Foxconn T99B226 Manuale utente

0/27

All product specifications are subject to change without notice

CBSD Outdoor Small Cell

T99B226

User Manual

1/27

All product specifications are subject to change without notice

1. Introduction ................................................................................................2

2. HW installation guide and specifications.........................................................3

3. Private Network Solution ............................................................................12

3.1 Configuration Overview..............................................................................12

3.1.1 Basic Setting...............................................................................................13

3.1.2 Advanced Setting........................................................................................14

3.1.2.1 Cell Configuration.....................................................................................14

3.1.2.2 Rem Configuration....................................................................................15

3.1.2.3 Gateway Configuration .............................................................................16

3.2 Sniffer........................................................................................................16

3.3 Syslog ........................................................................................................16

3.4 Alarm........................................................................................................17

3.5 Diagnostic ..................................................................................................17

4. Warranty and compliance...........................................................................18

5. Frequently Asked Questions........................................................................19

6. Troubleshooting..........................................................................................25

2/27

All product specifications are subject to change without notice

1. Introduction

A compact, high output power, resilient CBRS (Citizens Broadband Radio

Service)compliedLTESmallCellispresentedinFig1.1.Thedeviceiswateranddust-

proof (IP65) and can be pole mounted, which makes it suitable to be deployed in a

dense factory area, both indoors and outdoors.

Figure 1.1 T99B226 overview

The LTE CAtechnology deployed in this outdoor small cell is complied with specification

defined by IEEE 3GPPAlliance. The small cell has four LTE and one GPS antenna ports and is

powered through 56 VDC PoE. Its LTE interface operates in CBRS band and supports SAS,

Spectrum Access System. By using GPS Timing synchronization, handover between various

small cells can be achieved. Thisis essential for scenarios that need quick switches between base

stations, such asAGV (Automatic Guide Vehicle) for factory automation.

3/27

All product specifications are subject to change without notice

2. HW installation guide and specifications

This section describes HW overview of the Outdoor Small Cell-T99B226

Connectors and Interfaces

As shown below in fig 2.1,T99B226 consistsoffourN-typecableconnectors (LTEantenna

#1,2,3,4) on the bottom side of the device for LTE antennas and an ethernet RJ45 port for power.

There are four bolt holes on the back side of the device so that it can be pole mounted onto a

factorypole byusing a mounting bracket. The SMAconnector on the back sideof the device can

be used to connect to GPS antenna and provide 3.3V DC power to it.

Figure 2.1 T99B226 Ports and Connectors

LTE Antenna #1 (Ant2-Main)

LTE Antenna #2 (Ant2-Div)

RJ45

GPS Antenna

LTE Antenna #3 (Ant1-Main)

LTE Antenna #4 (Ant1-Div)

Vent valve

Bracket screw

4/27

All product specifications are subject to change without notice

Cable routing and installation guide

Whileinstalling, thedeviceshouldhaveaclearview towardspotentialusertransmitters and

not obstructed by nearby trees or buildings. Once you pick an ideal installation spot, place the

mast bracket and wrap it around the mast, clamp the bracket and device together by tightening

screws through bolt holes on the back of device and the bracket.

LTE antenna wires need to be pulled from the N-Type connectors on device along four

bracket arms to four antennas on each corner as shown in figure2.2 and the running wires can

be fixed onto bracket arms using bracket ties. It is the best practice to keep antenna rods

perpendicular to bracket branches and make sure four antennas are evenly distributed in four

corners.

Figure 2.2 T99B226 cables top view

LTE Antenna #3

LTE Antenna #4

Cable routing on Bracket

LTE Antenna #1

LTE Antenna #2

5/27

All product specifications are subject to change without notice

Moreover, the GPS antenna needs to be positioned at a place where GPS reception is solid,

and the wire connecting GPS antenna to the device needs to be attached to the pole to ensure the

stability of the connection during non-ideal weather conditions. Power for T99B226 is

provided by connecting the power to a POE (power on Ethernet) adapter and through the

waterproof ethernet cable to the ethernet port next to the antenna ports as shown in fig2.3. For

the same reasons, the wires need to be attached to the pole firmly and the waterproof ethernet

port is complied with IP65 regulations which makes it resilient to outdoors conditions.

Figure 2.3 T99B226 assemble front view

Installation bracket guide.

Total overview:

Cable tie

LTE Antenna

GPS Antenna

5VDC output

for supporting

5V A ct i v e

GPS Antenna

LTE Antenna

PoE adaptor

6/27

All product specifications are subject to change without notice

Assembly Step1: Bracket base and housing assemble:

7/27

All product specifications are subject to change without notice

Assembly Step3:Antenna holder assemble:

Assembly Step4:Antenna holder and bracket assemble:

8/27

All product specifications are subject to change without notice

Assembly Step5: Fix the bracket on pole:

Assembly Step6:Assemble Device on bracket:

9/27

All product specifications are subject to change without notice

Assembly Step7:AssembleAntenna on antenna holder:

Altri manuali per T99B226

Indice

Altri manuali Foxconn Modulo wireless

Foxconn

Foxconn J20H084ac Manuale utente

Foxconn

Foxconn WBUR56 Manuale utente

Foxconn

Foxconn RPQN O-RU Guida all'installazione

Foxconn

Foxconn 5G + 4G AIO Small Cell Manuale utente

Foxconn

Foxconn J20H081 Manuale utente

Foxconn

Foxconn J20H076 Manuale utente

Foxconn

Foxconn WBU063-VZ Manuale utente

Foxconn

Foxconn T99B226 Manuale utente

Foxconn

Foxconn J20H086 Manuale utente

Foxconn

Foxconn J20H090 Manuale utente

Manuali Modulo wireless popolari di altre marche

Laird

Laird RM024 Manuale utente

Laird

Laird BT830-SA Guida rapida alla configurazione

Ebyte

Ebyte E49-400T20S Manuale utente

Fibocom

Fibocom FM101-NA-20 Istruzioni per l'installazione

Waldmann

Waldmann EnOcean TALK MODUL G2 Manuale utente

Smartech

Smartech LBT-1.DO4 Manuale utente

Cooper Wiring Devices

Cooper Wiring Devices ESPIRE RF RFAPM Manuale utente

Yuga

Yuga CLM920 Manuale utente

Waldmann

Waldmann TALK Bluetooth Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions UC864-G Manuale di installazione

Ebyte

Ebyte E07-900M10S Manuale utente

Quectel

Quectel SC690A Series Supplemento

Panasonic

Panasonic INDUSTRY PAN9028 Guida rapida alla configurazione

Ebyte

Ebyte E70-433NW30S Manuale utente

LongSung Technology

LongSung Technology U9507E Manuale utente

Wistron NeWeb

Wistron NeWeb DNUR-S2 Manuale utente

Ebyte

Ebyte E49-400M20S4 Manuale utente

RF-Star

RF-Star SimpleLink RF-BM-2652P1 CC2652P Manuale utente