FlexDSL MiniFlex SHDSL Manuale utente

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 1/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

Ddd

The FlexDSL Orion3 and MiniFlex SHDSL.bis product family offers a broad range of products, which are based on the latest

SHDSL.bis standards (ITU-T G.991.2 & ETS TS 101524), while also being fully interoperable with all our existing SHDSL

equipment (Orion1, Orion2). The FlexDSL MiniFlex supports beside of the standardized TC-PAM16/32 also the new extended

TC-PAM4/8/64/128 line coding. The support of these extended line codes ensures compatibility with existing SHDSL

equipment, that is already installed, in order to protect customer investments, while at the same time providing an upgrade

path to the newest DSL technologies.

The MiniFlex product family supports beside of SHDSL.bis copper transmisson a dinrail Fiber Converter unit. It has equal

dimensions and supports datarates up to 100Mbps over fiber.

SHDSL.bis allows symmetrical data and voice transmission at speeds up to 15Mbps over a single pair of copper. In addition,

the FlexDSL MiniFlex SHDSL.bis modem range also supports DSL channel bonding for up to 2 copper pairs in order to

achieve speeds to 30.4Mbps!!. An integrated 2 port Ethernet layer 2 managed switch with VLAN, QoS and RSTP support

(10/100BaseT) ensures connectivity to IP services. The FlexDSL MiniFlex SHDSL.bis modems is a perfect solution for a wide

range of applications in which IP services need to be transmitted over copper wires. The MiniFlex product is a small-sized

Orion3 unit with all the functionality included.

Like all FlexDSL Orion products the FlexDSL MiniFlex SHDSL.bis modems are based on industrial components and

manufactured according to highest quality standards providing additional value due to the extended temperature ranges and

higher reliability. The combination of comprehensive functions providing maximum flexibility together with the higher quality of

the FlexDSL MiniFlex SHDSL.bis product family make it the perfect choice for all your DSL needs.

Possible Applications

a) Ethernet Transmission Point-to-Point

b) Ethernet Transmission Point-to-Multipoint

c) Ethernet Add/Drop over a Long Copper Line

b) c)

SHDSL.bis

Up to 3

0Mbps

Ethe

rnet

FlexDSL

MiniFlex

Features

•Up to 15Mbps Data Transmission per Copper Pair

•SHDSL and SHDSL.bis, TC-PAM16/32

•Additional TC-PAM4/8/64/128 Available

•Up to 100Mbps Data Transmission per Fiber Line (SFP)

•1 or 2 Copper Pairs Support

•1 or 2 Fiber Line Support (SFP)

•2 Port Ethernet Switch (10/100BaseT)

•QoS, VLAN and RSTP Support

•Point-to-Point and Point-to-Multipoint Operation

•Ring Applications

•Console Port, Telnet, Web, SNMP Management

•24/48VDC or 110/230VAC Powered, Low Power Consumption

•Included Primary Protection

•Robust DIN-Rail Metal Enclosure

•Smallest Size

•Industrial Temperature Range Available

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 2/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

Quick Installation Guide

Enter a MiniFlex Device

You can use the Monitor (Local Craft Terminal, USB) interface with Hyper Terminal (or any equal program) or you can

address the device with Telnet through the Ethernet interface.

Monitor (LCT, USB) Interface:

•Configure the COM port: Bits per second:9600, Data bits: 8, Parity: None, Stop bits: 1, Flow control: None

•Press <ENTER>.

Telnet through Ethernet Interface:

•Type in command line <Telnet 192.168.0.235> and press <ENTER>. This is the default Ethernet Address for MiniFlex

devices.

After a successful entering the main menu of the device will be displayed.

Configure a MiniFlex Device

A first installation example with the most important commands and points to care about is shown below. We just like to have

an Ethernet transmission between the two devices over 2 SHDSL copper pairs with a speed of 11.4Mbit/s. The pairs should

aggregate (bundle) the data traffic and in case of any SHDSL pair failure, the remaining pairs should continue to work.

Enter in device 1 with the Monitor (LCT, USB) or Telnet interface.

Type following commands Description

3 <↵> Go to Configuration Management (CM)

<DEFAULT EVERYTHING> <↵> Set everything to default configuration

<MASTER ON 1> <↵> Configure SHDSL 1 as MASTER

<MASTER ON 2> <↵> Configure SHDSL 2 as MASTER

<PAYLOAD WAN 1> <↵> Configure Ethernet over SHDSL 1

<PAYLOAD WAN 2> <↵> Configure Ethernet over SHDSL 2

<NET> <↵> Go to NET menu

<SETIP 10.0.2.200> <↵> Set the IP-address of the device

<NETMASK 255.0.0.0> <↵> Set the subnet mask

<GATEWAY 10.0.0.101> <↵> Set the default gateway

<M> <↵> Go to Configuration Management (CM)

<M> <↵> Go to Main Menu

2 <↵> Go to Fault and maintenance management (FMM)

<APPLY ALL> <↵> Apply all configurations (written in the running config.)

<CONFIRM> <↵> Confirm all configurations (written in the startup config.)

Device 1

Device 2

Computer

100Mbps Fiber Ring

15Mbps Copper Ring

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 3/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

In Menu Configuration Management (CM) you can type <CONFIG> to see the following picture:

CO_CM>CONFIG

--------------------------------------------------------------------------------

Running Line Configuration

--------------------------------------------------------------------------------

xDSL DSL1 DSL2

Mode : Master(HTU-C) Master(HTU-C)

Extended rates: OFF OFF

Line coding : PAM32 PAM32

Baserate : 89 89

Annex : B B

Payload : WAN WAN

Clock source : Int Int

GS compatible : OFF

NM threshold : OFF

LA threshold : OFF

--------------------------------------------------------------------------------

CO_CM>

Enter in device 2 with the Monitor (LCT, USB) or Telnet interface.

Type following commands Description

3 <↵> Go to Configuration Management (CM)

<DEFAULT EVERYTHING> <↵> Set everything to default configuration

<MASTER OFF 1> <↵> Configure SHDSL 1 as SLAVE

<MASTER OFF 2> <↵> Configure SHDSL 2 as SLAVE

<PAYLOAD WAN 1> <↵> Configure Ethernet over SHDSL 1

<PAYLOAD WAN 2> <↵> Configure Ethernet over SHDSL 2

<NET> <↵> Go to NET menu

<SETIP 10.0.2.201> <↵> Set the IP-address of the device

<NETMASK 255.0.0.0> <↵> Set the subnet mask

<GATEWAY 10.0.0.101> <↵> Set the default gateway

<M> <↵> Go to Configuration Management (CM)

<M> <↵> Go to Main Menu

2 <↵> Go to Fault and maintenance management (FMM)

<APPLY ALL> <↵> Apply all configurations (written in the running config.)

<CONFIRM> <↵> Confirm all configurations (written in the startup config.)

In Menu Configuration Management (CM) you can type <CONFIG> to see the following picture:

CP_CM>CONFIG

--------------------------------------------------------------------------------

Running Line Configuration

--------------------------------------------------------------------------------

xDSL DSL1 DSL2

Mode : Slave(HTU-R) Slave(HTU-R)

Extended rates: OFF OFF

Line coding : PAM32 PAM32

Baserate : 89 89

Annex : B B

Payload : WAN WAN

Clock source : Int Int

GS compatible : OFF

NM threshold : OFF

LA threshold : OFF

--------------------------------------------------------------------------------

CP_CM>

The idea is the following: the default settings help any device to be in an initial state, then the MASTER/SLAVE mode is

enabled on the modem, then the transmit data is configured, then the network settings are configured (IP address, default

subnet mask and default gateway) and finally, these settings are applied and then are written in the EEPROM.

ATTENTION

DON’T FORGET TO WRITE THE CONFIGURATION IN THE STARTUP CONFIGURATION WITH

THE FOLLOWING COMMANDS:

2 <↵> Go to Fault and maintenance management (FMM)

<APPLY ALL> <↵> Apply all configurations (written in the running config.)

<CONFIRM> <↵> Confirm all configurations (written in the startup config.)

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 4/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

Connector Description

SHDSL Technical Specification

SHDSL Connector Specification

Specification ITU-T G.991.2 G.shdsl and G.shdsl.bis Pin No Description

Line Code TC-PAM16/32, Extended: TC-PAM4/8/64/128 1 SHDSL interface A

Impedance 135Ω2 SHDSL interface A

Transmit Power 13.5 (Annex A) or 14.5 (Annex B) dBm @ 135Ω3 SHDSL interface B

Number of Pairs 2

4 SHDSL interface B

Bit Rate 192 to 5704kbit/s, Extended: 128 to 15232kbit/s

Overvoltage Protection ITU-T Rec. K.20/K.21

Connector Type Phoenix Mini Combicom

MC 1,5/4-GF-3,5 (female), 4 pins.

Matching Type for the cable FK-MCP 1,5/ 4-STF-3,5

For AWG 16-26, Area 0.14–1.5 mm2or Diameter

0.4-1.4 mm

Fiber Optic Technical Specification (100Base-FX)

SFP Connector

Standard IEEE-802.3, VLAN/QoS IEEE-802.1q/p

Number of Interfaces 1

Data Rate 100BaseT, Full/Half Duplex, Ethernet

Connector Type Type –SFP Tyco 1658391-1

Recommended 155Mbps SFP Transceiver (Fast Ethernet, OC-3, STM-1):

LS38-A3S-TC-N

XGSF-03-1503-80

Ethernet Technical Specification

Ethernet Connector Specification

Standard IEEE-802.3, VLAN/QoS IEEE-802.1q/p Pin No Description

Number of Interfaces 2 or 1 1 Tx+ (transmit data)

Data Rate 10/100BaseT, Full/Half Duplex 2 Tx- (transmit data)

Protocols Data, Telnet, SNMP, WEB 3 Rx+ (receive data)

Signal Level Ethernet 4 NC (not used)

MDI/MDI-X auto crossover Supported 5 NC (not used)

Auto Negotiation Supported 6 Rx- (receive data)

Connector Type RJ45 Female, 8 pin 7 NC (not used)

8 NC (not used)

Monitor/Local Craft Terminal Technical Specification

Monitor/LCT Connector Specification

Specification USB V2.0 full and low speed Pin No Description

Data Rate 12Mbit/s 1 +5V

Protocol Master/Slave, Uses the USB communication 2 Data -

device class (CDC) drivers to take advantage of 3 Data +

the installed PC RS-232 software to talk over the

4 NC (not used)

USB

5 SGND

Connector Type USB Type Mini-B female connector

Power Supply Technical Specification

Power Supply Connector Specification

Specification ETSI ETS 300 132-2 Pin No Description

Voltage (-24V models) 18-72VDC local power 1 Negative power terminal or

N (Neutral power terminal)

Voltage (-230V models) 85-264VAC, 120-370VDC local power 2 Protection ground

Connector Type Phoenix Combicom

MSTB 2,5/ 3-GF-5,08(male), 3 pins.

3 Positive power terminal or

L (Life power terminal)

Matching Type for the cable FKCT 2,5/ 3-STF-5.08

For AWG 12-24, Area 0.2–2.5 mm2or Diameter

0.5-1.75 mm

Power Consumption Typically 4 Watts

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 5/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

Panel Description MiniFlex SHDSL

Connector LED RED GREEN AMBER OFF

xDSL 1 (DSL No 1) 1 DSL not working DSL normal operation

xDSL 2 (DSL No 2) 2 DSL not working DSL normal operation

Ethernet 1 and 2 Left Blinking = Data Connection not active

Ethernet 1 and 2 Right 100 Mbit/s data rate 10 Mbit/s data rate

Panel Description MiniFlex Single FOM

Connector LED RED GREEN AMBER OFF

SFP 2 No SFP module SFP active 100 Mbit/s data rate No Power

Ethernet 1 1 System Error Ethernet active Blinking = Data Connection not active

Ethernet 1 Left Blinking = Data Connection not active

Ethernet 1 Right 100 Mbit/s data rate 10 Mbit/s data rate

Panel Description MiniFlex Dual FOM

Connector LED RED GREEN AMBER OFF

SFP 1 and 2 1 Blinking = Data Connection not active

SFP 1 and 2 2 100 Mbit/s data rate 10 Mbit/s data rate

Ethernet 1 and 2 Left Blinking = Data Connection not active

Ethernet 1 and 2 Right 100 Mbit/s data rate 10 Mbit/s data rate

FlexDSL Telecommunications AG

Steinackerstrassse 31

8902 Urdorf

Switzerland Page 6/6

Tel: +41 44 741 52 90

Fax: +41 44 741 52 93

Email: [email protected]

Web: www.flexdsl.ch

Environment , EMC and Safety

Storage: ETS 300 019-1-1 Class 1.2 (-25°C … +55°C)

Transportation: ETS 300 019-1-2 Class 2.3 (-40°C … +70°C)

Operation: ETS 300 019-1-3 Class 3.2 (-25°C … +70°C)

ETS 300 019-1-3 Class 3.4 When inside an outdoor rack

Higher Operation Temperature range available on request (-25°C … +80°C)

Dimension SHDSL & Single FOM: 143(W)x87(D)x37(H) mm, 153(W)x87(D)x37(H) mm with Clip

Dimension Dual FOM: 143(W)x87(D)x43(H) mm, 153(W)x87(D)x43(H) mm with Clip

Weight < 0.5kg in Metal DIN-Rail Enclosure

Standards: EN 300386 V1.4.1:2008 EN 55024/A2:2003 EN 61000-4-5:2006

EN 50121-4:2006 EN 61000-4-2/A2:2001 EN 61000-4-6:2007

EN 60950-1:2006 EN 61000-4-3:2006 EN 61000-4-6/A1:2001

EN 55022:2006, Class B EN 61000-4-4:2004

Available Models

Ordering Code Interfaces Power Supply Attention!

MF-PAM-RAIL2N-2Eth-24V, V1 2xDSL 2xETH 18-72VDC

MF-PAM-RAIL2N-2Eth-230V, V1 2xDSL 2xETH 110/230VAC

MF-FOM-RAILN-Eth-24V, V1 1xFOM (SFP Cage) 1xETH 18-72VDC

MF-FOM-RAILN-Eth-230V, V1 1xFOM (SFP Cage) 1xETH 110/230VAC

MF-FOM-RAIL2N-2Eth-24V, V1 2xFOM (SFP Cage) 2xETH 18-72VDC

MF-FOM-RAIL2N-2Eth-230V, V1 2xFOM (SFP Cage) 2xETH 110/230VAC

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali FlexDSL Modem

FlexDSL

FlexDSL Orion3 Manuale utente

FlexDSL

FlexDSL ORION 2 Manuale utente

FlexDSL

FlexDSL Orion3 Manuale utente

FlexDSL

FlexDSL ORION 3 Manuale elenco delle parti

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

Paradyne

Paradyne Hotwire 7976 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente