Fluke ClirVu CV200 Manuale utente

CV200, CV300, CV400

CV201, CV301, CV401

ClirVuIR Windows

Installation Guide

PN 4341125

May 2013

Product specications are subject to change without notice.

English

CV200, CV300, CV400

ClirVuIR Window

Installation Guide

Introduction

The ClirVu IR Window is a precision made accessory which, when accurately

surface of a Type 1, 2, 3/12, 3, and 12 enclosures, or as appropriate. All models

are for indoor and outdoor use.

Read and understand these instructions thoroughly before attempting to install

the units.

All of the items in Table 1 are available from Fluke.

Table 1. ClirVu IR Window Models

Series Size Nema Type

CV200 50 mm (2″) 4, 12

CV300 75 mm (3″) 4, 12

CV400 100 mm (4″) 4, 12

PN 4341125

May 2013

43 6

1 2

Introduction

The ClirVu IR Window allows the exibility to inspect an electrical enclosure both

visually and with infrared. Use this accessory on the at surface of a Type 1, 2,

3/12, 3, and 4/12 enclosures, or as appropriate. All models are for indoor and

outdoor use. Table 1 is a list of the models available from Fluke.

Table 1. ClirVu IR Window Models

Model IR Window Size

CV200, CV201 50 mm (2 in)

CV300, CV301 75 mm (3 in)

CV400, CV401 100 mm (4 in)

How to Contact Fluke

To contact Fluke, call one of the following telephone numbers:

●Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)

●Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)

●Canada: 1-800-36-FLUKE (1-800-363-5853)

●Europe: +31 402-675-200

●Japan: +81-3-3434-0181

●Singapore: +65-6799-5566

●Anywhere in the world: +1-425-446-5500

Or, visit Fluke’s website at http://www.uke.com/irwindows.

To view, print, or download the latest manual supplement, visit

http://us.uke.com/usen/support/manuals.

Safety Information

A Warning identies conditions and procedures that are dangerous to the user.

Symbols used on the Product and in this document are in Table 2.

Warning

To prevent damage or injury:

● Read all directions before the installation.

● Comply with local and national safety requirements when working in

hazardous locations.

● Wear appropriate eye and ear protection.

● Check the window for cracks and damage before installation.

● Keep the cover closed and latched except during installation, viewing, or

temperature measurement.

Table 2. Symbols

Symbol Explanation

Risk of danger. Important information. See manual.

Underwriters’ Laboratories, Inc. UL recognized component in North America.

Conforms to requirements of European Union directives.

TYPE 4/12 NEMA Standard. Suitable for indoor/outdoor use.

This product complies with the WEEE Directive (2002/96/EC) marking requirements.

The afxed label indicates that you must not discard this electrical/electronic product in

domestic household waste. Product Category: With reference to the equipment types

in the WEEE Directive Annex I, this product is classed as category 9 “Monitoring and

Control Instrumentation” product. Do not dispose of this product as unsorted municipal

waste. Go to Fluke’s website for recycling information.

�

Before You Start

When your IR Window arrives, unpack the unit. Identify and make sure all the

parts are in the shipment. See Figure 1.

Required tools for installation, see Figure 2:

• Electro-hydraulic hole punch

• Greenlee Punch/Die

• Drilling machine

• Center punch

• Calibrated torque driver

Site Preparation

To prepare the installation site:

1. Mark a pilot hole with the center punch. See Figure 3.

2. Drill a 6 mm (0.2 in) pilot hole with the twist drill.

3. Use a Kwik Stepper drill bit to enlarge the 6 mm (0.2 in) pilot hole to 20 mm

(0.8 in). Or, drill a 10 mm (0.4 in) pilot hole and then enlarge the hole to

22.5 mm (0.875 in) with a Greenlee Punch/Die 71BB. See Figure 4.

4. Select the correct punch/die. See Table 3.

5. Use the Greenlee Punch/Die with the Electro-hydraulic hole punch to make

the hole diameter listed in Table 3. See Figure 5.

Table 3. Tool Selection

IR Window Size Hole Size Greenlee Punch/Die PN

50 mm (2 in) 61.37 mm (2.416 in) 76BB

75 mm (3 in) 89.89 mm (3.539 in) 739BB

100 mm (4 in) 115.42 mm (4.544 in) 742BB

6. Deburr the holes and remove any shavings.

7. Degrease the front panel.

Installation

To install:

1. Insert the IR Window assembly into the punched hole.

2. Align and rmly hold the IR Window in place.

3. Apply a slight amount of torque to each of the four jam-nut screws to break

them loose from the install position.

4. Incrementally tighten each jam-nut screw in a cross-pattern to the torque

recommended in Table 4. This torque makes sure that the frame gasket is

compressed for an optimum seal. See Figure 6.

Note

If a calibrated torque driver is not available, be careful that you do not over

tighten and break the jam-nut screws.

Table 4. Torque Values for Jam-Nut Screws

Model Torque (max.)

CV200, CV201 14 in lb

CV300, CV301 25 in lb

CV400, CV401 50 in lb

Window Door

Close the window door rmly and twist the quarter-turn fastener bail from vertical

to horizontal to latch the door. See Figure 7.

The window is installed and ready for use.

Security Key Conversion Kit

Where security and safety standards require limited access to the window, an

optional Security Key Conversion Kit is available from Fluke. The conversion

kit replaces the standard hand-turn door latch with a door latch that can only be

opened with a key. Two kit sizes are available. See Table 5.

Table 5. Security Key Conversion Kits

Model Description PN

CV200, CV300 Quarter-Turn Stud Conversion Kit 82 4354766

CV400 Quarter-Turn Stud Conversion Kit 85 4354775

To replace a quarter-turn fastener:

1. Use a wire cutter or needle nose pliers to remove the existing retainer.

2. Install the new stud with a new retainer. See Figure 8.

Note

Models CV201, CV301, and CV401 include the security key.

Lifetime Limited Warranty: Infrared Window

This Fluke product will be free from defects in material and workmanship for the lifetime of the product.

“Lifetime” is dened as seven years after Fluke discontinues manufacturing the product, but for at least

ten years from the purchase date. This warranty does not cover damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized

to extend any other warranty on Fluke’s behalf. To obtain service during the warranty period, contact

your nearest Fluke authorized service center to obtain return authorization information, then send the

product to that Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR

A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this limitation of liability may not apply to

you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

03/09

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Sensore di sicurezza

Fluke

Fluke TNT 12000 DoseMate Manuale utente

Fluke

Fluke PRUFTECHNIK DBS30 Manuale utente

Fluke

Fluke PLS SLDR Manuale utente

Fluke

Fluke TS 90 Manuale utente

Fluke

Fluke PLS XLD Manuale utente

Fluke

Fluke LDR Manuale utente

Fluke

Fluke C9970 Manuale utente

Fluke

Fluke Amprobe UAT-620 Manuale di istruzioni

Fluke

Fluke 26500090 Manuale di istruzioni

Fluke

Fluke FiberInspector Pro FI-7000 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente