Foxtech Seeker-10 360TR Manuale utente
User manual
S eeker-10 360TR
High Precision Gimbal
-1-
Content
4、Packing List…………………………………………………………………………4
7、Mechanical&electronic characteristics………………………5
1、Introduction…………………………………………………………………………2
6、Installation………………………………………………………………………5
8、Performance………………………………………………………………………5
9、Tracking Gimbal Signal Wiring Diagram…………………………6
3、Gimbal Diagram……………………………………………………………3
5、Dimensional Drawing………………………………………………………4
2、Target Tracking…………………………………………………………………2
11、
GPS information overlay&serial port control diagram………………12
GPS information overlay&serial port control diagram
10X Zoom Camera Introduction
10、10X Zoom Camera…………………………………………………………10
Target Tracking Function
Gimbal Camera Introduction
FOXTECH Seeker-10 360TR is a 3-axis gimbal camera featuring 10X
optical zoom, 360 degrees infinite rotation and object tracking.It
supports Ethernet output, the video output resolution is 1080p/30fps,the
effective pixels is 2.12MP.
SEEKER-10 360TR 3-axis gimbal developed based on FOC technology,
features excellent stability, accuracy and sensitivity.It has fast speed and
low speed modes. Fast speed mode is used for small zooming range;Low
speed mode is used for large zooming range.
SEEKER-10 360TR supports PWM, S.BUS and serial command control.
-2-
6）Tracking Velocity: ±32 pix/frame
8）Target memory time: 100 sessions
7）The root mean square value of noise at the target position
＜0.5 pixel
1、The built-in normalized cross-correlation tracking algorithm, combined with
the target lost recapture algorithm, realizes the stable tracking of the target;
Support user to display custom characters, adaptive gate, cross
wire and tracking information display.
2、Tracking Performance
2）output lag＜15ms
5）Target Size: 32x32 to128*128 pixels
3）min. target contrast 5%
1）Data refresh rate: 50Hz
4）Signal-to-noise ratio 4
Gimbal Diagram
-3-
!
Please ensure that the motor is not blocked by anything during rotation. If the gimbal
is blocked during rotation, please clear the obstruction immediately.
[1]Yaw axis motor
[2]Roll axis motor [4]HD Zoom Camera
[3]Pitch axis motor
[
1
]
[
4
][
3
]
[
2
]
pack of screw*1
M3*5mm*12
copper pillar*4Damper*12
Dimensional Drawing
Packing List
gimbal camera*1
Voltage
IDDT
Size
12V
450mA@12V
L91.2*W126.9*H99.5mm
IDDQ
temperature
Weight
330mA@12v
-20~+80
620g
Performance
Mechanical&electronic characteristics
Installation
Pitch：-90°~+90°; Roll: -45°~+45°
Yaw：n*360°
Control precision:Pitch & Roll: ±0.02°Yaw: ±0.03°
-5-
-6-
Tracking Gimbal Signal Wiring Diagram
SD card: max 128G ,class10
FAT32 or exFAT format
SD card: 最大支持128G 卡，class10 高速
卡
格式化为FAT32 or exFAT 格式
USB
123
S.bus/Rx
Roll/Tx
Pitch
Yaw
Mode
Zoom
Focus
Pic/Rec
Multi
Av
PWM in
5V output
GND
TTL 15200/8/1/N
USER BOARD
RX
TX
GND
-7-
Pitch:PWM in, pitch control ( 俯仰控制，PWM 输入）
S . b u s / R x :c o n n e c t t o R x 2 f o r t r a c k f u n c t i o n . ( S . b u s / R x
RX2
Roll/ Tx:connect to Tx2 for track function. ( Roll/ Tx 用户不可用，默认出厂
与TX2连接，用做跟踪功能）
1 pitch up 俯仰向上
2 pitch stop 俯仰停止
3 pitch down 俯仰向下
We have protocol for
co ntr ol th e gim ba l
and camera, please
contact our technical
su p p or t f o r de t a i l
doc.
USER BOARD /
GPS module
TX
GND
RX
TTL 115200/8/1/N
Yaw:PWM in, Yaw control(指向控制，PWM 输入）
1 Yaw right 指向右转
2 Yaw stop 指向停止
3 Yaw left 指向左转
1 zoom tele 放大
2 stop zoom 停止
3 zoom wide 缩小
Mode:change the speed / home position (调整云台控制速度/一键回中）
1 无
2 无
3 无
ZOOM: zoom the camera (放大，
缩小）
focus : focus the camera ( 手动
调焦，默认自动对焦模式）
-8-
1
2
3
高位 低位
Position 3: Low speed mode,control Yaw and Pitch in this mode and
then the gimbal will
move at the lowest speed;
Turn the knob to any position above position 3: change speed; at this
time control Yaw and Pitch, gimbal control speed will be increased
(The speed will change depending on the position of the switch)
Turn the knob to position 2-1-2: gimbal returns to the middle position.
Switch from 2 to 1 and back to 2 continuously and quickly, gimbal back
to home;
Switch from 2-1-2-1-2 continuously and quickly,start follow mode;
Switch from 2-1-2-1-2-1-2,start head-locking mode.
Pic/Rec picture / start record stop record （ ）:， 拍照，开始录像，停止录像
1
2
3
Switch 2 to 1:
start record / stop record.(从2 切到 1 ,开始录像，再 切一 次， 停
止录像）
start record, the OSD display rec hh:mm:ss ; (录像开始后，会显
示录像时间）
Stop record, the OSD display STBY. (录像停止后，显示STBY)
Switch 2 to 3:
take a picture . (从2 切到 3,拍一张照片）
OSD display’REC IMG’a second. (拍照会显示 REC IMG
几秒钟）
Multi tracking control: (跟踪控制）
1
2
3
AV: NO AV output this model。 （本型号没有AV 输出）
-9-
C h a n g e t h e o b j e c t d u r i n g t r a c k i n g ( 二 次 跟 踪 :
跟踪过程中，微调跟踪的目标）
Switch 1 to 2: display the cross cursor. Adjust the object to
the cross cursor. (调出十字标，调整目标到十字）
Switch 3 to 2: display the cross cursor，use Pitch/Yaw to
a d j u s t t h e c r o s s c u r s o r .
(调出十字标，用俯仰，航向通道调整十字标到新的目标位置）
Position 1: exit the tracking (退出跟踪模式）
Switch 2 to 3: start tracking. (开始跟踪， 右下角显示偏移量）
Switch 2 to 3: start tracking. (开始跟踪，右下角显示偏移量）
Indice
Altri manuali Foxtech Macchina fotografica digitale
Foxtech
Foxtech EH26 Manuale utente
Foxtech
Foxtech FH230 TR Manuale utente
Foxtech
Foxtech Seeker-40 Manuale utente
Foxtech
Foxtech SYK-30 Manuale utente
Foxtech
Foxtech 3DM V3 Manuale utente
Foxtech
Foxtech SEEKER-640 Manuale utente
Foxtech
Foxtech Map-02 Manuale utente
Foxtech
Foxtech Map-A7R Manuale utente
Foxtech
Foxtech Map-A7R Manuale utente
Foxtech
Foxtech SYK-20 Manuale utente
Foxtech
Foxtech EH10 10X Manuale utente
Foxtech
Foxtech FH314 Manuale utente
Foxtech
Foxtech EH30-MTIR Manuale utente
Foxtech
Foxtech SYK-10 Manuale utente
Foxtech
Foxtech SYK-20L Laser Night Vision 4K Manuale utente
Foxtech
Foxtech SYK-10L AI Manuale utente
Foxtech
Foxtech 809111 Manuale utente
Foxtech
Foxtech SYK-10L 4K Manuale utente
Foxtech
Foxtech SurePulse VS Manuale utente
Foxtech
Foxtech Map-A7R Manuale utente
