Freescale Semiconductor MPC8349EA MDS Manuale utente

HW Getting Started Guide

MPC8349EA MDS

Processor Board

Nov 2006: Rev. A

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Freescale Semiconductor Page 1 of 8

Contents

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Required Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Definitions, AcroRev. And Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Step 1: Check HW kit contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2: Connect plastic spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 3: Check Switches and Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 4: Assemble and connect the power supply kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 5: Perform initial board power up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 6: Connect the JTAG connectivity unit to the board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 7: Attach remaining cables to the board according to your development needs. . . . . . . . . . . . . . . . . . . . . . 7

About This Document

This document shows how to connect the MPC8349EA MDS processor board and verify its basic operation, in a step by step

format. Settings for switches and jumpers are shown, as well as instructions for connecting peripheral devices. In addition,

instructions for connecting the MPC8349EA MDS processor board to an Integrated Development Environment (IDE), such as

Freescale’s CodeWarrior®are included, but instructions for working with the IDE are beyond the scope of this document. This

version of the board has a faster DDR2 (400MHz), and a flash memory of 32MB.

Required Reading

It is assumed that the reader is familiar with the MPC8349EA chip, and the contents of the MPC8349EA Reference Manual.

Definitions, AcroRev. And Abbreviations

BCSR board control and status register LED light emitting diode

BMS boot memory space PCI peripheral component interconnect

CFG_RS bit in RCW register PCI_SYNC_OUT chip pin

CLKDIV clock division PIB platform I/O board

CLKIN clock input PLL phase lock loop

COP debug port in PowerPC RCW reset configuration words

DDR double data rate DRAM ROM read-only memory

DIP dual in-line package SHMOO sweep test (of frequency and core voltage)

I2C Philips serial port TLE bit in RCW register

JTAG IEEE standard 1149.1 TSEC triple speed ethernet controller

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Page 2 of 8 Freescale Semiconductor

MPC8349EA MDS Processor Board

HW Getting Started Guide

Step 1: Check HW kit

contents

1. MPC8349EA MDS Processor

Board

2. AC/DC 5V/5A universal power

supply kit

3. RS232 standard serial cable

with two 9-pin

connectors-extends the

Freescale adaptor cable

4. Freescale adaptor cable (joined)

with one RJ45 and two RS232

connectors:

a) RJ45 10-pin plug

b) RS232 9-pin D-type

connector

5. USB adaptor and connector:

a Mini USB adaptor: 5-pin

(male) and 4-pin (female)

b USB cable with two

connectors: standardA and

miniB.

6. Ethernet cables (2) with RJ45-8

connectors

Not shown:

7. Four sets of plastic spacers

(male/female)

8. One Allen wrench

9. CodeWarrior SW kit (includes

JTAG connectivity unit)

10. MPC8349EA MDS Processor

Board documentation

4a 4b

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Freescale Semiconductor Page 3 of 8

Step 2: Connect plastic spacers

Plastic Spacer

Plastic Screw

Four sets of plastic spacers screw

into holes located at (approximately)

the four corners of the board.The

spacers raise and stabilize the board.

1. From under the board, insert a

spacer into one of the board's four

spacer holes.

2. Attach a female spacer onto the

male spacer.

3. Repeat for the three remaining pairs

of spacers.

Step 3: Check Switches and

Jumpers SW5

SW2

SW7 SW4

SW6 SW3

Socket for MPC8349EA Switches SW3,4,6,7

JP1 SW5

The MPC8349EA MDS Processor

Board has two rows of Dual-In-Line

Package (DIP) switches.The default

DIP-switch positions set-up the

MPC8349EA MDS Processor Board

clock mode as shown in the table

below:

MPC8349EA MDS Processor

Board Clock Mode

e300 Core Frequency 533 MHz

CCB 266 MHz

DDR2

(can be changed to 400MHz)(

266 MHz

Local Bus 133 MHz

1 <- ->0

1: CFG_RS0 ON

2: CFG_RS1

3: CFG_RS2

4: CLKDIV

5: SPMF0

6: SPMF1

7: SPMF2

8: SPMF3

12 3 4 567 8

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Page 4 of 8 Freescale Semiconductor

Step 3.a: SW3 Configuration

Set 1

The "On" DIP Switch position

corresponds to a signal value of

“zero”.

SW3.1-SW3.3

CFG_RS sets the Reset Configuration Words Source

ON: value of zero

factory setting: '000' when RCW is fetched from the local bus

DIP-switch SW9/3 FCFG: chooses between BCSR or Flash RCW source

SW3.4

CLKDIV selects the relationship between CLKIN and PCI_SYNC_OUT

if the MPC8349 is configured as a PCI Agent (factory setting) then CLK_DIV

is low

SW3.5-SW3.8

SPMF selects System PLL Multiplication Factor

factory setting: '0100'

clock ratio: csb_clk/CLKIN = 4 (csb_clk = 266MHz) or csb_clk/PCI_CLK = 4

Factory default setting: 00000101

Step 3.b: SW4 Configuration

Set 2

SW4.1-SW4.2: TSEC1/TSEC2

Selects the protocol used by the two-port TSEC controller

factory setting: enters GMII mode when TSEC1 and TSEC2 initiate similar

2’b10

SW4.5: BMS: Selects boot memory space

factory setting is ‘1’ when boot memory resides in upper eight Mbytes at

0xFF80_0000 to 0xFFFF_FFFF

SW4.6 TLE: Selects endian mode

factory setting: '0'; big endian mode

SW4.7: PCI64: Selects PCI width

factory setting: '0'; 32-bit width

SW4.8: FCFG: Sets RCW source on local bus

‘0’: BCSR source; setting uses values from SW3 and SW6.

‘1’: Flash source - setting is burned in flash memory

Factory setting: ‘0’

Factory default setting: 10101000

Step 3.c: SW6 Configuration

Set 3

SW6.1-SW6.2: Boot sequencer configuration

Boot sequencer loads configuration data from the serial ROM.

Factory setting: ‘00’; disables access to I2C ROM.

SW6.3-SW6.5: Boot ROM location

Factory setting: ‘110’; provides flash boot on local bus

SW6.6 DDR: Clock mode

Factory setting: ‘0’; operates with DDR clock (identical to csb_clk)

SW6.7: Local bus clock mode

Factory setting: ‘1’; operates with local bus clock - half of csb_clk

SW6.8: Software watchdog

Factory setting: ‘0’; with software watchdog disabled

Factory default setting: 00110010

1 <- ->0

1: TSEC1-0 ON

2: TSEC1-1

3: TSEC2-0

4: TSEC2-1

5: BMS

6: TLE

7: PCI64

8: FCFG

12 3 4 56 7 8

1 <- ->0

1: BOOT SEQ0 ON

2: BOOT SEQ1

3: ROMLOC0

4: ROMLOC1

5: ROMLOC2

6: DDRCM

7: LBIUCM

8: SWEN

12 3 4 56 7 8

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Freescale Semiconductor Page 5 of 8

Step 3.d: SW7 Configuration

Set 4

SW7.1-SW7.7: Core PLL setting

Sets the ratio between the e300 core clock and the internal csb_clk

Factory setting: ‘000010000’ for core_clk = 533MHz

Recommended secondary setting: ‘00000110’ for core_clk = 500MHz

SW7.8: Core disable

Factory setting: '0'; core enabled for boot operation

Factory default setting: 00001000

Step 3.e: SW2 Software Option SW2: Software option

Software BCS rotary-switch SW2 positions (0-7) enable program flow change

Switch status can be seen in BCSR10[2-4]

Factory setting: ‘0’

PCB

Step 3.f: SW5 Power Switch SW5: power switch

ON: power from an external 5V power supply via the P10 power jack

combined mode: powered from +5V on PIB power supply through riser

connectors (regardless of SW5 position)

board plugged as a PCI add-in card: PC internal power supply will provide 5V

via PCI edge connector (regardless of SW5 position)

Step 3.g: JP1:

Internal/External Clock

JP1

Selects the source for the CLOCKIN signal

• If a jumper is located between JP1 pins 1-2 (factory setting), the processor is

clocked from the on-board clock oscillator (U21 socket)

• If a jumper is located between JP1 pins 2-3, the processor is clocked from an

external source (via P5)

• The SHMOO mode clock source is I2C; manually programmed clock

synthesizer residing on PIB

Internal

Clock Source

External

Clock Source

1 <- ->0

1: COREPLL0 ON

2: COREPLL1

3: COREPLL2

4: COREPLL3

5: COREPLL4

6: COREPLL5

7: COREPLL6

8: COREDIS

12 3 4 56

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Page 6 of 8 Freescale Semiconductor

Step 4: Assemble and connect

the power supply kit.

Note:

Move power switch to OFF.

Assemble the AC/DC power supply kit:

• power cable with country-specific

wall outlet plug

• power supply unit and cable with jack

(for board connection)

1. Connect the AC/DC power supply

cable with jack to the board.

2. Plug the power cable into the wall

outlet.

AC/DC Power Supply

Power Supply Cable

ON/OFF Switch

Step 5: Perform initial board

power up.

Note:

To prevent damage to the JTAG

connectivity unit connect the unit

only after initial board reset.

1. Move the power switch to ON. LED1

briefly displays green light.

2. Check for completion of the reset

sequence-indicated by a single flash

of LED1 (green) and LED2 (red).

The location of LED1 and LED2 is

marked in the figure of Step 7 on

page 7.

3. Shut off the power-move the power

switch to OFF.

Step 6: Connect the JTAG

connectivity unit to the board.

The JTAG connectivity unit enables

CodeWarrior SW work with the

board.

1. Connect the JTAG connectivity unit

to the JTAG/COP 14-pin connector.

2. Move the power switch to ON.

3. Check for completion of the reset

sequence (see Step 5 on page 6).

4. Continue as per the instructions in

the Kit Configuration Guide.

JTAG/COP 14-Pin

Connector

CodeWarrior

USB TAP

MPC8349EA MDS

Processor Board

JTAG

Connectivity Unit

JTAG/COP 14-Pin

Connector

PC with

CodeWarrior

installed

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Freescale Semiconductor Page 7 of 8

Step 7: Attach remaining cables

to the board according to your

development needs.

Connect the remaining cables to the

board as per user development

needs and planned board use:

1. JTAG/COP connector for JTAG

connectivity unit-included in the

CodeWarrior SW kit

2. Serial port for the joined Freescale

adaptor cable with one RJ45 and

two RS232 connectors:

a RJ45 10-pin plug-plugs into the

serial port

b RS232 9-pin D-type connector

3. USB port for USB adaptor and

connector:

a mini USB adaptor: 5-pin (male)

and 4-pin (female)

b USB cable with two connectors:

standardA and miniB.

4. Ethernet ports for the two Ethernet

cables with RJ45-8 pin connectors.

JTAG/COP

Connector

Power Supply

Port

Reset LEDs

LED1 (green)

LED2 (red)

How to Reach Us:

USA/Europe/Locations Not Listed:

Freescale Semiconductor Literature Distribution

Center

P.O. Box 5405

Denver, Colorado 80217

1-800-521-6274 or 480-768-2130

Japan:

Freescale Semiconductor Japan Ltd.

Technical Information Center

3-20-1, Minami-Azabu, Minato-ku

Tokyo 106-8573, Japan

81-3-3440-3569

Asia/Pacific:

Freescale Semiconductor Hong Kong Ltd.

2 Dai King Street

Tai Po Industrial Estate

Tai Po, N.T., Hong Kong

852-26668334

Home Page:

www.freescale.com

Information in this document is provided solely to enable system and software implementers to use

Freescale Semiconductor products. There are no express or implied copyright licenses granted

hereunder to design or fabricate any integrated circuits or integrated circuits based on the information

in this document.

Freescale Semiconductor reserves the right to make changes without further notice to any products

herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the

suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any

liability arising out of the application or use of any product or circuit, and specifically disclaims any

and all liability, including without limitation consequential or incidental damages. “Typical” parameters

that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary

in different applications and actual performance may vary over time. All operating parameters,

including “Typicals”, must be validated for each customer application by customer’s technical

experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights

of others. Freescale Semiconductor products are not designed, intended, or authorized for use as

components in systems intended for surgical implant into the body, or other applications intended to

support or sustain life, or for any other application in which the failure of the Freescale Semiconductor

product could create a situation where personal injury or death may occur. Should Buyer purchase

or use Freescale Semiconductor products for any such unintended or unauthorized application,

Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries,

affiliates, and distributors harmless against all claims, costs, damages, and expenses, and

reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that Freescale

Semiconductor was negligent regarding the design or manufacture of the part.

Learn More: For more information about Freescale products, please visit www.freescale.com.

Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other

product or service names are the property of their respective owners.

MPC8349EA MDS Processor Board HW Getting Started Guide, Rev. A

Page 8 of 8 Freescale Semiconductor

Indice

Altri manuali Freescale Semiconductor Hardware per computer

Freescale Semiconductor

Freescale Semiconductor FRDM-K64F Manuale utente

Freescale Semiconductor

Freescale Semiconductor MCF5329 Manuale utente

Freescale Semiconductor

Freescale Semiconductor PowerQUICC III MPC8555E Manuale di istruzioni

Freescale Semiconductor

Freescale Semiconductor USB-KW24D512 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC8309 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC8260 PowerQUICC II Family Manuale utente

Freescale Semiconductor

Freescale Semiconductor MC68HC908MR16 Manuale utente

Freescale Semiconductor

Freescale Semiconductor ColdFire MCF52210ColdFire MCF52211ColdFire MCF52212ColdFire... Manuale utente

Freescale Semiconductor

Freescale Semiconductor 56F827 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC8272ADS Manuale utente

Freescale Semiconductor

Freescale Semiconductor i.MX 6SoloLite Linux Manuale utente

Freescale Semiconductor

Freescale Semiconductor NXP CodeWarrior USB TAP Manuale utente

Freescale Semiconductor

Freescale Semiconductor MED-EKG Manuale utente

Freescale Semiconductor

Freescale Semiconductor TWR-LS1021A Manuale utente

Freescale Semiconductor

Freescale Semiconductor Motorola MMDS0508 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MCF54455 Manuale utente

Freescale Semiconductor

Freescale Semiconductor e200z3 Manuale utente

Freescale Semiconductor

Freescale Semiconductor 802.15.4/Zigbee Manuale utente

Freescale Semiconductor

Freescale Semiconductor TWR-MPC8309 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MCF52277 Manuale utente

Freescale Semiconductor

Freescale Semiconductor Target Interface MMDS0508 Manuale utente

Freescale Semiconductor

Freescale Semiconductor TWR-K20D50M Manuale utente

Freescale Semiconductor

Freescale Semiconductor i.MX35 Manuale utente

Freescale Semiconductor

Freescale Semiconductor FRDM-KE06 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente