FOS Technologies FOS Glow Manuale utente

FOS Glow

Thank you for choosing our products. For your own safety, please read this manual before

installing the device. This manual contains important information on installation and applications.

Please install and operate the fixture with following instructions, make sure the power is off

before opening the light or repairing. Meanwhile, please keep this manual well for future needs.

It is made of a new type of high temperature strength of engineering plastics and cast aluminum

casing with nice outlook. The fixture is designed and manufactured strictly following CE standards,

complying with international standard DMX512 protocol. It’s available independently controlled

and linkable with each other for operation. And it is applicable for large-scale live performances,

theater, studio, nightclubs and discos.

Safety Instructions

This device has left the factory in perfect condition. In order to maintain this condition and to

ensure a safe operation, it is necessary for the user to follow the safety instructions

and warning notes written in this user manual. If the device has been exposed to temperature

changes due to environmental changes, do not switch it on immediately. The arising condensation

could damage the device. Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore, it is essential that the device be earthed.

Note: Damages caused by disregard this manual are not subject to warranty. The dealer will not

accept liability for any resulting defects or problems.

The electric connection must carry out by qualified person. The device shall only be used with

rate voltage and frequency. Make sure that the available voltage is not higher than stated at the

end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If

this would be the case, replacement of the cable must be done by an authorized dealer. Always

disconnect from the mains, when the device is not in use or before cleaning it. Only handle the

power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up

some smoke or smell may arise. This is a normal process and does not necessarily mean that the

device is defective, it should decrease gradually. Please don't project the beam onto combustible

substances. Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for

heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be

exclusively replaced by the manufacturer or his service agent or a similar qualified person in order

to avoid a hazard.

Key Features

•Power supply: AC110-240V 50/60Hz

•Power consumption: 80w

•Source: 8x3w led warm white, 8x3w led red laser, 638nm_500mw

•LED working lifetime:50000 hours

•Color temperature: 3200k

•Channel: 7/9/18/24 four channel mode

•Laser Pattern: Single thick beam for each laser output

•Control mode: DMX-512 signal control, auto mode, sound, control mode.

•Cooling system: fan forced cooling system

•Working environment: indoor

•Fixture size: 1070 x 80 x 68 mm

•Packing size (1in1）: 1150 x 160 x 260 mm

•Net Weight: 8.3kg, Gross Weight: 9.5kg

•Packing size（2in1）: 1200 x 390 x 290 mm

Operation Instructions

•The moving head is for laser purpose.

•Don’t turn on the fixture if it’s been through severe temperature difference like after

transportation because it might damage the light due to the environment changes. So,

make sure to operate the fixture until it is in normal temperature.

•This light should be kept away from strong shaking during any transportation or

movement.

•Don’t pull up the light by only the head, or it might cause damages to the mechanical

parts.

•Don’t expose the fixture in overheat, moisture or environment with too much dust

when installing it. And don’t lay any power cables on the floor. Or it might cause

electronic shock to the people.

•Make sure the installation place is in good safety condition before installing the fixture.

•Make sure to put the safety chain and check whether the screws are screwed properly

when installing the fixture.

•Make sure the lens is in good condition. It’s recommended to replace the units if there

are any damages or severe scratch.

•Make sure the fixture is operated by qualified personnel who knows the fixture before

using.

•Keep the original packages if any second shipment is needed.

•Don’t try to change the fixtures without any instruction by the manufacturer or the

appointed repairing agencies.

•It is not in warranty range if there are any malfunctions from not following the user

manual to operate or any illegal operation, like shock short circuit, electronic shock,

lamp broke, etc.

Display Menu

Addre 001-512 512 address setting

Chnd 07CH 07CH settings

09CH 09CH settings

18CH 18CH settings

24CH 24CH settings

Slnd Auto Auto mode

Sound Sound mode

Slve 1 Console mode

Slve 2 Auxiliary machine

Shnd Sh 0-9 Effect 0 - Effect 9

Auto Speed 0-100 Auto speed

Sound Sense 0-100 Sound sensitivity

Nodmx Set Blac No 512 signal to

Auto No 512 signal Auto

Sound No 512 signal

LED OFF Open off the screen

ON Close off the screen

Disp Yes Turn off the display

ON Turn on the display

RPan OFF X motor is turning

ON X motor reversal

Rest YES System reset

DMX Charts

7 Channels

CH DMX Value Function

1 0-255 X motor operation

2 0-255 X motor speed

3 0-255 0-255 overall

0-127

LED Auto built-in

128-255 LED sound control

5 0-127 Auto built-in effect

128-255

Sound control built-in

6 128-255 Speed/sound

7 128-255 Reset

9 Channels

CH DMX Value Function

1 0-255 X motor operation

2 0-255 X motor speed

3 0-255 Overall brightness

4 0-255 Strobe speed

5 0-255 Laser Auto effect

6 0-255 Laser Auto speed

7 0-255 LED Auto effect

8 0-255 LED Auto speed

9 250-255 Reset

18 Channels

CH DMX Value Function

1 0-255 X motor operation

2 0-255 X motor speed

3 0-255 BAR1 brightness

4 0-255 BAR2 brightness

5 0-255 BAR3 brightness

6 0-255 BAR4 brightness

7 0-255 BAR5 brightness

8 0-255 BAR6 brightness

9 0-255 BAR7 brightness

10 0-255 BAR8 brightness

11 0-255 Group 1 white bright

12 0-255 Group 2 white bright

13 0-255 Group 3 white bright

14 0-255 Group 4 white bright

15 0-255 Group 5 white bright

16 0-255 Group 6 white bright

17 0-255 Group 7 white bright

18 0-255 Group 8 white bright

24 Channels

DMX Value

Function

0-255

X motor operation

0-255

X motor speed

0-255

Overall brightness

0-255

BAR1 brightness

0-255

BAR2 brightness

0-255

BAR3 brightness

0-255

BAR4 brightness

0-255

BAR5 brightness

0-255

BAR6 brightness

0-255

BAR7 brightness

0-255

BAR8 brightness

0-255

Group 1 white bright

0-255

Group 2 white bright

0-255

Group 3 white bright

0-255

Group 4 white bright

0-255

Group 5 white bright

0-255

Group 6 white bright

0-255

Group 7 white bright

0-255

Group 8 white bright

0-255

Strobe speed

0-127

LED Auto built-in

128-255

LED sound control

0-127

LED Auto built-in

128-255

Sound control built-in

0-127

Speed/sound

128-255

Reset

Maintenance and Cleaning

The following points must be considered during the inspection:

1. All screws for installing the devices or parts of the device must be tightly connected and must not be

corroded.

2. There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling,

suspension, trussing).

3. Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.

4. The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage must be adhered by a skilled installer

and any safety problems must be removed.

Note: Disconnect mains before starting maintenance process!

In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the

lights.

•Clean the inside and outside lens each week to avoid the weakens of the lights due to accumulation

of dust.

•Clean the fan each week.

•A detailed electric check by approved electrical engineer each three month, make sure that the

circuit contacts are in good condition, prevent the poor contact of circuit from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol

or solvents. There are no serviceable parts inside the device. Please refer to the instructions under

“Installation instructions”.

Indice

Altri manuali FOS Technologies Attrezzatura per DJ

FOS Technologies

FOS Technologies FOS Ultra Par Manuale utente

FOS Technologies

FOS Technologies Pixel Blade Ultra Manuale utente

FOS Technologies

FOS Technologies TOURING PAR IP HEX Manuale utente

FOS Technologies

FOS Technologies Wash 360 LED Manuale utente

FOS Technologies

FOS Technologies Wash LED Quad III Manuale utente

FOS Technologies

FOS Technologies FOS ACL Line 12 Manuale utente

FOS Technologies

FOS Technologies FOS 12R Hybrid Manuale utente

FOS Technologies

FOS Technologies FOS HYDRO BSW Manuale utente

FOS Technologies

FOS Technologies Luminus Manuale utente

FOS Technologies

FOS Technologies 150W LED Spot Manuale utente

FOS Technologies

FOS Technologies FOS Spot 150W Manuale utente

FOS Technologies

FOS Technologies PAR 18x12W PRO Manuale utente

FOS Technologies

FOS Technologies PAR COB 200W LED TW Manuale utente

FOS Technologies

FOS Technologies SuperStorm L006796 Manuale utente

FOS Technologies

FOS Technologies FOS 20W RGB Manuale utente

FOS Technologies

FOS Technologies FOS 12R Hybrid Manuale utente

FOS Technologies

FOS Technologies FOS PAR 7x15 6 in 1 Manuale utente

FOS Technologies

FOS Technologies FOS Wash LED Quad II Manuale utente

FOS Technologies

FOS Technologies FOS BEAM IP Manuale utente

FOS Technologies

FOS Technologies 12R Hybrid PRO Manuale utente

FOS Technologies

FOS Technologies L004503 Manuale utente

FOS Technologies

FOS Technologies FOS Spot 40W Manuale utente

FOS Technologies

FOS Technologies A10-FB4 Manuale utente

FOS Technologies

FOS Technologies ZOOM 2825 Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente