FLIR Quasar CM-6405 Manuale utente

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

Quasar™ Mini-Dome

CM-6405 / CM-6408

Quick Install Guide

1 Check Contents

Make sure all of the items above are included in the camera kit.

2 Select a Location

Select a suitable location to mount the camera.

Verify that the operating temperature range is in the following ranges, with no

more than 90% non-condensing humidity:

With heater: -55° C to 60° C (-67° F to 140° F)

Cold start with heater: -55° C to 60° C (-67° F to 140° F)

Warnings

Placing a camera in a surrounding environment subject to extremely high

temperature can result in an explosion or the leakage of flammable liquid or

gas.

Subjecting the camera to extremely low air pressure can result in an explosion

or the leakage of flammable liquid or gas.

The camera must be installed by qualified personnel and the installation

should conform to all local codes.

Be sure to have the required accessories and tools available and refer to the

camera's installation and user guide as necessary.

Cables can enter the camera either through the rear of the camera via the

mounting bracket or through a conduit hole on the side of the camera. If the cables

enter through the rear, make sure that the location provides a suitable method for

routing the cables.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

For further advice on positioning and orienting the camera, see the camera's

installation and user guide.

Supplying Power to the Camera

The camera can be powered by:

A UL-listed L.P.S. (Limited Power Supply) unit, rated to a maximum temperature

of 60° C:

o12 VDC, 1.21A minimum

o24 VAC, 50/60Hz, 1.2A minimum

PoE (Power over Ethernet): 48 VDC, 0.27A minimum

For assistance with purchasing a power supply, contact Teledyne FLIR.

3 Remove Cover and Separate Base

Tip

When unpacking the camera, do not remove the plastic sheet protecting the

dome.

To remove the dome cover:

a. Using the Torx wrench, loosen the screw on the camera's outer circular ring

that secures the dome cover to the camera base.

b. While firmly holding the base, rotate the ring counterclockwise to loosen it.

c. Carefully pull the ring and cover away from the base.

Outer Ring Locking Screw

Loosen Ring

To separate the camera base from the mounting bracket:

a. Using a screwdriver, loosen the two twist-lock screws securing the camera and

its base to the mounting bracket.

b. Gently pull the camera and its base away from the mounting bracket.

Change the number of LEDs (optional)

The camera has a total of eight IR illumination LEDs. On the 3D lens assembly,

there is a 4 / 8 (default) switch that determines the number of enabled IR LEDs.

With the dome cover removed, you can change the switch setting.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

Separate Base from Bracket

4 Connect the Camera

To install the camera, Teledyne FLIR recommends connecting the camera on a

bench or in a lab and configuring it for networking before mounting and aiming it.

However, circumstances can dictate adjusting the sequence of the steps. For

example, you can mount the camera before configuring it for networking, or

connect the camera before mounting it.

Warning

The camera itself does not have a power on/off switch. Do

not supply power to the camera until you have completely

finished connecting it.

Connectors

Connector

Connection

RJ-45

Two LEDs

Attach a Cat 6 cable from the network switch to the RJ45 connector for a

10/100/1000 Mbps Ethernet and IEEE 802.3af class 0 PoE connection.

Ethernet is required for streaming video and for configuring the camera.

The green link LED indicates a good network connection. The orange

activity LED flashes to indicate network activity.

Warning

The PoE unit and all interconnected equipment must be installed indoors within the same

building, including all PoE-powered network connections, as described by Environment A

of the IEEE 802.3af standard.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

Connector

Connection

Four-pin

power

terminal

block

24VAC -

12VDC -

If using a 24VAC or 12VDC power

supply, connect it to the power

terminal block connector according

to the pin assignment shown.

24VAC +

12VDC +

Warning

The power cord to the 12 VDC or 24 VAC power supply unit must be connected to a

socket outlet with an earthing connector.

Default

Button

To restore the camera to its factory defaults, use a proper tool to press

the default button for at least 20 seconds.

USB

Connects to Wi-Fi dongle (future release support)

microSD

Card Slot

For video clip and snapshot recording and file storage, insert a

microSD / SDHC / SDXC card (minimum 8 GB, maximum 512 GB,

Class 10) in the card slot. When the camera is powered on, do not

remove the microSD card.

Nine-pin

terminal

block

Audio In L

Alarm Out +

Attach wires from external devices

to the terminal block connector for

alarm and audio in/out according to

the pin assignment shown.

Audio In R

Alarm Out -

GND

Alarm In +

Audio Out L

Alarm In -

Audio Out R

Warnings

Do not connect an external power supply to the nine-pin audio/alarm I/O

terminal block connector.

This product contains a battery that is soldered to the PCB. There is a risk of

explosion if the battery is replaced by an incorrect type. Do not replace the

battery. The battery should be disposed of in accordance with the battery

manufacturer’s instructions.

Tip

To make it easier to mount and install the camera, while the camera is on the

bench or in the lab, you can connect Ethernet and other cable patch cords to the

camera's connectors and route them through the grommets on the base and

through the mounting bracket. Then, you'll be able to mount and install the

camera without separating the camera base from the mounting bracket a second

time.

5 Configure for Networking

To discover the camera on the network, Teledyne FLIR recommends using the <%

FLIR%> Discovery Network Assistant (DNA) tool. Version 2.3.0.20 or higher

supports Quasar CM-6405 / CM-6408 cameras, does not require a license to use,

and is a free download from the product's web page on the Teledyne FLIR

website. After downloading the DNA ZIP file, extract it.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

You can configure the camera using the DNA tool, the camera's web page, or a

supported VMS.

DNA tool

Camera's web page

Discover camera IP address

•

Configure IP address, mask, and gateway

•

Configure DNS settings, MTU, and Ethernet speed

•

Change user credentials

•

Change video format

•

Configure more than one camera at the same time

•

For information about using the camera's web page to configure the camera, see

the camera's installation and user guide. For information about using a supported

VMS to configure the camera, see the VMS documentation.

By default, DHCP is enabled on the camera and a DHCP server on the network

assigns the camera an IP address. For example, if the camera is managed by

Teledyne FLIR's Horizon or Meridian VMS and the VMS is configured as a DHCP

server, the VMS automatically assigns the camera an IP address.

If the camera is managed by Teledyne FLIR’s Latitude VMS or is on a network

with static IP addressing, you can manually specify the camera’s IP address using

the DNA tool or the camera's web page. The camera's default IP address is

192.168.0.250.

To manually specify the camera's IP address using the DNA tool:

a. Make sure the camera and the PC are on the same LAN segment.

b. Run the DNA tool (DNA.exe) by double-clicking .

The Discover List

appears, showing

compatible

devices on the

LAN segment and

their current IP

addresses.

In the DNA Discover List, verify that the camera's status is Online.

If this is the first time you are configuring the camera or if it is the first time after

resetting the camera to its factory defaults, DNA automatically authenticates

the camera with the default password for the camera's admin user (admin).

If the admin user password has been changed, you need to authenticate the

camera.

In the DNA Discover List, right-click the camera and select Login.

In the DNA - Login window, type the password for the admin user. If you do

not know the admin user password, contact the person who configured the

camera's users and passwords.

Click Login, wait for Ok status to appear, and then click Close.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

In the DNA Discover List, verify that the camera's status is Authenticated.

c. Change the camera’s IP address.

Right-click the camera and select IP Setup.

In the DNA - IP Setup window, clear Use

DHCP and specify the camera's IP

address. You can also specify the Mask

(default: 255.255.255.0) and Gateway.

Then, click Update, wait for Ok status

to appear, and then click Close.

6 Change Video Format (Optional)

By default, NTSC is the camera's video format.

To change the camera's video format to

PAL using the DNA tool:

a. In the DNA Discover List, right-click the

camera and select Change Video Format.

b. In the Change Video Format window,

select PAL.

c. Click Update, wait for Ok status to

appear, and then click Close.

For more information about using the DNA tool to configure one or more cameras,

see the DNA User Guide. While the software is open, click the Help icon

For the camera's other default Video Configuration settings, see 7 Default Video

Configuration Settings.

7 Re-attach Cover

To prevent damaging the camera's internal components while moving it from the

bench or lab to its mounting location, re-attach the dome cover to the base and

then remove it again at the mounting location.

Before doing so, you can re-attach the camera base to the mounting bracket. Use

a screwdriver to tighten the two twist-lock screws securing the camera and its

base to the mounting bracket. If you do not re-attach the camera base to the

mounting bracket, remember to bring the screwdriver to the mounting location.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

To re-attach the dome cover:

a. Using the two guide pins on the dome cover and the triangles on the cover and

on the base, carefully align and position the dome cover onto the base.

b. Securely tighten the outer ring.

c. Lock the ring. Using the Torx wrench, tighten the screw on the outer ring that

secures the cover to the base.

8 Fit Mounting Hardware

If required, install the mounting hardware for the camera according to the

instructions for the hardware.

9 Remove Cover and Separate Base

Repeat the steps described in 4.2 Remove Cover and Separate Base.

10 Install Mounting Bracket

You can install the mounting bracket on standard electrical boxes or directly on a

secure, flush, and vibration-free surface.

To install the mounting bracket on a standard electrical box:

Attach the bracket to the box using:

The holes in the mounting bracket,

according to the types of boxes engraved on

the bracket

The corresponding holes in the box

Suitable bolts, washers, and nuts (not

included in the camera kit)

To install the mounting bracket directly on

a surface:

a. Choose four widely spaced mounting holes

on the bracket for optimum flat surface mounting.

b. Using the bracket as a template to mark the surface, drill four anchor holes.

c. (Optional) If necessary, drill a hole wide enough for routing cables.

d. Hammer the four plastic screw anchors into the drilled holes.

e. Insert the anchors and then attach the bracket to the surface using the four M4

25mm self-tapping screws included in the camera kit.

When tightening the screws, the holes in the mounting plate allow for making small

adjustments to the bracket's position.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

11 Route Cables and Connect the Camera

Cables can enter the camera from the side or from the rear.

To route cables through the side of the

camera:

a. Use the Torx wrench to loosen the

screw securing the side conduit hole

cover and remove the hole cover.

b. Route cables through the hole.

To route cables through the rear

of the camera:

a. Route cables through the hole

in the mounting bracket.

To route cables into the camera base:

a. For each cable, use the Torx wrench to punch a hole in the center of the rubber

glands in the the camera's base, from the underside.

b. Route the cable through the hole in the grommet.

c. Push the cables back through the seal so that the seal extends out of the base.

Inside base

According to the information in 4 Connect the Camera, connect the camera.

Note

Connect the camera to a 24VAC or PoE power source as the primary power

source, and then connect 12VDC as the secondary power source. If the primary

power source fails, the camera seamlessly switches to 12VDC until the primary

power source is restored.

12 Mount and Aim the Camera

a. Make sure that the camera is facing the required field of view. Then, carefully

re-attach the camera base to the mounting bracket. Use a screwdriver to

tighten the two twist-lock screws securing the camera and its base to the

mounting bracket.

b. Aim the camera, which has three axes for adjusting the field of view:

oPan adjustment – Rotate the lens base until satisfied with the field of view.

oTilt adjustment – Loosen the screw locking the camera lens in its tilt angle. Tilt

the lens until satisfied with the field of view. Then, tighten the screw.

oLens rotation – Rotate the 3D assembly in the lens until satisfied with the field

of view.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

Aiming the Camera

Caution

Do not rotate or tilt beyond the mechanical limits for each axis:

Pan adjustment range: 356°

Tilt adjustment range: ±80°

Lens rotation range: ±98° – Rotating the 3D assembly in the lens beyond

its mechanical limit can twist, disconnect, or break the camera's internal

cables.

When adjusting the tilt and lens rotation for a CM-

6408-11-I camera, at the camera's widest view

(zoom = 1x) and at certain tilt angles, as shown

at right, a small part of the camera can appear in

the far upper-left corner of the field of view.

Tilt angle

Lens rotation

angle range

20°

30°~45°

10°

10°~45°

c. Repeat the steps described in 4.6 Re-attach Cover.

13 Complete Camera Setup

Specify the camera's zoom and focus, and format the microSD card, using the

camera's web page. Teledyne FLIR recommends using Microsoft Internet Explorer

11.0, with the ActiveX plug-in.

The camera's web page supports other browsers that do not support ActiveX.

However, using another browser requires configuring MJPEG encoding for at least

one of the camera's video streams; for more information, see the camera's

installation and user guide.

Windows Security dialog box

a. Log in to the camera’s web page.

In the DNA Discover List, double-click the

camera.

In the Windows Security dialog box, type a

user name and password. Both are case-

sensitive.

When logging in to the camera's web page

for the first time or for the first time after

resetting the camera to its factory defaults,

type admin for the user name and for the

password.

CM-6405 / CM-6408 Quick Install Guide Revision 120

December 2021

This document does not contain any export-controlled information.

Then, specify a new password for the admin user. Use a strong password

consisting of 8-64 characters. Passwords can include special characters

@#~!$&<>+_-.,*?.

Log back in using the new password.

b. If the User Account Control dialog opens and prompts you to install the

install.cab file, click Yes.

If ActiveX installation is not successful, in the

Internet Explorer Tools > Internet Options >

Advanced Security settings, select Allow software

to run or install even if the signature is invalid and

click OK. Try installing ActiveX again. After a

successful ActiveX installation, uncheck the

checkbox, and click OK.

If a popup message appears for running the ActiveX add-on, click Allow.

c. Install the web player.

Note

If you have previously installed a web player application on the PC, you

should delete the existing web player from the PC before accessing the

camera. For information on how to install the new player, uninstall a previous

player, and clear temporary Internet files, see the camera's installation and

user guide.

The camera's web page opens.

d. On the Live page, adjust the zoom or focus using the controls.

Altri manuali per Quasar CM-6405

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali FLIR Telecamera di sicurezza

FLIR

FLIR Navigator II Manuale utente

FLIR

FLIR SR-100 Manuale utente

FLIR

FLIR DPB34TLX Manuale utente

FLIR

FLIR FC-Series Istruzioni per il montaggio

FLIR

FLIR FB-Series Manuale utente

FLIR

FLIR SV87-KIT Manuale utente

FLIR

FLIR T4 Series Manuale utente

FLIR

FLIR Raymarine CAM220IP Manuale utente

FLIR

FLIR Lorex LBV2711 Series Manuale utente

FLIR

FLIR DCV64DL Manuale utente

FLIR

FLIR LOREX LNB4321 Series Manuale utente

FLIR

FLIR Quasar CP-6408-21-I Manuale utente

FLIR

FLIR N347VW4 SERIES Manuale utente

FLIR

FLIR Lorex LEV1512 Series Manuale utente

FLIR

FLIR FB-Series Istruzioni per il montaggio

FLIR

FLIR Digimerge DBV44TL Manuale utente

FLIR

FLIR FXV101-H Manuale utente

FLIR

FLIR MPX C234BC Manuale utente

FLIR

FLIR CP-6302-30-R Manuale utente

FLIR

FLIR DBV54TL Manuale utente

FLIR

FLIR FX Manuale utente

FLIR

FLIR C233BC Manuale utente

FLIR

FLIR LOREX LW2770HAC1 Manuale utente

FLIR

FLIR C243MT2 Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente