Formosa MIMO WiTDM Series Manuale utente

MIMO WiTDM

Series

KW50-O8500

User’s Manual

2017/11/02 v2

There is no any clear or implicit assurance in the user's manual of our company, including the

assurance of selling or installing for the special purpose. There are rival's volumes to carry on the

power to alter or revise in our company, if alter and forgive me for not issuing a separate notice. You

can’t duplicate any content of this manual by the written permission of our company.

About this manual

The purpose to use this manual is for install the wireless Bridge. This manual is including

disposing course and method and helping the customer to solve the unpredictable problem.

The following typographical conventions are used in this purpose:

 Notice:

 This indicates an important Note.

Caution:

 This indicates a warning or caution

Bold Type：Indicates the function, important words, and so on.

Index

CHAPTER 1 INTRODUCTION ............................................................................................................................................ 4

INTRODUCTION ....................................................................................................................................................................... 4

APPEARANCE OF PRODUCT ..................................................................................................................................................... 4

FEATURES AND BENEFITS ....................................................................................................................................................... 4

CHAPTER 2 HARDWARE INSTALLATION ..................................................................................................................... 5

SYSTEM REQUIREMENT .......................................................................................................................................................... 5

PRODUCE KIT ......................................................................................................................................................................... 5

HARDWARE INSTALLATION ..................................................................................................................................................... 5

LED DESCRIPTIONS ............................................................................................................................................................... 5

CHAPTER 3 SYSTEM SETUP .............................................................................................................................................. 6

FACTORY DEFAULT SETTINGS ................................................................................................................................................. 6

USING THE WEB MANAGEMENT ............................................................................................................................................. 7

STATUS ................................................................................................................................................................................... 8

MAP .................................................................................................................................................................................... 10

SYSTEM ................................................................................................................................................................................ 11

CHAPTER 4 WIRELESS SETTINGS ................................................................................................................................ 15

BASIC WIRELESS SETTINGS .................................................................................................................................................. 15

CHAPTER 5 MANAGEMENT ............................................................................................................................................ 19

CHANGE PASSWORD ............................................................................................................................................................. 19

UPGRADE FIRMWARE ........................................................................................................................................................... 21

BACKUP/RESTORE ................................................................................................................................................................ 22

EVENT LOG .......................................................................................................................................................................... 23

REBOOT ................................................................................................................................................................................ 23

CHAPTER 6 TROUBLESHOOTING ................................................................................................................................. 24

FAQ ..................................................................................................................................................................................... 24

SERVICE SUPPORT ................................................................................................................................................................ 25

Chapter 1 Introduction

Introduction

Thank you for choosing the Formosa’s KW50-O8500 Wireless Outdoor MIMO WiTDM Bridge. It is a PoE

power supply, waterproof, and dust-proof wireless bridge that is specially designed for connecting among

multiple network location. The KW50-O8500 work on 5GHz, and it based on powerful TDMA technology that

provides higher channel bandwidth for long distance connect.

Appearance of Product

KW50-O8500

 Features and Benefits

 Support Power over Ethernet (PoE)

 IP68 class of enclosure

 Support TDMA mechanism, to ensure quality for multi-media application

 Easy to install and friendly to user, just plug and play.

 Provides Web-based configuration utility.

Chapter 2 Hardware Installation

System Requirement

Installation of MIMO WiTDM® outdoor unit of KW50-O8500 system requirement:

Two PCs with automatic speed control NIC support the transfer rate of 10/100/1000 Mbps data.

 The IP address of NIC should be the same subnet with the AP, the default IP address of AP is 192.168.1.1

 Microsoft Internet Explorer 6 or above.

Produce Kit

 KW50-O8500 x 1

 Injector-GT3 (48V, 0.65A) x 1

 Mounting Kit x 1

 User’s Manual CD x1

Hardware Installation

The following steps will help you while installing MIMO WiTDM®.

LED Descriptions

LED Status Description

Power Green Power ON

STATUS Green Power on Flash 1 Sec , then OFF

Remote

RSSI Green

CPE：Go around while surveying ( not connect yet ),

Represent strength of RSSI after connected.

Low ( 1 LED ) → High ( 5 LEDs )

RST Push 5 seconds then release to reset device to default

LED Definition

Chapter 3 System Setup

Factory Default Settings

We’ll elaborate the KW50-O8500 factory default settings. You can re-acquire these parameters by default. If

necessary, please refer to the “Restore Factory Default Settings”.

Item Factory Default

User Name admin

Password password

Basic Settings

Device Name DEVICExxxxxx (xxxxxx Represent the last 6

digitals of the MAC address)

Ethernet Data Rate Automatic

Spanning Tree Protocol Enable

VLAN (802.1Q) Disable

IP Settings

IP Type：Manual

IP Address：192.168.1.1

IP Subnet Mask：255.255.255.0

Default Gateway：0.0.0.0

Primary DNS Server：0.0.0.0

Secondary DNS Server: 0.0.0.0

Time Settings

Time Server: None

Time Sever Port: 123

Time Zone: (GMT-08:00)Pacific Time(US &

Canada);Tijuana

Wireless Setup

Radio Frequency (RF) Enable

Operation Mode Base Station

Network ID Wireless

Time Slot 10ms

RF Bandwidth 20MHz

Channel / Frequency 5060 MHz

Data Rate SS BPSK 1/2 – SS 64QAM 5/6 , SS BPSK 1/2 – DS

64QAM 5/6

Output Power Full

Default Settings

Using the Web Management

The KW50-O8500 provides you with user-friendly Web-based management tool.

Open IE and enter the default IP address (Default: 192.168.1.1) and Login as below：

Enter the username (Default: admin) and password (Default: password) and click “Login”

 Caution：

 IP address of your PC must be the same subnet of device

After login, you can check basic information of device, such as MAC address off device, Firmware version, etc.

Device Information

Status

Select Status, you will get the information as below,

Status

System: This field identifies the current time and Coordinates.

GPS: GPS Satellites Information (Only for GPS Model)

Wireless:

MAC Address: MAC of Remote MIMO WiTDM Bridge.

IP Address: IP of Remote MIMO WiTDM Bridge.

Local RSSI: RSSI of Local Bridge.

Remote RSSI: RSSI of Remote Bridge.

Tx/Rx Rate: Current Data Rate of Tx/Rx.

Tx/Rx Modulation: Current Modulation of Tx/Rx.

How to Setup MIMO WiTDM Bridge

Get Position, Longitude and Latitude

Get Direction and Azimuth

Signal Status, In Status page, it can show remote bridge Signal Strength for local bridge (Local RSSI) and local

bridge Signal Strength for remote bridge (Remote RSSI). We can decide the best direction of antenna from

following steps:

1. We check the Local RSSI only in one side. (We call it local side.)

2. Fix remote side antenna, and adjust local side antenna. In local side, check the “Local RSSI” first, to

find a best Local RSSI and then fix the local antenna.

3. Adjust the Remote antenna, to find the Best Remote RSSI, and then fix the remote antenna.

4. If “Local RSSI” is changed, and worse than before, adjust local antenna again to get a best one and fix

local antenna.

5. If “Remote RSSI” is changed and worse, adjust remote antenna again.

6. Follow the same ways to get a better Local RSSI and Remote RSSI value. And Fix both side antennas.

Port Statistic:

Display Wireless and Ethernet statistics of packets including transmitted and received packets, Unicast, Broadcast,

Multicast and total Packets. Click “Refresh” can get instant information.

MAP

Global Positioning System, GPS (Only for GPS Model)

Select GPS, Can obtain current position from GPS receiver.

Topology

Select Topology, Can enable topology discovery protocol to establish the structure of connections.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente