For-x XC-160.4FD Manuale utente
C L A S S D A M F I
XC-160.4FD
XC-250.4FD
XC-3000.1D
U S E R M A N U A L
INSTALLATION
To achieve optimal performance of your system, please take a
few moments to read over this Owner’s manual before starting
your installation.
POWER CONNECTION
BATT ( 12V POWER )
Before mounting amplifiers, disconnect the negative cable from
the battery to protect any accidential damage to your amplifiers
and audio system. Connect the power cables to power terminal
12V. Amplifiers are not equipped with fuses so that external fuses
should be used. Connect one end of fuse holder to the power
cable going into the amplifiers and the other end of fuse holder to
positive battery. This fuse location will protect the system and the
vehicle against the possibility of a short circuit in the power cable.
Be sure to use fuses and fuse holder adequate for the application.
GND ( GROUND )
Locate a secure grounding connection as close to amplifier as
possible. Make sure the location is clean and provides a direct
electrical connection to the frame of the vehicle. The ground
needs to have as low of a resistance as possible. Connect one
end of a short piece of the same size cable as the power cable to
the grounding point or to one of your batteries or battery bank.
Run the other end of 4 ga cable to the mounting location of the
amplifiers for connection to the amplifiers ground terminals and
connect the ground cable to the GND ( ground terminal ).
REM ( REMOTE )
Run a remote turn on cable from the switched 12V source . This
may be a toggle switch, a relay, your source unit's remote trigger
cables, or power antenna trigger cable. Connect the remote turn
on cable to the REM ( remote ) terminal.
PANEL
(XC-160.4FD / XC-250.4FD)
LOW INPUT
Connect signal cables to RCA Input from headunit.
OUTPUT
RCA to lead signal to another amplifier.
GAIN
Matches output voltage of headunit RCA to input.
X-OVER
Range 50 dk 500 Hz @ 12dB/oct
FILTER SELECTOR SWITCH
Filter may be arranged as High Pass (HPF), Full Range or Low Pass
(LPF)
HIGH PASS FILTER
Controls high pass point for speaker outputs.
LOW PASS FILTER
Controls low pass points of speaker outputs.
BAS CONTROL
0-12 dB / 45Hz
XC-3000.1D
LOW INPUT
Connect signal cables to RCA Input from headunit. Minimum level
shall be 0.2V.
GAIN
Matches output voltage of headunit RCA to input.
SUBSONIC FILTER
Controls High Pass Points of speaker to prevent excessive low
frequency.
LOW PASS FILTER
Controls Low Pass Filter of speaker output
REMOTE LEVEL CONTROL
Connects to external level control.
REMOTE CONTROL
Turn the switch clockwise for higher level and turn the switch
counter clockwise for lower level.
MASTER OUTPUT / SLAVE INPUT
Minimum impedance is 2 for the same 2 amplifiers connection. In
this mode, main amplifier shall control gain settings of connected
amplifier.
POWER PROTECTION
Blue color LED means correct operation. Red color LED means
general fault, incorrect connection or termal protection
+12V(B+), GND, REM
XC-160.4FD
XC-250.4FD
XC-3000.1
GND (GROUND CONNECTION)
To connect chassis to the ground 4 gauge cable is recommended
for optimum performance. 0 gauge is recommended for XC-
160.4FD, XC-250.4FD, XC-3000.1D.
REM (Remote Control)
Connect to +12V switched from head unit.
+12V/B+ (Power Connection)
Connects to positive side of acumulator (+12). 4 gauge cable is
recommended for XC-160.4FD and XC-250.4FD in order to best
performance. 0 is recommended for XC-3000.1D.
Speaker Outputs
For speaker – amfi connection, speaker cable shall be minimum 12
gauge. For one unit minimum empedans is 1 (XC-3000.1D & XC-
250.4FD). Minimum empedans is 2 (XC-160.4FD)
POWER PROTECTION
Blue color LED means correct operation. Red color LED means
general fault, incorrect connection or termal protection.
ATTENTION
Following steps shall be followed for mounting of amplificator.
1. Make sure that the ground is proper, then connect
amplificator.
2. Next step is to connect +12V cable; make sure that all power
terminals is being used. For security, this cable shall be
integrate in acumulator.
3. Final step is to connect switched remote control.
+12V (B+), GND, REM CONNECTION
(XC-160.4FD)
(XC-250.4FD)
ATTENTION
The ground should be at equal distance. This drawing is just for an
example.
12 AWG speaker cable is recommended for reaching required
performance.
Connect 12 AWG speaker cable to amplifier’s mounting area.
Keep speaker cables seperate from power cables and
amplificator input cables. Use tabs at the locations where cables
need to be connect to vehicle chassis. Connect speaker cables
as per terminal of each speaker. Peel the isolation of each cable
for 1 cm and connect cables to eachother. Connect cable ends
to amplificator as shown on connection schedule.
+12V (B+) GND, REM Connection
(XC-3000.1D)
The ground should be at equal distance. This drawing is just for an
example.
12 AWG speaker cable is recommended for reaching required
performance.
Connect 12 AWG speaker cable to amplifier’s mounting area.
Keep speaker cables seperate from power cables and
amplificator input cables. Use tabs at the locations where cables
need to be connect to vehicle chassis. Connect speaker cables
as per terminal of each speaker. Peel the isolation of each cable
for 1 cm and connect cables to eachother. Connect cable ends
to amplificator as shown on connection schedule.
SPEAKER CONNECTION
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali For-x Amplificatore
For-x
For-x XQ-500.1D Manuale utente
For-x
For-x MAESTRO-8DSP Manuale utente
For-x
For-x MAESTRO-1 Manuale utente
For-x
For-x MAESTRO-812DSP-DSD Manuale utente
For-x
For-x XAQ-4.80SQ Manuale utente
For-x
For-x XQ-48DSP Manuale utente
For-x
For-x XD-180.2 Manuale utente
For-x
For-x XC Series Manuale del proprietario
