Fostex FD-8 Manuale utente
FD-8 Owner’s Manual Supplement
<NOTE>: When formatting a large capacity hard disk, the time required to format will be in
relation to disk size. As a general estimate, it requires about 15 minutes to format 1GB and
thus, as an example, it will take about 7 hours for a 30GB hard disk.
The functions explained here have been added to the FD-8 subsequent to version
1.10 because of a version up of the software. Prior to operating the FD-8, please
read this supplement together with the main manual.
1. Large capacity hard disks can now be used.
It is now possible to use a 2.5 inch E-IDE hard disk with a capacity up to about 30GB
(FS=44.1kHz) for the FD-8 internal current drive disk.
2. In the BAR/BEAT/CLK (bar/beat/clock) time base, the offset figure of the BAR
that indicates the head of the disk can now be edited.
Although [Time Base] is explained in [Before Operating] in the main owners manual, for
the unit representing the present traveling position of the FD-8, MTC (MIDI time code) or
BAR/BEAT/CLK are employed in addition to ABS (absolute time). For this reason, the
figure indicating the present disk position will be different depending on the selected
time base.
With the FD-8 in the initial setup state, when the disk is at the head position (ABS 00M
00S 00F) the MTC offset indication will be [MTC 00H 59M 57S 00F], and when by BAR/
BEAT/CLK it will be [-002BAR 1BEAT 00CLK].
Before this version up, changing the offset figure was limited to MTC and the BAR/BEAT/
CLK offset figure was fixed to [-002BAR 1BEAT 00CLK]. But after this version up, the BAR
offset figure of BAR/BEAT/CLK can now be changed and set to any figure within a range
of -002 ~ -009.
The FD-8’s initial state [-002BAR 1BEAT 00CLK] will always be displayed and the BAR
offset figure will be [-002BAR].
In order to set the offset figure of the BAR/BEAT/CLK display, use the SETUP mode of the
FD-8 in the same manner for setup of MTC offset. For procedures, refer to the reverse
side explanation. For setup of MTC offset, please refer to [SETUP mode] of the main
owners manual.
1. Preselect the program to which offset is to be setup.
The following example shows in the display that
program 2 have been selected.
2. Switch to the SETUP mode by pressing the SETUP
key.
In the initial setup, the [Sign. Set?] menu will be
displayed (If a different menu is displayed, rotate the
JOG dial to display the [Sign. Set?] menu.).
3. Then press the EXECUTE/YES key.
The display will change to [Sign. Chk] and the
presently set beat will be shown. In the initial setup,
the display will show that the first bar is set to 4/4
beat.
4. Rotate the JOG dial counter-clockwise.
The offset figure of the presently set bar is displayed
and in the initial setup, [-002BAR OFFSET] will be
displayed as shown below.
5. Press the EXECUTE/YES key.
Simultaneous with entering [Sign. Edit] mode, [2] of
-002BAR will blink and the BAR offset figure can then
be editied.
6. Enter the desired offset figure by rotating the JOG
dial, and then press the EXECUTE/YES key.
Any offset figure in the range of 2~9 can be input
(Example below show that [5] had been entered for
the BAR figure.). When the EXECUTE/YES key is
pressed after input of the above number, the offset
figure thus input will be setup and the display will
change to the [Sign. Set?] menu.
7. Exit from the SETUP mode by pressing the EXIT/NO
key.
Setup procedures for BAR/BEAT/CLK offset
<NOTE>: Offset setups can be executed for each program. The setup content will be
maintained even though power is switched off.
FOSTEX CORPORATION
3-2-35, Musashino, Akishima-shi,Tokyo 196-0021, Japan
FOSTEX CORPORATION OF AMERICA
15431, Blackburn Ave., Norwalk, CA 90650, U.S.A.
Blink
Blink
Blink
C
PRINTED IN JAPAN AUG.1999 8288 677 000 FX.
CLK
SYNC OUT DRIVESCSI
AUTO A.PUNCH
SETUP
BAR
44.1kHz
EXECUTE
/YES
EXECUTE
/YES
CLK
SYNC OUT DRIVESCSI
AUTO A.PUNCH
SETUP
BAR
44.1kHz
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK SCSI
BAR
44.1kHz
CLK
SYNC OUT DRIVESCSI
AUTO A.PUNCH
SETUP
BAR
44.1kHz
EXECUTE
/YES
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK SCSI
BAR
44.1kHz
CLK
SYNC OUT DRIVESCSI
AUTO A.PUNCH
SMF
PGM
ABS
44.1kHz
CLK
SYNC OUT DRIVESCSI
AUTO A.PUNCH
SMF
PGM
ABS
44.1kHz
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK SCSI
44.1kHz
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK SCSI
44.1kHz
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK SCSI
44.1kHz
SETUP
Altri manuali per FD-8
4
Indice
Altri manuali Fostex Apparecchiature di registrazione
Fostex
Fostex 280 Manuale utente
Fostex
Fostex D2424LV MKII Manuale utente
Fostex
Fostex FD-4 Manuale utente
Fostex
Fostex CR200 Manuale utente
Fostex
Fostex 8335 Manuale utente
Fostex
Fostex FD-8 Guida utente
Fostex
Fostex D2424LVmk2 Manuale utente
Fostex
Fostex FR-2 Manuale tecnico
Fostex
Fostex MR-8HD Manuale utente
Fostex
Fostex 450 Manuale utente
Fostex
Fostex E-16 Manuale utente
Fostex
Fostex E-2 Manuale utente
Fostex
Fostex 280 Manuale utente
Fostex
Fostex PD606 Manuale utente
Fostex
Fostex 4011 Manuale utente
Fostex
Fostex CR300 Manuale utente
Fostex
Fostex 8700 Manuale utente
Fostex
Fostex M80 Manuale utente
Fostex
Fostex UR-2 Istruzioni e ricette
Fostex
Fostex APPENDIX Manuale utente
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
