UNE TEMPÉRATURE AMBIANTE N’EXCÉDANT PAS

45°C



LR20S-Ax-xK-08 -

SUITABLE FOR OPERATION IN AMBIENT NOT

EXCEEDING 40 °C

PEUT ÊTRE UTILISÉ À UNE TEMPÉRATURE AMBIANTE N’EXCÉDANT PAS

40°C



USE INDOORS ONLY.



TURN POWER OFF BEFORE SERVICING -- SEE INSTRUCTIONS.



PROPERLY GROUND FIXTURE.

WARNING -



ENSURE NO BARE WIRES ARE EXPOSED OUTSIDE

THE ELECTRICALCONNECTIONS.



TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT

EXPOSE WIRING TO EDGES OR OTHER SHARP OBJECTS.



ONLY THOSE OPEN HOLES INDICATED IN THE

PHOTOGRAPHS ANDOR DRAWINGS MAY BE MADE OR

ALTERED AS A RESULT OF KIT INSTALLATION. DO NOT

LEAVE ANY OTHER OPEN HOLES IN AN ENCLOSURE OF

WIRING OR ELECTRICAL COMPONENTS.

SEULS LES OUVERTURES INDIQUÉES DANS LES PHOTOS

ET/OU LES DESSINS PEUVENT ÊTRE FAITS OU MODIFIÉS À

LA SUITE DE L'INSTALLATION DU NÉCESSAIRE. IL EST

INTERDIT DE LAISSER D'AUTRES OUVERTURES DANS UN

BOÎTIER DE CÂBLAGE OU DE COMPOSANTS ÉLECTRIQUES.

THESE INSTRUCTIONS DO NOT ATTEMPT TO COVER ALL INSTALLATION AND MAINTENANCE SITUATIONS. FOR MORE INFORMATION OR QUESTIONS REGARDING THE INSTALLATION

OR USE OF THE ESSENTIALS FIXTURE, CALL 913-851-3000 OR EMAIL AT

[email protected].

MAINTENANCE

LINEAR FIXTURES SHOULD BE DRY DUSTED PERIODICALLY. THE FROSTED LENS CAN BE CLEANED WITH DAMP OR DRY CLOTH. NO SPECIAL CLEANER REQUIRED.

TROUBLESHOOTING

TURN ELECTRICITY OFF AT THE MAIN CIRCUIT BREAKER, PANELBOARD, FUSE BOX OR DISCONNECT. DO NOT ATTEMPT TO TROUBLESHOOT WITH THE POWER ON.

ISSUE 1 - LIGHT DOES NOT COME ON

1. VERIFY THAT POWER IS BEING DELIVERED TO THE FIXTURE. CHECK ALL UPSTREAM CIRCUIT BREAKERS, FUSES AND DISCONNECT TO ENSURE THEY ARE ON AND IN PROPER WORKING

ORDER.

2. CONFIRM ALL ELECTRICAL CONNECTIONS ARE COMPLETE AND CONTINUOUS.

3. IF THE ISSUE REMAINS UNRESOLVED, CONTACT FLEX LIGHTING SOLUTIONS.

ISSUE 2 - ONE OR MORE LEDS ARE OUT WHILE OTHERS REMAIN ON

1. DETERMINE IF REPLACEMENT IS DESIRED. AFTER ONE OR MORE LEDS FAILS, THE FIXTURE MAY CONTINUE TO OPERATE NORMALLY, ALTHOUGH WITH A REDUCED LUMEN OUTPUT.

2. IF REPLACEMENT FIXTURE IS DESIRED, CONTACT FLEX LIGHTING SOLUTIONS.

WARRANTY SUPPORT

PHONE: +1 913-851-3000

EMAIL:

[email protected]

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

GENERAL INSTRUCTIONS:

PREPARING TO INSTALL

1. CONSULT A LOCAL LICENSED ELECTRICIAN OR ELECTRICAL CONTRACTOR PRIOR TO INSTALLATION.

2. REVIEW WARNINGS FOUND IN THIS DOCUMENT PRIOR TO STARTING WORK.

3. INSPECT PACKAGE(S) FOR SIGNS OF DAMAGE. NOTIFY CARRIER IMMEDIATELY IF FIXTURE PACKAGING IS DAMAGED.

4. UNPACK THE FIXTURES FROM PACKAGING. RECYCLE AND PROPERLY DISPOSE OF PACKAGING.

5. INSPECT FIXTURES. IF THERE IS ANY FIXTURE DAMAGE OBSERVED, TAKE PHOTOGRAPHS AND IMMEDIATELY CONTACT LIGHTING.TECH@FLEX.COM.

6. TURN OFF ELECTRICITY AT THE MAIN CIRCUIT BREAKER, PANELBOARD, FUSE BOX OR DISCONNECT.

DO NOT ATTEMPT TO INSTALL FIXTURE WITH THE POWER ON.

ENSURE FIXTURE IS PROPERLY RATED FOR RESPECTIVE LOCATION.

MAKE SURE THE MOUNTING SURFACE IS CAPABLE OF SUPPORTING WEIGHT OF FIXTURE.

MAX AMBIENT REDUCED 5°C WHEN MOUNTED NEAR CEILING.

10.

ENSURE PROPER AIRFLOW AROUND FIXTURE.

REMOVING LED LIGHT COVER (FXT ONLY):

1. GENTLY SQUEEZE THE LINEAR HOUSING BELOW THE SIDE TABS AND REMOVE THE LED LIGHT COVER TO ACCESS FIXTURE WIRING.

2. IF APPLICABLE, REMOVE DRIVER GREEN/YELLOW STRIPE GROUND WIRE FROM GROUNDING WAGO CONNECTOR.

3. SET LED LIGHT COVER ASIDE UNTIL READY TO MAKE ELECTRICAL CONNECTIONS. REFER TO “MAKING ELECTRICAL CONNECTIONS” FOR WIRING INFORMATION.

4. DETERMINE HOW FIXTURE WILL BE MOUNTED, AND GO TO APPROPRIATE INSTRUCTION.

JOINING FIXTURE SECTIONS (FXT ONLY):

1. IDENTIFY SECTIONS –

8’ SECTIONS ARE MARKED “8A” AND “8B”

12’ SECTION ARE SECTIONS MARKED “12A”, “12B” AND “12C”.

SECTION “8A (12A)” HAS THE DRIVER.

8 FT SECTION COMES WITH 3 END CAPS: (1 EA) INSTALLED ON “8A”SECTION, (1 EA) INSTALLED ON “8B”SECTION, (1 EA) ENDCAP WRAPPED UP AND

TUCKED INSIDE HOUSING OF SECTION “8B”AND (1 EA) JOINER PLATE.

12 FT SECTION COMES WITH 4 END CAPS: (1 EA) INSTALLED ON “12A”SECTION, (1 EA) INSTALLED ON “12C” SECTION, (2 EA) ENDCAPS WRAPPED

UP AND TUCKED INSIDE HOUSING OF SECTION “12B”AND (2 EA) JOINER PLATES.

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

JOINING FIXTURE SECTIONS –cont. (FXT ONLY):

2. ORIENT EACH FIXTURE SECTION IN THE SAME DIRECTION. PLACE FIXTURES END TO END AS THEY WOULD BE INSTALLED.

8FT LINEAR –“8A” ALIGNS WITH “8B”;

12FT LINEAR –“12A” ALIGNS WITH “12B,” WHICH ALIGNS WITH “12C”.

3. REMOVE LIGHT COVER FROM EACH SECTION. (SEE “REMOVING LIGHT COVER INSTRUCTION”)

4. 8FT FIXTURE:

LOCATE LOOSE ENDCAP IN SECTION “8B”. REMOVE FROM PACKAGING.DISPOSE OF PACKAGING PROPERLY.

LOCATE SLOTS AT END OF HOUSING IN SECTION “8A”. ALIGN ENDCAP WITH SLOTS AND SLIDE ENDCAP INTO PLACE. ENDCAP SHOULD SLIDE ALL THE

WAY TO END OF SLOTS.

ALIGN ENDCAP ON SECTION “8A” WITH SLOTS ON SECTION “8B” AND SLIDE ENDCAP INTO SLOTS. ENDCAP SHOULD SLIDE ALL THE WAY TO END OF

SLOTS IN SECTION B. AFTER JOINING, FIXTURES HOUSINGS FROM BOTH SECTIONS SHOULD BE FLUSH TOGETHER.

LOCATE JOINER PIECE. INSERT SLOTS THROUGH NOTCHES LOCATED IN THE SIDE OF THE FIXTURE HOUSING. ONE HALF OF JOINER WILL BE IN

SECTION “8A” AND ONE HALF OF THE JOINER WILL BE IN SECTION “8B.” CLOSE JOINER PIECE OVER TOP OF ENDCAP.

PRESS CENTER BETWEEN SLOTS OF JOINER PIECE SO THAT SLOTS WILL INSERT THROUGH NOTCHES IN SIDE OF FIXTURE HOUSING.

FIXTURE IS NOW READY TO MOUNT. PROCEED TO THE APPROPRIATE APPLICABLE MOUNTING INSTRUCTIONS.

SECTION “8A”

SECTION “8B”

PROPERLY JOINED

SECTION “8A”

ENDCAP

SECTION “8A”

SECTION “8B”

ENDCAP

JOINER

PIECE

SECTION “8A”

SECTION “8B”

SECTION “8A”

SECTION “8B”

SECTION “8A”

JOINER

PIECE

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

JOINING FIXTURE SECTIONS –cont. (FXT ONLY):

5. 12FT FIXTURE:

FOLLOW “8FT FIXTURE” INSTRUCTIONS NUMBER 4 ABOVE TO JOIN SECTIONS “12A” AND “12B.”

JOINING SECTION “12C”: LOCATE SECOND LOOSE ENDCAP IN SECTION “12B”. REMOVE FROM PACKAGING. DISPOSE OF PACKAGING PROPERLY.

LOCATE SLOTS AT END OF HOUSING IN SECTION “12B”. ALIGN ENDCAP WITH SLOTS AND SLIDE ENDCAP INTO PLACE. ENDCAP SHOULD SLIDE ALL

THE WAY TO END OF SLOTS.

ALIGN ENDCAP ON SECTION “12B” WITH SLOTS ON SECTION “12C” AND SLIDE ENDCAP INTO SLOTS. ENDCAP SHOULD SLIDE ALL THE WAY TO END OF

SLOTS IN SECTION C. AFTER JOINING, FIXTURE HOUSINGS FROM BOTH SECTIONS SHOULD BE FLUSH TOGETHER.

PRESS CENTER BETWEEN SLOTS OF JOINER PIECE SO THAT SLOTS WILL INSERT THROUGH NOTCHES IN SIDE OF FIXTURE HOUSING.

FIXTURE IS NOW READY TO MOUNT. PROCEED TO THE APPROPRIATE APPLICABLE MOUNTING INSTRUCTIONS.

STAND ALONE FIXTURE (FXT) –SUSPENSION MOUNT

1. INSTRUCTION TO FOLLOW USES FLS HANGERKIT (SOLD SEPARATELY).

HANGERKIT –ITEMS INCLUDED:

“Y” TOGGLE AND GRIPPER

LOOP CABLE.

LOOP CABLE

“Y” TOGGLE AND GRIPPER”

TOGGLE

GRIPPER

SECTION “12B”

SECTION “12C”

PROPERLY JOINED

SECTION “12B”

ENDCAP

SECTION “12B”

SECTION “12C”

ENDCAP

JOINER

PIECE

SECTION “8A”

SECTION “8B”

SECTION “12B”

SECTION “12C”

SECTION “8B”

SECTION “12B”

JOINER

PIECE

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

INSTALLING SUSPENSION MOUNT (FXT):

1. SEE GENERAL INSTRUCTIONS AT THE FRONT OF THIS INSTRUCTION.

2. 4’ SECTION: PRESS GRIPPER AGAINST CABLE SO GRIPPER AND CABLE ARE PARALLEL.

3. INSERT GRIPPER/CABLE INTO FIXTURE THROUGH OBLONG HOLES AT END OF FIXTURE.

4. PUSH GRIPPER/CABLE THROUGH HOLE UNTIL GRIPPER CANNOT BE HANDLED (IS NOT SEEN).

5. PULL CABLE TIGHT. GRIPPER LAYS INSIDE FIXTURE HOUSING AND WILL NOT PULL OUT.

6. SECURE HANGER CABLE TO STRUCTURE.

a. 4FT SECTION: MINIMUM 2 HANGER POINTS

b. 8FT SECTION: MINIMUM 3 HANGER POINTS OR 4 HANGER POINTS.

c. 12FT SECTION: MINIMUM 4 HANGER POINTS OR 6 HANGER POINTS.

7. PASS LOOP SIDE OF CABLE OVER, AROUND AND UNDER STRUCTURE.

8. PASS STRAIGHT END OF CABLE THROUGH LOOP AND PULL TIGHT.

9. RAISE FIXTURE WITH “Y” TOGGLE AND GRIPPER TO LOOP CABLE SECURED TO STRUCTURE.

10. PASS STRAIGHT END OF LOOP CABLE THROUGH TOGGLE. PLUNGER ON TOP OF TOGGLE CATCHES AND HOLDS CABLE SECURELY.

11. LEVEL FIXTURE PLUMB WITH BUILDLING LINES. (TO LET OUT CABLE, PUSH PLUNGER DOWN).

12. MAKE FINAL WIRING CONNECTIONS. REFER TO “MAKING ELECTRICAL CONNECTIONS”.

13. 8’ SECTION: FOLLOW INSTRUCTIONS FOR “4FT SECTION”, NUMBERS 2 THROUGH 5 TO INSTALLED TOGGLE AND GRIPPER.

14. INSTALLING MIDDLE TOGGLE/GRIPPER FOR 3 HANGER POINTS: PRESS GRIPPER AGAINST CABLE SO GRIPPER AND CABLE ARE PARALLEL.

SECTION THROUGH FIXTURE

FIXTURE

STRUCTURE

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

15. INSERT GRIPPER/CABLE INTO FIXTURE THROUGH OBLONG HOLES AT END OF FIXTURE.

16. SECURE HANGER CABLE (SOLD SEPARATELY) TO STRUCTURE (3 OR 4 HANGER POINTS AS APPLICABLE). ATTACH HANGER CABLE TO MOUNTING HOLES IN BACK

OF FIXTURE. MINIMUM 3 HANGER POINTS REQURIED.

17. RAISE FIXTURE WITH “Y” TOGGLE AND GRIPPER TO LOOP CABLE SECURED TO STRUCTURE.

18. PASS LOOP CABLE THROUGH TOGGLE. PLUNGER ON TOP OF TOGGLE CATCHES AND HOLDS CABLE SECURELY.

19. LEVEL FIXTURE PLUMB WITH BUILDLING LINES. (TO LET OUT CABLE, PUSH PLUNGER DOWN)

20. MAKE FINAL WIRING CONNECTIONS. REFER TO “MAKING ELECTRICAL CONNECTIONS”.

21. 12’ SECTION: FOLLOW INSTRUCTIONS FOR “4FT SECTION”, NUMBERS 2 THROUGH 5 TO INSTALLED TOGGLE AND GRIPPER.

22. INSTALLING MIDDLE TOGGLE/GRIPPERS FOR 4 HANGER POINTS: PRESS GRIPPER AGAINST CABLE SO GRIPPER AND CABLE ARE PARALLEL.

23. INSERT GRIPPER/CABLE INTO FIXTURE THROUGH OBLONG HOLES AT END OF FIXTURE.

24. SECURE HANGER CABLE (SOLD SEPARATELY) TO STRUCTURE (4 OR 6 HANGER POINTS AS APPLICABLE). ATTACH HANGER CABLE TO MOUNTING HOLES IN BACK

OF FIXTURE. MINIMUM 4 HANGER POINTS REQURIED.

25. RAISE FIXTURE WITH “Y” TOGGLE AND GRIPPER TO LOOP CABLE SECURED TO STRUCTURE.

26. PASS LOOP CABLE THROUGH TOGGLE. PLUNGER ON TOP OF TOGGLE CATCHES AND HOLDS CABLE SECURELY.

27. LEVEL FIXTURE PLUMB WITH BUILDLING LINES. (TO LET OUT CABLE, PUSH PLUNGER DOWN)

28. MAKE FINAL WIRING CONNECTIONS. REFER TO “MAKING ELECTRICAL CONNECTIONS”.

MIDDLE TOGGLE/GRIPPER FOR 3

HANGER POINTS

3 POINT MOUNT

4 POINT MOUNT

MIDDLE TOGGLE/GRIPPER FOR 4

HANGER POINTS

4 POINT MOUNT

6 POINT MOUNT

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

STAND ALONE FIXTURE (FXT) –SURFACE MOUNT

INSTALLING SURFACE MOUNT (FXT):

1. SEE GENERAL INSTRUCTIONS AT THE FRONT OF THIS SECTION.

2. 8FT AND 12FT SECTIONS: FOLLOW “JOINING FIXTURE SECTIONS” INSTRUCTIONS.

3. DRIVER IS LOCATED IN SECTION “A.”

4. AC POWER MAY BE FOUND INSTALLED INTO THE BACK, MIDDLE OR SIDE OF THE FIXTURE. ADJUST AC POWER LOCATION, IF APPLICABLE.

5. CHOOSE A SUITABLE KNOCKOUT LOCATION FROM THOSE PROVIDED. REMOVE THE KNOCKOUT WITH A SCREWDRIVER.

6. REMOVE LED COVER. (REFER TO SECTION “REMOVING LED COVER – (FXT ONLY)” OF THIS INSTRUCTION.)

7. LIFT FIXTURE HOUSING TO CEILING AND MARK THE MOUNTING HOLES WITH A PENCIL.

8. PULL EXISTING AC POWER FROM BUILDING THROUGH KNOCKOUT LOCATION INTO FIXTURE HOUSING. PROVIDE UL APPROVED STRAIN RELIEF (NOT PROVIDED)

AS REQUIRED.

9. RAISE FIXTURE HOUSING TO SURFACE AND SECURE WITH APPROPRIATE CONNECTOR(S).

10. MAKE FINAL WIRING CONNECTIONS. REFER TO “MAKING ELECTRICAL CONNECTIONS”.

PREPARING EXISTING FIXTURE FOR RETROFIT KIT (RTR) OR RETRO MULTI WIDTH KIT (RMW)

PREPARING EXISTING FIXTURE:

1. SEE GENERAL INSTRUCTIONS AT THE FRONT OF THIS SECTION.

2. RETROFIT LUMINAIRE CONVERSION KIT IS SUITABLE FOR USE IN A FULLY ENCLOSED LUMINAIRE.

3. RETROFIT LUMINAIRE CONVERSION KIT IS NOT INTENDED FOR DIRECT CONTACT WITH WATER.

4. IDENTITY FLUORESCENT FIXTURE BEING UPGRADED WITH LED RETROFIT KIT.

5. TURN FLUORESCENT FIXTURE OFF AND ALLOW LAMPS TO COOL PRIOR TO STARTING WORK.

6. IF FLUORESCENT FIXTURE HAS LENS OR DIFFUSER, REMOVE TO GAIN ACCESS TO LAMPS.

SECTION “A”

TRADITIONAL

FLUORESCENT

FIXTURE

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

7. ONCE FLUORESCENT TUBE LAMPS HAVE COOLED AND CAN BE HANDLED WITHOUT RISK OF BURN, CAREFULLY REMOVE FROM EXISTING FIXTURE. AVOID

BREAKING LAMPS.

8. REMOVE EXISTING FASTENERS AND COVER FROM EXISTING FIXTURE. INVENTORY FASTENERS THAT WERE REMOVED (SCREWS, QUARTER TURN FASTENERS,

ETC.) AND RETAIN FOR LED RETROFIT KIT INSTALLATION.

9. THE BI-PIN FLUORESCENT SOCKETS WILL NOT BE USED WITH THE NEW LED RETROFIT KIT, REMOVE BY CUTTING WIRES FROM SOCKETS TO INCOMING POWER

FEED AND BALLAST AND REMOVE SOCKETS. CAP WIRES LEFT IN CHANNEL WITH WIRE NUTS OR UL APPROVED ELECTRICAL TAPE (NOT PROVIDED). TO

ABANDON SOCKETS IN PLACE (IF ALLOWED BY LOCAL CODES AND AUTHORITY HAVING JURISDICTION), TURN SOCKETS DOWN INTO METAL CHANNEL AND

NEATLY ARRANGE IN METAL CHANNEL TO AVOID INTERFERENCE WITH NEW LED RETROFIT KIT. USE UL APPROVED ELECTRICAL TAPE TO MOVE ABANDONED

SOCKETS AND WIRE OUT OF THE WAY IF NECESSARY.

10. DISCONNECT EXISTING FLUORESCENT BALLAST FROM INCOMING POWER FEED BY CUTTING BLACK AND WHITE WIRES. BALLAST CONNECTORS CAN BE

RETAINED IF WIRES ARE CUT ON THE LOAD SIDE OF THE BALLAST CONNECTORS (CLOSEST TO THE BALLAST). ABANDON BALLAST IN PLACE (IF ALLOWED BY

LOCAL CODES AND AUTHORITY HAVING JURISDICTION (AHJ)) OR REMOVE. IF BALLAST IS ABANDONED, CAP OF CUT WIRES WITH WIRE NUTS OR UL APPROVED

ELECTRICAL TAPE (NOT INCLUDED). DISPOSE OF UNUSED BALLAST PER LOCAL CODES, IF APPLICABLE.

11. DISCONNECT GROUND FROM FLUORESCENT BALLAST. REMOVE WIRE NUT (IF APPLICABLE) OR CUT GREEN WIRES.

PREPARE EXISTING WIRING (IF APPLICABLE):

1. USING WIRE CUTTERS, REMOVE INSULATION ON WIRES APPROXIMATELY 3/8" FROM WIRE END. TAKE CARE NOT TO DAMAGE THE COPPER CONDUCTORS.

RETROFIT KIT (RTR)

INSTALLING KIT:

1. REFER TO “PREPARING EXISTING FIXTURE FOR RETROFIT KIT (RTR) OR RETRO MULTI WIDTH KIT (RMW)”.

2. REFER TO “MAKING ELECTRICAL CONNECTIONS”.

INSTALLATIONINSTRUCTIONS

LINEAR SERIES

IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR

SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.

FLEXLIGHTINGSOLUTIONS.COM LIGHTING.TECH@FLEX.COM 913-851-3000 11-13-17

RETRO MULTI WIDTH KIT (RMW)

PREPARING BRACKETS:

1. REFER TO “PREPARING EXISTING FIXTURE FOR RETROFIT KIT (RTR) OR RETRO MULTI WIDTH KIT (RMW)”.

2. BREAK APART BRACKETS.

3. MEASURE WIDTH OF EXISTING HOUSING.

4. SELECT THE APPROPRIATE WIDTH OF TABS ON THE MULTI WIDTH BRACKET.

5. EACH BRACKET IS SET UP IN 1/2” INCREMENTS (EACH SIDE).

6. USING PLIERS, BEND APPROPRIATE TABS AT 90° SO IT CAN BE ATTACHED TO HOUSING WITH SELF TAPPING SHEET METAL SCREWS.

7. BEND HINGE POINT AT 90° DOWN TOWARDS HOUSING (AS SHOWN).

3.25”

”

4.25”

5.25”

6.25”

Indice

Altri manuali Flex Apparecchio di illuminazione

Flex

Flex LS10S-A1-03K-04-35-80-FR-FXT Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente