foc.us ST-IIIB Manuale utente
P/N 20130320-1
ST-IIIB user manual
Dear customer:
Congratulations on purchasing you new security systeman thank
you for the confidence you have shown in us.You have chosena high
-quality.
Product that has been produced,tested and packed wthegreatest
care.Please familiarize yourself with these instructions before atte
mpting operation will only been sure if it is fitted properly.We hope your
new security system will bring you lasting pleasure.
Brief
User manual
Content
User manual
Chapter I Introduction 1
Chapter 2 Installation and Connection 4
2.1 Installation 4
2.2 Connection(N.O. N.C) 4
2.3 Install wired detector 4
2.4 Intall wereless detector 5
Chapter 3 Keybad and Operation 5
3.1 About panel 5
3.2 Basic operation 7
3.5 Alarm procedure 10
Chapter IV Voice alarm receiving 11
and GSM control
4.1 Remote phone control 11
4.2 Alarm receiving phone operation 11
4.3 GSM remote operation 12
4.4 GSM alarm receiving 12
4.5 GSM control via SMS 12
Chapter IV Voice alarm receiving and GSM control 13
5.1 Set system clock 13
5.2 Set user password 13
5.3 Set voice phone 13
Chapter VI System Setting 14
6.1 Set password 14
6.2 Set CMS number 15
3.3 Flashes when phone line cut 7
3.4 Host arm and disarm 8
6.3 Set voice phone 16
6.4 Set system options 17
6.4.1 Set system clock 17
User manual
6.4.2 Set entry delay 18
6.4.3 Set exit delay 18
6.4.4 Set siren time 18
6.4.5 Set ring times 18
6.4.6 Set detector loss inspection 19
6.4.7 Set arm/disarm tone 19
6.4.8 Set arm/disarm report 20
6.4.9 Set others 20
6.4.9.1Set emergency alarm siren type 20
6.4.9.2 Ac off inspection time setting 21
6.4.9.3 Magnetic contact inspection 21
6.4.9.4 Check wireless detector tamper 21
6.4.9.5 Set force arm 21
6.4.9.7 Set zone alrm times 22
6.4.9.8 Set listen-in time 22
6.4.9.9 Set AC off remind 23
6.5 Manage wireless device 23
6.5.1 Set remote control 23
6.5.1.1 Enroll remote control 23
6.5.1.2 Enter remote control code 24
6.5.1.3 Delte remote control 24
6.5.2 Set detector 24
6.5.2.1 Detector coding 24
6.5.2.2 Enter detector code 25
6.5.2.3 Delete detector 25
6.5.3 Set appliance switch 25
6.5.3.1 Enroll appliance switch 25
6.5.3.2 Delete appliance switch 26
6.5.4 Enroll wireless siren 26
6.5.4.1 Enroll wireless siren 26
6.5.4.2 Delete wireless siren 26
6.6.5 Set door bell 27
6.5.5.1Enroll doorbell 27
6.5.5.2 Delete doorbell 27
6.4.9.6 Set telehpone line disconnect remind 22
User manual
6.6.1 Set zone attribution 28
6.6.2 Set zone siren type 28
6.6.3 Set wired zone loop type 28
29
6.6.4 Set wired zone response speed
6.6.5 Set related zone 29
6.7 System maintance 30
6.7.1 Set timing operation 31
6.7.2 Recording 31
6.7.3 Play recording 31
6.7.4 Set programmable output port 31
6.7.6 Restore to factory default 32
6.7.5 Delete system events 32
6.8 Set GSM module 32
6.9 Advanced setting options 34
6.9.2 Set sever IP address 35
6.9.1 GPRS enable and disable 35
6.9.3 Set sever port 36
6.9.4 Set user ID 36
6.9.5 Set user password 36
6.9.6 GSM SMS language 36
6.9.7 Delay zone tone source options 37
6.9.8 Handshake tone input signal intensity 37
6.9.9 DTMF output signal intensity 37
6.9.10 Set LCD standby brightness 37
6.9.11 Alarm event retain time 38
Chapter VII technical specification 39
7.1 General data 39
7.2 Physical performance 39
Chapter VIII maintenance 40
8.1 Regular test 40
8.2 The cleanliness of control main machine 40
Chapter VX limitation of the products 40
I Alarm mode: with PSTN and GSM network alarm, GSM networ k with
GPRS function(GPRS function is for China market only), remote arm and
disarm panel through CMS or SMS CID protocol, SMS notification, the
priority of PSTN and GSM network is Optional.
With a newlarge-screen, full-touch buttons, LCD graphic displaysteps,
work status,Alarm process easy and intuitive.
The full English voice prompting operation: all local or remote operation,
alarm information, event log view.
4
2
3
GSM-hook and voice telephone with intercom function.
5 All alarm informationcan be programmed for the following settings:
0 does not send any information
1,Send only SMS 2,Only call users 3,SMS + call user 4, CMS only
5 ,CMS + SMS. 6,CMS + call user 7. CMS + SMS + call user
6 Sleep mode: Under sleep mode, all the lights, backlight, voice and
remind tone are disabled.
7 Alarm panel under idle status is equivalent to a cellphone, you can call
through the GSM network for balance inquiries
8 The associated zone: 4 groups associated zone, three kinds of
association patterns, can effectively reduce false alarm or for other
functions.
9 PGM output: With a programmed output port, followed by five kinds of
alarm events output.
10 The doorbell Audio Optional:
1. Ding Dong 2 Welcome 3. Recording 4. Dee-Dee~
11 Remote phone operation:dialing by telephone offsite, after password
verification, you canarm, disarm, listen-in premise, system status query
and electrical switches controls and otheroperations.
12 VoiceAlarm: When panel alarm, it will automatically dial the preset user
phone numbers to report alarm information then you can remote control
the panel afterenter user passwords.
1
User manual
Chapter I Introduction
1.1 Function Introduction
22
23 For CMS
Password access management: the panel has one administrator
password 16 user password, The administrator password primarily for
system administrators to set up the alarm system; The user passwords
for users in the day-to-day use such arm/ disarm,remote operation. The
administrator password, user password can be freely modified.
networking alarm, depending on the number of users, the user
can set four, six or eight usercodes(account number).
2
14 8 wired zones, User can set the circuit type and speed of
response, support N.O, N.C.
15 Enable enroll total 8 wireless remote,8 electronic switch,1 pc of wirele-
ss doorbell and Unlimited for quantity of one way wireless siren.
16 Follow me phone #,two for CMS,four for private alarm receiving.
17 Status inspection function:Enable record and inquiry 120 alarm event
messages.Like the timewhen happens anti-tam per alarm,detector alarm,
tel-line off,arm,disarm,system setting,battery low voltage etc.And also
can inquiry the zone number and alarm type.
18 Timing arm and disarm: 4 sets of timing arm and disarm time.
19 Electrical switches control: User can remote switch on/off via phone or
SMS, also can be controlled manually through the local alarm panel.
20 Zone programmable: factorypreset for each zone type.Users
can modify all the zone type according to the actual needs .
21 Clock: Built-in fullautomatic calendar clock, set to local time
consistent
User manual
13 Wireless zones, each wireless zone can automatically learn the codes
or be coded manually via the keyboard.
24 Zone type identification:After an alarm is triggered, the alarm zone
number displayed on the LCD screen of the panel, also can send the
detailed report toCMS which includes alarm locations andzone types.
25 Al-proof function:If try to cut off the wire between wered detector and
panel or cut off the tel line which.
3
User manual
26 The tampering alarm: cut the cable between wired detectors and the panel
will trigger larm,the telephone line cut will automatically trigger siren alarm.
When someone deliberately dismantled the panel, it will alarm when
triggering tamper switch at the back of the panel.
27 Timing arm/disarm:Enable set 4 group time arm/disarm time.
28 CMS communications test: The panel will send a message to CMS at the
pre-set time interval to inspect the communicaiton if normal.
29 Siren options:Built-in siren, external wired siren, Wirelss siren. All sirens
can be programmedas enabled/disbale when alarms.
30 The voice speakervolume adjustment: adjust the volume bya rotary
switch on the panel.
31 Wireless repeater function:can extend the distance between the detector
and the panel by adding a wireless repeater of our company.
32 The wireless detector low battery prompted:Detectors will send status
report to the panel every 1-3 hours, the corresponding zone number and
the battery voltagesymbol will be displayed on theLCD screen and also
will report toCMS.
2.1
1.
2.
3.
Installation
Fix the bracket to the wall and hang the pane to the bracket
The large metalobjects can not be placed aroundthe panel, so as not to
affect the wireless signal.
Make sure toplace the panel within the wirelessrange of all wireless
accessoris and pay attention to the hidden
2.2 Connection(N.O. N.C)
LINE TELL
DC15V/2A
Power
PGM GND Z33 Z34 GND Z35 Z36 Z37 Z38 GND Z39 Z40
Here only introduce thezone 33, 34, 37, 38. The other zones please
2.3 Install wired detector
2.3.1The wired zones is disabled factory default. when to use wired zones
please enable the zones firstly.When wired zones is in trouble, the
panel will voice prompt "operation fails, Zone trouble if users try
4
User manual
N.ON.C
As pictures
Chapter 2 Installation and Connection
Voice volume
knobs
refer to the above.
Altri manuali per ST-IIIB
2
Indice
Altri manuali foc.us Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente