FLIR M-Series Manuale utente
FLIR M-Series and NavNet TZtouch
Overview
The following example illustrates the integration of the FLIR M-Series into a NavNet network. The M-
Series and the JCU controller are set with a fix IP address compatible with NavNet TZtouch. When you
purchase a FLIR (with JCU), it will have a different IP address and will require changes before it is
used with the TZtouch system.
Installation
FLIR Configuration
You have to assign the M-Series and the Controller (JCU), a fixed IP address. We recommend you use
192.168.252.200 / 255.255.255.0 for the M-Series Camera, and 192.168.252.201 / 255.255.255.0
for the JCU (although any IP beginning with 192.168.252.x would work as long as they don’t collide
with any existing IP).
The FLIR M-Series and the JCU controller are UPnP-enabled devices. You can easily see the list of
UPnP-enabled devices from your computer by opening “My Network Places” if using a Microsoft XP
computer or “Network” if using a Vista, Windows 7 or Windows 8 computer. Note that the M-Series
and JCU will only appear on your PC, if they are all on the same network domain.
Normally, the JCU gets its power from the camera when directly connected to the M-Series. When
connecting the JCU to a HUB or Switch, you must use a power injector (48V) to power the unit (see
diagram above).
When the computer is connected to the M-Series Camera and JCU via an Ethernet cable or via a
Hub/Switch (without router or DHCP server on the network), the M-Series and JCU automatically
assign themselves an IP address of 169.254.x.x / 255.255.0.0. In order to access the configuration
page of the M-Series and JCU, you need to setup your PC on that network (ex: 169.254.1.2 /
255.255.0.0)
Note: If your computer is set to “obtain an IP address automatically,” it should automatically set an IP
address of 169.254.x.x from the FLIR after two minutes. However, it is easier to directly fix the PC IP
address at 169.254.1.2 / 255.255.0.0.
Note: If the JCU and the M-Series were previously assigned another IP address, you can display the
JCU IP address by pressing the COLOR button while pushing the puck. You can then assign an IP
address to your PC accordingly, and thus be able to access the M-Series and JCU configuration page.
Once the computer is on the same domain as the M-Series and JCU, and UPnP is enabled, you should
see the M-Series and JCU icon under “My Network Places” (XP) or “Network” (Vista/Windows 7/
Windows 8):
Note: If the devices do not appear, try to restart the M-Series and JCU, then check if your computer is
setup to display UPnP notifications:
xUsing Windows XP:
ͲStart the Control Panel and go to Add/Remove programs
ͲOn the left-hand side, select the Add/Remove Windows components
ͲFrom the Windows Component Wizard, scroll down to Networking Services, then highlight
and select the “Details” button
ͲCheck the box to enable the UPnP User Interface and select Ok
ͲSelect Next when returning to the Windows Component Wizard
ͲSelect Finish
xUsing Windows Vista and Windows 7
ͲTurn on “Network Discovery” on the “Network” page as highlighted below:
CAMERA SETUP:
Double click on the M-SERIES icon to open its configuration webpage. To configure a fixed IP address,
click on “Network Setup”:
Select the Static (fixed) option rather than Dynamic:
The screen will refresh, and the IP, Mask, and Gateway fields will change from grey to white,
indicating they can accept user entries. Once you have entered the appropriate IP address and subnet
mask (192.168.252.200 / 255.255.255.0 in this example), click on the “Save” link and wait 1 minute.
Note: You will not be able to access anymore the M-Series configuration page after changing its IP
address (until you change the IP address of your computer later in this process).
JCU SETUP
Go back to “My Network Places” or “Network” and double click on the JCU icon to open its
configuration page.
Set the Network Addressing to “Static”:
Enter the appropriate IP address and subnet mask (192.168.252.201 / 255.255.255.0) and click on
the “Save”.
FINAL SETUP
After changing the IP address of the M-Series Camera and JCU, change the IP address of the PC
(192.168.252.10 / 255.255.255.0) to confirm that you see the FLIR and JCU icon again in “My
Network Place” (XP) or “Network” (Vista/Windows 7,8).
