Fraser XIFOS 33 Manuale utente

XIFOS33

OPERATING

INSTRUCTIONS

WITH INTEGRATED REMOTE MONITOR

XIFOS33OI-Iss.3-EN

Contents Page

1 Introduction .............................................4

2 Safety ....................................................6

3 PositioningoftheBar....................................7

4 Installation..............................................10

5 ElectricalConnections..................................11

6 StatusLEDs .............................................14

7 OperationandControl..................................15

8 Commissioning .........................................18

9 Maintenance............................................18

10 Troubleshooting ........................................19

11 RemoteInterfaceandWiringExamples ...............20

12 SpecificationandDimensions ..........................24

13 CertificationandCEDeclarationofConformity .......25

14 SparePartsandAccessories ............................26

Fraserstaticcontrolequipmenthasbeendesignedtogive

youmanyyearsofproductiveservice.However,thescience

ofstaticcontrolhasuniquerules,whichmustbefollowedto

allowtheequipmenttogiveagoodreturnonyourinvestment.

Pleasereadthefollowingoperatingandmaintenance

instructionscarefully.

Contents

4© Fraser Anti-Static Techniques Ltd 2020

TheXIFOS33barisoneoftherangeofhighperformanceDCstaticeliminators

fromFraserAnti-StaticTechniques.Theseproductsareusedbyleading

manufacturersthroughouttheworldtoincreasesafetyandproductivity.

Itisessentialthatyoureadandunderstandthecompletemanualbeforeinstalling

andusingthisequipment.Thisisimportantforsafetyandforwarrantycover.

Features and Benefits

TheFraserXIFOS33isahigh-performancebardesignedforlong-range

neutralisationofelectrostaticallychargedsurfaces.

Poweredby24VDC,itfeaturesintegratedhighvoltagesuppliesmeaningthatno

highvoltagecablingisrequired.

1. Introduction

Mountingontothemachineiswith‘T’xings

thatslideintotheslotinthebar.

DistanceControl:distance-to-targetsetting.

See Section 7.

Thestatusofthebar,includingtheneedfor

cleaning,isindicatedby5bi-colourLEDs

ontheendcapofthebar.Duplicateoutputs

enableintegrationwithacontrolsystemor

PLC.SeeSection6.

IntelligenceControl:IntelligenceON/OFF.

See Section 7.

The24VDCpowersupplyandremote

monitoringconnectionsaremadeviaan

M125-pinconnector.

AnexternalAC-DCPSUcanbeorderedif

24VDCisnotavailable.

XIFOS33OI-Iss.3-EN

1.1 Explanation of Symbols

Warning!

Thissymbolappearingintheoperatinginstructionsreferstooperationswhich,

ifcarriedoutimproperly,canresultinseriouspersonalinjuries.

Caution!

Thissymbolappearingintheoperatinginstructionsreferstooperationswhich,

ifcarriedoutimproperly,canresultindamagetoproperty.

Information!

Thissymbolreferstoinformationthatrelatestoobtainingthebestperformance

andoperatinglifefromtheproduct.

1.2 Checking on Delivered Equipment

Theequipmentleavesourfactoryinsuitableprotectivepackaging.Pleasecheck

thatitisundamagedwhenitarrives.Ifthereisvisibledamage,contacttheFactory

oroneofourDistributorsbeforecarryingoutanyinstallation.

Checkthatthepartswhichhavebeendeliveredarethesameasyouhaveordered.

LooseParts Barsupto1,000mminlengtharesuppliedwithtwo‘T’xings.

  Extra‘T’xingsaresuppliedforeachadditional500mmorpart

  thereof.Forexample:

   750mm: 2‘T’xings

   1,500mm: 3‘T’xings

   1,750mm: 4‘T’xings

  Itisimportanttouseallofthesupplied‘T’xings.

  EmitterKeyandtwospareemitters.

  PowerSupplyCable.M125-pinConnectorandleadorPower

  SupplyUnit-asperorder.SeeSection14fordetailsofcablesand

  otheraccessories.

Warning!

DO NOT USEstandard‘computerstyle’PSUs.Thesedonothavesecondaryearth

connectionsandriskshockstotheoperatoranddamagetothebar.Onlyusethe

FraserexternalPowerSupplyUnit(PartNo.NEOS-PSU).

1. Introduction

6© Fraser Anti-Static Techniques Ltd 2020

TheXIFOS33barhasbeendesignedinaccordancewiththesafetyrequirements

ofEN62368-1:2014.ThisIEC-derivedstandardisharmonisedundertheEULow

VoltageDirectiveandrecognisedbyUL.

• Theemitterpinsareresistivelycoupledtothehighvoltagesupplies.Theemitters

areaClass1electricalenergysource,asdefinedinEN62368-1:2014.Contact

withtheemittersisnotpainfulandwillnotresultinelectrically-causedinjury,but

maycauseadetectablesensationduetothesmallcurrentwhichwillflow.

• AswithallpulsedDCstaticeliminators,itispossiblefortheusertoreceivea

smallstaticshockasaresultoftheirbodybeingchargedbythebar,andthen

dischargingtoanearbyearthedobject.Thisisnotdangerous,butmaybe

uncomfortableandcausesurprise.

• Theemitterpinsofthebararenecessarilysharp.TheemitterpinsareaClass2

mechanicalenergysource,asdefinedinEN62368-1:2014.Contactwith

themmaybepainful,butwillnotcauseaninjuryrequiringemergencymedical

attention.Takecarewhenhandlingthebar.

• Installationandmaintenanceworkonthebarmustonlybecarriedoutby

suitablyqualifiedpersonnel.

• Thenegativepoleofthe24VDCsupplyprovidedtothebarmustbe

permanentlyearthed.

• Adequateinstallationearth/groundisrequiredtoensuresafeandproper

operation.

• DonotconnectordisconnecttheM12cablefromthebarwhileitispowered.

• Asmallamountofozonewillbeproducedaspartoftheionisationprocess.

Wheninstalledcorrectlythelevelofconcentrationofozoneislessthan0.1ppm

andiswithininternationallyacceptedlimits.

• Anychangestotheequipmentwithoutwrittenconsentofthemanufacturerwill

nullifythewarrantyandcertifications.

• Thebarisintendedforuseinindoorfactoryenvironmentsonly.

Itisnotsuitableforoutdooruse.

2. Safety

XIFOS33OI-Iss.3-EN

3. Positioning of the Bar

Thebestlocationisat,orimmediatelybefore,theareawherestaticiscausingthe

problem.Rememberthatstaticcanberegeneratedifthematerialpassesover

rollersorthroughaprocessafterneutralising.AStaticMetersuchastheFraser715

isusefultodeterminethebestposition.

Important: Except on a winding reel of material (seetheexamplesonthefollowing

page),thematerialtobeneutralisedmustbeinfreeair,nottouchinganother

surfaceasitpassesthebar.Itisnotpossibletoneutralisestaticelectricitywhere

thematerialistouchinganothersurfaceorroller.

MATERIAL

Incorrect location

Staticneutralisationwillbe

verypoorifthereisnotfree

airoppositethebar.

FREE AIR

MATERIAL

Good location

Freeairopposite

thebarallowsgood

neutralisation.

8© Fraser Anti-Static Techniques Ltd 2020

Generally,witharewindorunwind,itisdesirabletousealong-rangebartocope

withthechanginggeometrysothatyoucanneutralisethereelfromthecoretothe

nisheddiameterattheendofthewind.

Thereisanoptimumlocationtoneutralisethereel,whichisshownbythefollowing

diagrams.

TheprincipleistoneutralisethelmAFTERitleavesthenalrollerandasitjoins

thereel.

Ifthereisalay-onorcontactroller(C),thebestpositionfortheXIFOS33isonthe

sidewherethelmleavesthelay-onroller-inthiscasetheunderside(A)-because

itcanneutralisethechargeassoonasitiscreated.Ifthisisnotpractical,then

positionthebaronthetopside.(B)

Lay-on or Contact Roller Example

3. Positioning of the Bar

XIFOS33OI-Iss.3-EN

OnacentrewindertheXIFOS33maybepositionedaboveorbelowthereel.Itisa

goodideafortheionisationtobedirectedmainlyatthereel,butalsocatchingthe

singlesheet,asshownat(A).Position(B)isalsoacceptable.

Itisoftennotpossibletoplaceabarintheoptimumposition(A).Thereasonforthis

maybethattheidealbarlocationwouldgetinthewayoftheloading/unloading

processforthereelsorwouldbeinapositionwhereoperatorsmightstandonit.

Inadirtyordustyenvironment,itisbettertoplacethebarfacingdown,sincethe

faceofthebarwillnotbecoveredbythedust.Thisisnotaproblem.Itispossibleto

positionthebaratotherpositions,suchas(B)andstillachieveaverygoodresult.

Wealwayssaythatalmwebmustbein‘freeair’andnottouchingarollerto

achievegoodneutralisation.Thisisbecauseweknowthatthechargeonthe

materialwilltemporarilycombinewiththerollerandnotbeavailableforremoval

bytheeliminator.Thisremainstrue.However,onceyouhaveanumberoflayers

onareelorwinder,allwiththesamepolarityofchargeonthem,thechargecanno

longercombineandcanthereforebeneutralisedlayerbylayer.

Centre Winder Example

3. Positioning of the Bar

10 © Fraser Anti-Static Techniques Ltd 2020

4. Installation

• Useallofthe‘T’fixingsprovidedformountingthebar.The‘T’fixingsslideinto

theslotinthebaseofthebar.Whenmountingthebar,the‘T’fixingsmustbe

evenlydistributedalongthelengthofthebar.Donotallowmorethan800mmof

unsupportedbarbetween‘T’fixings.

• Thebarmustbedryandoil-free.

• Onlymountthebarwiththeslottouchingthemachineorthemountingbracket.

• Whenmountingtothemachineoronabracket,makesurenometalextends

beyondtheslotinthebar.Seethediagrambelow.

Note:Longbarsneedcarefulhandlingduringinstallationtoavoiddamage.

Barslongerthan2,000mmmustbehandledbytwopeople.

Areatobefreeofall

groundreferences

R=min.300mm

• Itisimportantthattheemitterpinsarenottouching,orclosetometalobjects,

toavoidsparkerosionthatwilldamageboththebarandthemetalobject.

• Thedistancefromthematerialshouldbe:250-1,500+mm.

Correct mounting

bracket position

Incorrect mounting

bracket position

Indice

Altri manuali Fraser Alimentazione elettrica

Fraser

Fraser IONFIX COMPACT Manuale utente

Fraser

Fraser HP50-ION Manuale utente

Fraser

Fraser IONFIX COMPACT Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente