Fortinet FortiGate FG-80C Manuale utente

Description of Issue

Due to an incorrect partition of the flash storage device, the FortiGate 80C may fail to boot-up. The

flash disk capacity should be 7640MB in size, devices that report a flash disk size of 7636MB have a

hidden partition (4MB) which may prevent the FortiGate from booting up if it attempts to locate the

operating system image in this partition.

The FortiGate models that may be affected by this issue are as follows:

FG-80C (PN: P05403-05-xx or higher)

FG-80CM (PN: P05446-05-xx or higher)

FW-80CM (PN: P05405-06-xx or higher)

To identify the part number (PN) of a specific unit, either;

1) Check the label on the bottom of the unit

2) Use the “get system status” command from the CLI

The part number of a device can be identified using the following CLI command:

FGT80C3900000000 # get system status

*************

Serial-Number: FGT80C3900000000

*************

System Part-Number: P05403-05

If your FortiGate is within the affected part number range you can verify the flash disk size to know if

it is correct or if there is a hidden partition that may cause the device to fail to boot-up. Upon boot-

up the flash size may be reported

Boot up, boot device capacity: 4MB --- Incorrect, the device will not boot

Boot up, boot device capacity: 7636MB --- Incorrect

Boot up, boot device capacity: 7640MB --- Correct

Resolution

This issue can be corrected and prevented from occurring by re-formatting the flash file system and

removing the hidden partition. This operation will take approximately 10 minutes to perform,

FortiGate console access and a local TFTP server are required, the basic procedure is similar to

loading an HQIP test image, during the operation the device will be out of service.

Following are the detailed steps and procedures required to perform the re-formatting, the main

components required for these upgrade steps are:

• Console access to the FortiGate

• TFTP server connected to port internal1 of the FG80C

• Disk format image

• Desired FortiOS image

Instruction Steps

Ensure configuration back-ups are taken before any format procedures are started.

1) Download the required format images

Depending upon the hardware model type the following format images will be required:

FortiGate FG80C - FGT_80C-FORMAT.3.0.0.1001.out

FortiGate FG80CM - FGT_80CM-FORMAT.3.0.0.1012.out

FortiWiFi FW80CM - FWF_80CM-FORMAT.3.0.0.1001.out

The images may be downloaded from:

ftp://ftp-temp:r3triev3@support.fortinet.com/CustomerCare/FGT_80C-FORMAT.3.0.0.1001.out

ftp://ftp-temp:r3triev3@support.fortinet.com/CustomerCare/FGT_80CM-FORMAT.3.0.0.1012.out

ftp://ftp-temp:r3triev3@support.fortinet.com/CustomerCare/FWF_80CM-FORMAT.3.0.0.1001.out

2) Set-up a TFTP server for image upload

A suggested TFTP server is available from solar winds, others may also work correctly:

http://www.solarwinds.net/Tools/Free_tools/TFTP_Server/download.htm

a) Save the image to the TFTP root folder, example as follows:

C:\TFTP-Root\ FGT_80C-FORMAT.3.0.0.1001.out

b) Save the desired FortiOS image to the root folder, example as follows:

C:\TFTP-Root\ FGT_80C-v400-build0656-FORTINET.out

Any external USB drive must be removed from the USB port, otherwise the open-card program may

fail to function properly!

For more information on how to setup ftp server and terminal client, please check following KB

article:

http://kb.fortinet.com/kb/microsites/microsite.do?cmd=displayKC&docType=kc&externalId=10338&

sliceId=1&docTypeID=DT_KCARTICLE_1_1

3) Load pre-format image

a) When the download completes, the console displays a message similar to:

Save as Default firmware/Run image without saving:[D/B/R]

b) Press R.

c) The system will start and open card mode selection menu will appear:

Opencard Mode Selection Menu:

[1] Pre-Format

[2] F1-Format

[3] GetInfo

d) Enter selection 1 for pre-format

e) Upon completion “Preformat succeeded” will be displayed

Below is a sample console output for the pre-format image loading when following the above steps:

FortiGate-80C (16:50-09.27.2011)

Ver:04000009

Serial number: FGT80C3910000000

RAM activation

Total RAM: 1024MB

Enabling cache...Done.

Scanning PCI bus...Done.

Allocating PCI resources...Done.

Enabling PCI resources...Done.

Zeroing IRQ settings...Done.

Verifying PIRQ tables...Done.

Disabling local APIC...Done.

Boot up, boot device capacity: 7636MB.

Press any key to display configuration menu...

[G]: Get firmware image from TFTP server.

[F]: Format boot device.

[B]: Boot with backup firmware and set as default.

[I]: Configuration and information.

[Q]: Quit menu and continue to boot with default firmware.

[H]: Display this list of options.

Enter Selection [G]:

Enter G,F,B,I,Q,or H: G

Please connect TFTP server to Ethernet port "1".

Enter TFTP server address [192.168.1.168]:

Enter local address [192.168.1.188]:

Enter firmware image file name [image.out]: FGT_80C-FORMAT.3.0.0.1001.out

MAC:00090F4660A2############

Total 13588979 bytes data downloaded.

Verifying the integrity of the firmware image.

Total 65536kB unzipped.

Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]? R

................................................................

Reading boot image 3954827 bytes.

Initializing firewall...

System is started.

Opencard Mode Selection Menu:

[1] Pre-Format

[2] F1-Format

[3] GetInfo

Enter selection [1, 2, or 3]: 1

ISP started, please wait...

Preformat succeeded!

4) Load and format F1 image

Power OFF the unit, wait for five (5) seconds and power ON again, reload the format image as in step

3 and choose "R" to run the image for next step F1-format as detailed below.

a) The system will start and open card mode selection menu will appear:

Opencard Mode Selection Menu:

[1] Pre-Format

[2] F1-Format

[3] GetInfo

b) Enter selection 2 for F1-format

c) Upon completion “F1 format succeeded” will be displayed

Below is a sample console output for the F1 format image loading when following the above steps:

FortiGate-80C (16:50-09.27.2011)

Ver:04000009

Serial number: FG80C3910000000

Technical Service Bulletin

RAM activation

Total RAM: 1024MB

Enabling cache...Done.

Scanning PCI bus...Done.

Allocating PCI resources...Done.

Enabling PCI resources...Done.

Zeroing IRQ settings...Done.

Verifying PIRQ tables...Done.

Disabling local APIC...Done.

Boot up, boot device capacity: 7000MB.

Press any key to display configuration menu...

[G]: Get firmware image from TFTP server.

[F]: Format boot device.

[B]: Boot with backup firmware and set as default.

[I]: Configuration and information.

[Q]: Quit menu and continue to boot with default firmware.

[H]: Display this list of options.

Enter Selection [G]:

Enter G,F,B,I,Q,or H: G

Please connect TFTP server to Ethernet port "1".

Enter TFTP server address [192.168.1.168]:

Enter local address [192.168.1.188]:

Enter firmware image file name [image.out]: FGT_80C-FORMAT.3.0.0.1001.out

MAC:00090F4660A2############

Total 13588979 bytes data downloaded.

Verifying the integrity of the firmware image.

Total 65536kB unzipped.

Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]? R

................................................................

Reading boot image 3954827 bytes.

Initializing firewall...

System is started.

Opencard Mode Selection Menu:

[1] Pre-Format

[2] F1-Format

[3] GetInfo

Enter selection [1, 2, or 3]: 2

Platform: FG80C

F1 format succeeded.

-------------------- Device Information --------------------

Unit: sector

SDK version=v04.00.01

Date=2013.01.09 Time=17:00

SN=0700319140FFFF00 Manufacture Name=FORTINET

VID=13FE Product Name=80C_G2_FWV071610

PID=3100 Inquiry Product Name=80C_G2_FWV071610

Inquiry Version=1610 TSB-130313-1 Fortinet 8

Technical Service Bulletin

Inquiry Manufacturer=FORTINET

F/W Version=07.16.10 FirmwareType=0xFF01

CDROMSize=0 PublicSize=14336000

SecureSize=0

Normal HiddenSize=0 IsExisted Firmware code=1

IsExisted PWS Private=0 IsLogin Private=0

iController_ID=2233 iMode=3

--------------------------------------------------------

total capacity:14336000 sectors, 7000 MB

All done.

Congratulations! Opencard process succeeded. The device is ready to use now.

Opencard Mode Selection Menu:

[1] Pre-Format

[2] F1-Format

[3] GetInfo

Enter selection [1, 2, or 3]:

5) Load desired FortiOS image (4.0MR3 patch 12 in this example)

a) After the F1 format completes,power OFF the unit, wait for five (5) seconds and power ON again.

b) During boot-up sequence press any key to display configuration menu.

c) Using the TFTP upload procedure in step 3) load FortiOS 4.0MR3 patch 12 image to the FortiGate

flash.

If all the above steps have been completed without error the FortiGate FG80C has been successfully

re-formated to prevent the potential boot failure issue from occurring. For further assistance please

contact your local Fortinet technical support center.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fortinet Firewall

Fortinet

Fortinet FortiGate FortiGate-1000A Manuale utente

Fortinet

Fortinet FortiGate-80C Manuale utente

Fortinet

Fortinet FortiGate FortiGate-50R Manuale dell'operatore

Fortinet

Fortinet FortiGate 5020 Manuale utente

Fortinet

Fortinet FortiGate 60M Manuale utente

Fortinet

Fortinet FortiGate 500 Manuale dell'operatore

Fortinet

Fortinet FortiGate 3810A-LENC Manuale utente

Fortinet

Fortinet FortiGate-200A Manuale utente

Fortinet

Fortinet FortiGate FortiGate-5050 Manuale utente

Fortinet

Fortinet FortiGate-60 series Manuale di istruzioni

Fortinet

Fortinet FortiGate FortiGate-5001FA2 Manuale utente

Fortinet

Fortinet FortiNDR 3500F Manuale utente

Fortinet

Fortinet FortiGate-400A Manuale utente

Fortinet

Fortinet FortiGate FortiGate-5005-DIST Manuale utente

Fortinet

Fortinet FortiAnalyzer-2000B Manuale utente

Fortinet

Fortinet FortiGate-100 Manuale utente

Fortinet

Fortinet FortiGate FortiGate-500A Manuale di istruzioni

Fortinet

Fortinet FortiGate ASM-FX2 Manuale utente

Fortinet

Fortinet FortiAnalyzer-2000 Manuale utente

Fortinet

Fortinet FortiGate FortiGate-5001 Manuale di istruzioni

Fortinet

Fortinet FortiGate FortiGate-300A Manuale utente

Fortinet

Fortinet FortiGate 100A Manuale di istruzioni

Fortinet

Fortinet FortiManager-3000B Manuale utente

Fortinet

Fortinet FortiGate-200 Manuale utente

Manuali Firewall popolari di altre marche

Cisco

Cisco S190 Manuale utente

ADTRAN

ADTRAN NetVanta 2300 Manuale utente

SecureLogix

SecureLogix ETM System Manuale utente

NETGEAR

NETGEAR ProSafe FVX538 Manuale utente

Lanner

Lanner FW-8877 Manuale utente

Huawei

Huawei USG6000 Series Manuale di installazione e funzionamento

H3C

H3C SecPath F5000-AI-15 Manuale utente

Nexcom

Nexcom DNA 1150 Manuale utente

Cisco

Cisco 3110 Manuale

Draytek

Draytek Vigor2860 Series Manuale utente

Lanner electronics

Lanner electronics FW-7650 Series Manuale utente

Swisscom

Swisscom Internet Backup Manuale utente

SonicWALL

SonicWALL NSa 5700 Manuale utente

DPtech

DPtech FW1000 SERIES Manuale utente

FEITIAN

FEITIAN MultiPass FIDO Manuale utente

EBLOCKER

EBLOCKER PRO Manuale utente

GTA

GTA GB-200 Manuale utente

Trend Micro

Trend Micro Deep Edge Manuale utente