Note: You may need to restart the Camera and JCU for the Icon to appear in “My Network Place”.
TZtouch Configuration
Press the [HOME] key, the [MENU] button and select [Camera]. Press [Scan] under “FLIR
Installation”:
This should automatically enter the IP address of the M-Series. If the M-Series is correctly detected,
you should see a green light:
IMPORTANT: If the M-Series is not discovered automatically, refer to the appendix (at the end of this
document) to configure the internal M-Series NEXUS server.
Once the FLIR has been detected, select the video input where the analog video output of the FLIR is
connected:
Note: You could connect the analog video output of the M-Series to an AXIS IP video converter. In
that case, you would select the corresponding IP Camera feed in the menu above.
Using an AXIS converter allows the video to be distributed on the network and available on every
TZtouch MFD.
APPENDIX
How to enable the discovery and control of the M-Series from the PC
In some instances, the internal server of the M-Series (“NEXUS” server) is configured in a way that
prevents the PC from discovering it and controlling it. If you are unable to discover the M-Series from
your TZtouch display but are able to use the Web Control of the M-Series to control it via a web
browser on your PC, follow the guide below.
Note: If you are not able to control the M-Series from a Web Browser on your PC, make sure that the
Ethernet connection and IP addresses are correctly setup.
Open a Web Browser and type the IP address of the M-Series: http://<IP ADRESS >.
Example: http://192.168.252.200
Note: To access the Web Server configuration, just type the IP address (do not add any port number)
The Nexus configuration page should appear. Log in as an admin (default password is “indigo”)
Click on “Configuration File”:
Scroll at the very bottom of the page and click on “Download Configuration File”
Save the file somewhere on your computer (on the desktop for example).
Open the configuration file (“server.ini”) with NotePad and look for the section “[Networking
Configuration]”
Set “Enable Network Discovery”, “Enabled” and “Allow Anonymous Clients” to “yes”:
Note: You can search the text file for “Anonymous”, “Discovery” and “Enabled” to find the line you
need to check.
Save the file.
Note: Make sure that you don’t modify anything else.
Go back to the Nexus Configuration page (you might have to log in again), select “Configuration File”
and scroll down to the bottom of the page. Click on “Choose file” and select the “server.ini” file you
just modified. Click on “Upload”.
The FLIR M-Series Nexus server needs to be restarted to take the changes into account.
Go to the very top of the page (header) and click on “Stop”
Wait until the Start button appears, and then click on it.
Your TZtouch display should now be able to detect and control the Camera.
Altri manuali per M-Series
8
Indice
Altri manuali FLIR Macchina fotografica digitale
FLIR
FLIR A6 Series Manuale utente
FLIR
FLIR Scout Manuale utente
FLIR
FLIR ORION SC7000 Manuale utente
FLIR
FLIR Txxx series Manuale utente
FLIR
FLIR USB3 Vision GRASSHOPPER 3 Manuale utente
FLIR
FLIR X-Series Manuale utente
FLIR
FLIR MPX C233BD Manuale utente
FLIR
FLIR Elara FR-345-EST Manuale utente
FLIR
FLIR HS-324 Manuale utente
FLIR
FLIR M-Series Manuale utente
FLIR
FLIR A400 Series Manuale utente
FLIR
FLIR ThermaCAM QuickView Manuale utente
FLIR
FLIR C237BD Manuale utente
FLIR
FLIR A310 ex Series Manuale utente
FLIR
FLIR Exx series Manuale utente
FLIR
FLIR GF300 Manuale utente
FLIR
FLIR Tau Camera TAU-0035-00-10 Manuale utente
FLIR
FLIR Elara FR-345-EST Manuale utente
FLIR
FLIR USB3 Vision CHAMELEON 3 Manuale utente
FLIR
FLIR CP-4221-300 Manuale utente
