Fluidmaster EVERYTHING Manuale utente
K-400H-038
‘THE EVERYTHING’TM
3˝ TOILET TANK REPAIR KIT
HOW-TO VIDEO
VISIT: FLUIDMASTER.COM
K-400H-038 PRODUCT PAGE
VIDEO
HELPFUL
TOOLS INCLUDED!
FRENCH - Page 23
*See back page for important product warnings and warranty information.
2
GETTING STARTED
PARTS OVERVIEW
PERFORMAX®FILL VALVE FLUSH VALVE
TOOLS
Rubber Washer (x2)
Stainless Steel Washer (x2)
Large Hex Nut (x2)
Stainless Steel Bolts (x2)
Locknut
Shank
Washer
Rell Tube
Tank Water Level
Adjustment Screw
Bowl Water Level Dial
Rell Clip
Red WrenchGreen Tool
Red Tank-to-Bowl Gasket
Overow Pipe
3” Universal Flapper
Locknut
Tank Lever
3
STEP 1: PREPARE TANK
SEE INSTRUCTION VIDEO ON WEBSITE FOR REFERENCE.
B: DRAIN WATER
Flush toilet to drain most of the water from tank.
FLUSH
A: TURN OFF WATER
HOW-TO VIDEO
VISIT: FLUIDMASTER.COM
K-400H-038 PRODUCT PAGE
4
STEP 2: REMOVE OLD PARTS
A: REMOVE CONNECTOR
Remove water supply connector from
bottom of ll valve by twisting con-
nector nut to the left.
B: REMOVE OLD LOCKNUT
Use green tool to twist locknut to the
left below tank to remove locknut from
ll valve.
C: REMOVE OLD FILL VALVE
Including rell tube, rell clip and
shank washer. Drain any excess
water into the back panel of
empty packaging by removing ll
valve from tank. (Pull ll valve up)
D: DISCONNECT
FLAPPER CHAIN
Towel
(Optional)
NOTE: Inspect water
supply connector. Replace it if
it is worn, or you don’t know
how old it is, to prevent ooding
and property damage.
Green Tool
Tank Lever
E: REMOVE TANK FROM BOWL
Use green tool to twist large hex nut to
the left and remove bolts from tank.
G: REMOVE GASKET
Remove tank-to-bowl gasket from
below the tank.
F: LAY TANK ON ITS SIDE
Place on a safe and secure surface.
H: REMOVE FLUSH VALVE
LOCKNUT
Using red wrench, twist locknut left
to remove. Remove old ush valve
from tank.
5
Screwdriver
(Optional)
Red Wrench
Green Tool
NOTE: Bolts can be
loosened from inside tank.
6
STEP 3: INSTALL FLUSH VALVE
NOTE: Do not cover tank bolt holes with ush valve. If ush valve covers
a bolt hole, turn ush valve slightly to the right (overow tube to the right)
to clear the bolt hole. In some cases, placing bolts in the holes rst may
be necessary.
A: INSERT FLUSH VALVE INTO TANK HOLE
Position overow pipe toward back of tank.
7
STEP 3: INSTALL FLUSH VALVE (CONTINUED)
B: USE RULER ON THE RED WRENCH TO MEASURE
AND ADJUST NEW FLUSH VALVE
Mark the ush valve 1” below bottom of tank lever hole.
NOTE: The top of the overow pipe must be at minimum of 1” below
the tank lever hole.
TOP OF
OVERFLOW PIPE
Overow
Pipe
Lever Hole 1"
BOTTOM OF
TANK LEVER HOLE
Adjusted
Height
C: ADJUST FLUSH VALVE HEIGHT
Twist to unlock, pull or push to correct
height, twist to lock in place.
8
STEP 4: INSTALL TANK-TO-BOWL GASKET
B: Apply red tank-to-bowl gasket to
bottom of ush valve locknut, fully
covering locknut.
Red Wrench
A: INSTALL LOCKNUT
Holding ush valve in place, turn right to screw locknut
onto bottom of ush valve and hand-tighten to secure. Use
red wrench to go ½ turn beyond hand-tight.
Do not overtighten.
9
STEP 5: SECURE TANK TO BOWL
A: INSTALL RUBBER WASHERS
Place one rubber washer on each
tank bolt.
B: INSERT BOLTS INTO TANK
Place tank bolts through bottom
holes of tank.
C: SECURE TANK ONTO BOWL
Set tank onto bowl. Place metal
washer and large hex nut on each
bolt under toilet bowl. Using green
tool, twist right to tighten hex nuts
evenly until tank is snug and does
not rock. Do not overtighten.
Rubber
washer
Rubber
washer
Tank
Metal washer
Large hex nut
Bowl
Green Tool
10
STEP 6: ADJUST FLAPPER
A: REMOVE FLAPPER
Remove apper from ush valve by
pulling the frame of the apper up one
side at a time.
B: ADJUST FOR MOST EFFICIENT FLUSHAdjust from
0 to 10 to nd the perfect ush for your setup.
Hint: The higher the number,
the longer the apper stays
open for more water ushed.
FLAPPER SETTINGS
AMERICAN STANDARD
CATO
ELJER
GERBER
GLACIER BAY
KOHLER
MANSFIELD
ST. THOMAS
PEGASUS
TOTO
VITRA
Cadet 3
Titan
Avalanche
2-Pc High Efficiency
Cimarron
Maverick
Arlington
Palermo
Westminster
Drake
Clayton
Vespin
Corina
8
8
0
6
3
1
5
0
6
9
6
0
6
5
SETTINGBRAND MODEL
Note: Flapper dial is pre-set to maximum setting (10). If toilet model
not listed, keep apper at
default setting 10.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Fluidmaster Prodotto idraulico
Fluidmaster
Fluidmaster FILL 400 3/8" Manuale utente
Fluidmaster
Fluidmaster BETTER THAN WAX 7530 Manuale utente
Fluidmaster
Fluidmaster Flush 550 Foglio di istruzioni
Fluidmaster
Fluidmaster PRO Series Manuale utente
Fluidmaster
Fluidmaster MANSFIELD Manuale utente
Fluidmaster
Fluidmaster S2DBL Manuale utente
Fluidmaster
Fluidmaster PerforMAX K-400H-040 Manuale utente
Fluidmaster
Fluidmaster Delchem Dualflush Manuale utente
Fluidmaster
Fluidmaster PerforMAX K-400H-001 Manuale utente
Fluidmaster
Fluidmaster 540AKR Manuale utente
Fluidmaster
Fluidmaster PerforMAX Manuale utente
Fluidmaster
Fluidmaster FILL 747 3/8 Manuale utente
Fluidmaster
Fluidmaster PerforMAX K-400H-5002 Manuale utente
Fluidmaster
Fluidmaster K-400H-039 Manuale utente
Fluidmaster
Fluidmaster K-507A-008 Manuale utente
Fluidmaster
Fluidmaster MONACO 1000A-002 Manuale utente
