Focal Point ND-18D1 ES2000 Istruzioni di montaggio

INSTALLATION & USER INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

MODELS COVERED BY THESE INSTRUCTIONS

ND-18D1 ES2000 ELECTRIC STOVE

ELECTRIC STOVE

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not per-

mitted to copy or adapt any of the content without the

prior written permission of Focal Point Fires plc.

Revision E - 05/14

GB IE

Focal oint Fires

Christchurch, Dorset BH23 2BT

Tel: 01202 588 632

Fax: 01202 499326

www.focalpointfires.co.uk

e : info@focalpointfires.co.uk

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 01202 588601 we’re here to help

lines open between 9am and 5pm, onday to Friday

ES2000 Black Electric Stove

The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be located in any

household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future reference and

pass on as necessary to subsequent owners of the appliance.

• DO NOT use this appliance immediately below a fixed socket outlet.

• DO NOT use this appliance in an open flue.

• DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could pres-

ent a hazard.

• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that

will switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.

• CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and

vunerable people are present.

•WARNING: Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less

than 8 years shall only switch on/off the applaince provided that it has been placed or installed in its intended normal operating position and

they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

•WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when

they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar material. A

clearance space of at least one metre should be allowed in front of the appliance.

The electrical socket that the appliance uses UST be easily accessible. Do not route the supply cord directly over or above the heater unit. If

the cord is damaged, it must be replaced by a service agent or competent person.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The appliance is supplied with a pre-wired three pin BS1363 plug plug (13Amp fuse rated) and 1.6 metres of electrical flex. It is

therefore necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The

stove may be installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain

types of floor covering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat

produced by the stove should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should

be mounted on a non-combustible hearth or plinth which extends for at least 150mm in front of the stove.

This appliance should be positioned on a firm level surface. If the stove is to be sited in a fire surround then the suitability of the

surround for use with electrical heaters should be established with the fire surround manufacturer.

If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the risk of draught through the stove

which may cause the safety cut out system in the fan heater to operate.

Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check

that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling

centre.

QUANTITY DESCRI TION

1 Heater

1 User instruction booklet

1.0 IM ORTANT NOTES

I N S TA L L AT I O N & U S E R I N S T R U C T I O N S

GB IE

2.0 INSTALLATION REQUIREMENTS

3.0 A LIANCE DATA

Supply Voltage : 230-240v~50Hz Fuse Rating : 13 Amp

Heating Elements : 2 x 900W Lighting : 2 x G9 25W 230V bulb

Location : Indoor use only Supply plug/cord : BS1363/1.6 metres length

4.0 UN ACKING THE A LIANCE

5.0 COM ONENT CHECKLIST

Section Contents Page No.

1.0 Important Notes 2

2.0 Installation Requirements 2

3.0 Appliance Data 2

4.0 Unpacking the Appliance 2

5.0 Component Checklist 2

6.0 Operating the Appliance 3

Section Contents Page No.

7.0 Safety Cut-Out System 3

8.0 Maintenance 3

9.0 Cleaning 3

10.0 Spares 3

11.0 Servicing 4

12.0 Appliance Dimensions 4

13.0 Guarantee - Terms and Conditions 4

Check that the fan outlet is not covered or obstructed in

any way, and ensure the power to the fire is switched on.

The appliance controls are concealed behind a panel on the

front of the heater.

Switch ‘e’ turns on the flame effect. Knob ‘f’ controls with brightness of the flame effect. Turn knob ‘f’ until the desired effect is

achieved.

Switch ‘b’ controls the fan function. The fan may be operated without heat, or without the flame effect. With the fan running, switch

‘c’ turns on heat setting 1 (900W), and switch ‘'d' controls heat setting 2 (1800W). The fan must be switched on for the heat set-

tings to work. The fan and heating functions can be operated with or without the flame effect. The appliance is fitted with a ther-

mostat. To adjust the thermostat, turn knob ‘a’ until the desired room temperature is achieved.

This appliance has a safety cutout system fitted which will activate if the air inlets or outlets are obstructed. For safety reasons

the fire will NOT switch on again automatically, the following procedure must be carried out before the fire can be operated.

NOTE: The visual effect will remain operational if the cutout is activated, only the fan heater is prevented from working.

Switch OFF the appliance at the wall socket or outlet. Leave the fire OFF for a period of no less than 10 minutes, ensuring all

obstructions are removed. Switch the appliance ON at the wall. Ensure the appliance is turned ON at the control switches. If

the fire fails to operate correctly, repeat the above procedure. If an attempt to switch on the appliance is made before the safe-

ty cutout has reset, the appliance may cutout for a further period of time. If the sequence has been followed correctly and the

appliance still fails to function, check the fuse in the wall outlet. If this is not the cause, call an electrician or maintenance engineer.

ALWAYS DISCONNECT THE A LIANCE FROM THE MAINS SU LY BEFORE

UNDERTAKING ANY MAINTENANCE.

Excluding lamps and fuses, use only genuine spare parts available from your supplier. Replacement lamps must be of the same

wattage and specification as those stated in Section 2.0 Appliance Data.

Replacing the light bulbs.

1) Disconnect the appliance from the mains.

2) Open the door.

3) Remove the three screws at the front of the decorative fuel bed. Remove the fuel bed clamp.

4) Lift up the decorative fuel bed.

5) Two bulbs are located under the decorative fuel bed.

6) Unscrew and replace the bulb(s) using only G9 25W 230V bulb.

7) Re-assembly is the reverse of removal.

There is no specific requirement for care of the fire other than a regular cleaning of the general appliance.

The decorative DF casing is not removable for cleaning. A wipe with a dry cloth is normally sufficient. DO NOT use abrasive

cleaners as they can damage the finish. Brass and silver parts of the fire may be cleaned using a appropriate metal polishes.

Refer to Section 2.0 Appliance Data for lamp and fuse specification. Excluding lamps and fuses, use only genuine manufacturers

spare parts available from your supplier.

6.0 O ERATING THE A LIANCE GB IE

‘a’ ‘b’ ‘c’ ‘d’ ‘e’ ‘f ’

‘a’ Thermostat

‘b’ Fan (without heat)

‘c’ Heat 900W

‘d’ Heat 900W

‘e’ Flame effect on/off

‘f ’ Flame effect dimmer

7.0 SAFETY CUTOUT SYSTEM

9.0 CLEANING

8.0 MAINTENANCE

10.0 S ARES

There are no internal user serviceable parts.

Check regularly for security of wall fixings as appropriate. Also check security of supply cable and connections. If the supply cable

becomes damaged, it must be replaced by a service agent or competent person, such as a qualified electrician.

The wires in the cable are coloured in accordance with the following code:

LIVE - Brown

NEUTRAL - Blue

EARTH - Green/Yellow

Refer to Section 2.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available

from your supplier.

For all Electric fires purchased the 3 year guarantee commences from the date of purchase, providing that you can supply the proof of

purchase. This does not cover consumable items such as pebbles, coals or light bulbs.

Making a claim is easy.

If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then please

submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you can email or

fax. Please note that this does not affect your statutory rights.

Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.

Alternatively email: [email protected].uk or fax. 01202 499326.

Details required:

1. Name, full address including post code and contact telephone number.

2. Receipt of purchase or credit card statement.

11.0 SERVICING GB IE

FIN:

12.0 A LIANCE DIMENSIONS

430 285

540

All dimensions in mm

13.0 GUARANTEE - TERMS AND CONDITIONS

As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifica-

tions without prior notice.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

F860596

Indice

Altri manuali Focal Point Stufa