FLYGT DX Series Manuale utente
1
Doc. :DX
First edition date :12/98
Revision date :
Disassembly and Assembly Instructions
DX SERIES
2
Doc. :DX
First edition date :12/98
Revision date :
DX pump disassembly P. 3
DX pump assembly P. 12
Head components - Exploded view P. 27
DX 35-5, 50-7 spare - Exploded view P. 28
DX 50-11, 50-15 spare - Exploded view P. 29
Electrical connection P. 30
Electrical connection with external panel P. 31
NOTES:
- The pump should be serviced by qualified personnel only, after having been
disconnected from the power mains.
- The DX pump components listed in this manual are accompanied by
identification numbers that refer to the drawings on pages 28 - 29.
- These numbers identify spare parts as listed in our specific catalogue.
- The assembly and disassembly procedure for the DX S versions is the
same.
- The mechanical seal and O-rings should be replace each time you
assemble the pump.
- In the event of damage to the head we recommend that you replace it with
the pre-assembled one (contact our Service Center).
Contents
3
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Place the pump on a clean and
well-lit workbench.
• Loosen the screw in the center of
the head.
4
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Unscrew the three socket head
screws from the head.
• Remove the head as shown in the
picture, using a plasti hammer and
chisel. Be careful not to damage
the head.
5
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Loosen the terminal box screws
and disconnect all the wires, then
remove the capacitor. (18 if any).
• With a socket wrench, loosen the
screws that hold the feet (12).
6
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Remove the suction flange (5).
• Loosen the impeller fastening hex
screw. To secure the impeller,
insert a screwdriver* through the
pumps’ delivery port.
*Not shown in the picture.
7
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Remove the impeller (2); if
necessary, use a pair of pliers. On
the DX 10-15-20 models, retrieve the
impeller lock tab. Remove the V-ring
(24). Loosen the oil chamber
fastening screw (23) and drain the
oil.
• Loosen the stop ring screws (15).
8
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Remove the stop ring and place
the pump in a pan to collect the oil.
(if necessary, prize it out with a
screwdriver).
• Tap the pump body (1) gently with
a rubber hammer to separate from
the shell with wound stator (3).
9
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Remove the shell with stator after
the oil residues have crained.
Remove the fixed part of the
mechanical seal (9) from the pump
body.
• Extract the oil conveyor (10).
10
Doc. :DX
First edition date :12/98
Revision date :
Disassembly
• Use a screwdriver to prize out the
rotating part of the mechanical
seal. Remove the washer
underneath.
• Tap the shaft gently (4) on the
head side, through the hole in the
bearing seat.
Altri manuali FLYGT Pompa dell'acqua
FLYGT
FLYGT MP-3067 Manuale utente
FLYGT
FLYGT Flygt 3069 Manuale utente
FLYGT
FLYGT 3153 Manuale utente
FLYGT
FLYGT 4630 Manuale di manutenzione
FLYGT
FLYGT 3202 Manuale utente
FLYGT
FLYGT SX 5-15 Series Manuale utente
FLYGT
FLYGT 2125 Manuale utente
FLYGT
FLYGT P7030 Manuale utente
FLYGT
FLYGT 3126.290 Manuale utente
FLYGT
FLYGT ITT Flygt Series Manuale utente
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente