Foscam FN8108H Manuale utente
2
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
3
Before You Start
Package Contents
NVR
Ethernet Cable
DC Power Adapter
USB Mouse
Quick Setup Guide
Screw Pack
Warranty Card
Data Hire and Power Wire of the Hard
Drives
Security Warning
•Foscam cameras and NVRs require good security practices to safeguard your
privacy. You should regularly change your camera or NVR password which is the
combination of numbers, letters and symbols
•You should update your camera or NVR regularly. Make sure your camera or NVR
has the latest firmware installed for your specific model and better experience.
Hard Disk Installation
WARNING
•Before installing a hard disk drive (HDD), please make sure the power is
disconnected from the NVR.
•It is recommended that a hard drive be used in 7200 high-speed or above.
1. Remove the cover from the NVR by unfastening the screws on the rear and bottom.
4
2. Connect one end of the data cable and power cable to the motherboard of NVR and
the other end to the HDD.
3. Place the HDD on the bottom of the device and then fasten the screws on the bottom
to fix the HDD.
Data
HDD
Power Cable
5
4. Re-install the cover of the NVR and fasten screws.
Device Connection
Monitor
Mouse
VGA Cable
USB HDD
NVR Power
Adapter (DC 12V)
Ethernet
Cable
HD OUT Cable
Ethernet Cable
Ethernet
Cable
Camera Power
Adapter (DC 12V)
6
Procedure
1. The NVR needs to connect to the router rst, and assign an IP address to the IP
Camera. If the NVR is not connected to the router, it may appear that the NVR cannot nd
the IP Camera.
2. Connect your display to one of the video outputs (VGA or HD-OUT interface).
3. Connect an external storage device to the USB interface of the NVR as a backup.
4. Connect a mouse to the USB interface.
5. Some devices need to connect to your router using an Ethernet cable, including the
NVR, PC and IP Camera. 6. Connect the power adapter to the power input port.
Log In
1. Turn on the power switch on the rear panel. After the NVR starts up successfully, the
power LED and HDD LED indicators will turn green. The startup page is displayed on the
screen.
2. Change password . For your security, please set a new password for your NVR before
Log In.
7
3. Login page.
Enter the Username and Password, then click on the OK button.
4. After modifying the password, you will be taken to the Setup Wizard.
Setup Wizard
The Setup Wizard can walk you through some important settings on the NVR.
1. Setting the time.
2. Format HDD. Click the Format button to set up the HDD. Note that this will delete all
files on the HDD. HDD Full Setting. Select Stop Record and Overwrite.
8
3. P2P. If you want to know the UID of the device, please scan the QR code. If you don’t
want to use the Setup Wizard next time, uncheck the Setup Wizard checkbox. Click the
Finish button to complete the setup wizard.
Uncheck the checkbox
9
or Right-click→Main Menu →Configuration →uncheck the Setup Wizard checkbox.
Click the Finish button to complete the setup wizard.
Add IP Camera
You can add an IP Camera that is connected to the internet on the NVR.
1. Right-click on main interface, select Channel Config.
2. Select your IP Camera or Auto added IPC
3. Click Add.
4. Enter username and password of the camera. If your camera is in the factory default
state, you do not need to enter the user name and password.
5. Click OK.
Select a protocol depending on which IP Camera you have.
•FOSCAM protocol: The High Denition (HD) IP Cameras for Foscam.
•ONVIF protocol: IP Cameras which support ONVIF protocol.
1. Select Your IP Camera
2. Click Add
10
Recording
After the IP Camera is added successfully to the NVR, enable Scheduled Record
functionality to the following methods when in the Live View mode.
Scheduled Record
Right-click →Main Menu →Record →choose recording channel →Save (Actually, the
NVR system have default set 24h scheduled recording).
In the Live View mode, the icon is at the bottom right of the screen for each
channel, indicating recording is on going.
Event Record
If you want to start event recording, select Event in Type, use the left mouse button to
select the time (turned to green), if the other channels operate in the same way, select
Copy.
Indice
Lingue:
Altri manuali Foscam Hardware di rete
Foscam
Foscam FN3004H Manuale utente
Foscam
Foscam FN9108HE Manuale utente
Foscam
Foscam FN3104W-B4 Manuale utente
Foscam
Foscam FN3104H Manuale utente
Foscam
Foscam FN3104W Manuale utente
Foscam
Foscam FN3004H Manuale utente
Foscam
Foscam FN7108HE Manuale utente
Foscam
Foscam FN3004H Manuale utente
Foscam
Foscam FN3108E Manuale utente
Foscam
Foscam FN3109H Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
