FRER IEC61850 Foglio di istruzioni

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 1 di/of 44

3 05/07/18 FW 3.0.0.3 edition S. Isella A. Miori

2 14/03/18 General revision S. Isella A. Miori

1 21/12/16 General revision S. Isella A. Miori

0 14/09/16 First edition S. Isella A. Miori

Rev. Data / Date Descrizione / Description Preparata / Prepared Approvata / Approved

1. GENERAL DESCRIPTION

1.1 Introduction

Some FRER meters can be optionally equipped with an integrated IEC61850 Gateway or, as an alternative, can use

an external IEC61850 / Modbus RTU Gateway.

1.2 Additional option

As an additional option, on the integrated Gateway, a Master RS485 Modbus interface can also be installed,

expanding the Gateway functionality to other meters only equipped with a Slave RS485 Modbus interface.

1.3 Available Versions

Both Gateway types, integrated and external, are available in different combinations regarding the maximum number

of meters that can be connected, the Set of available measured quantities, the number of Data Sets and Report

Control Blocks included in the default configuration, and allowed as maximum in each IED.

Max

Meters

Set of

measured

quantities (1)

Default Data

Sets for the

Gateway L.D.

(1)

Default Data

Sets for each

Meter L.D. (1)

Default Data

Sets for each

IED

Default RCB's

for each Data

Set (1)

Default RCB's

for each IED

Max allowed

Data Sets for

each IED

Max allowed

RCB's for each

IED

1 Full 1 4 5 4 20 6 24

4 Full 0 3 12 2 24 12 24

6 Reduced 0 3 18 1 18 18 24

Note (1): See chapter 5 "IEC61850 SERVER" for further details

1.4 Special considerations regarding the measurements updating time

The IEC61850 Gateway performs 3 basic operations in sequence:

Fetching of the measurements data from the meter.

Evaluating if the measurements data have changed more than the preset deadbands and, in case, updating

the relevant Data Sets.

Sending the Reports to the subscribed clients, according to the triggering options they have chosen.

This sequence is repeated, in a cyclical way, for each meter connected to the Gateway.

The time needed to complete the sequence for a single meter, depends on many factors, but the most relevant are:

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 2 di/of 44

the variability of the measured quantities

the number of subscribed RCB's by the IEC61850 clients.

When the measured variables are in a steady state (they don't vary more than the deadbands), and no RCB's have

been subscribed, the time required to complete the full sequence for each meter is around 450ms.

When all the measured variables change, from cycle to cycle, more than the deadbands, then each subscribed RCB's

adds about 100ms to the sequence time for each meter.

In application where update time is a concern, the "Single Meter" version of the Gateway should be preferred to both

"4 and 6 Meters" versions, the Data Sets should be kept as few and small as possible, the deadbands should be set

as wide as possible, and the number of subscribed Report Control Blocks should be as low as possible.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 3 di/of 44

2. BASIC COMMISSIONING

2.1 Introduction

Before fully configure the devices, after that the proper hardware and electrical installation have been completed (see

the installation manual and/or the terminals label for each specific product), and the devices have been powered-on,

some operations must be carried out in the following order.

2.2 What you needed

Check to have got the following items from FRER (they are in a small CD included in the package, or you can obtain

them from the FRER support):

a) "Gateway Tracker" utility installation file.

"Gateway Tracker" is an utility to identify the devices on a network, to set their IP addresses, to update them to

the latest firmware release, and to upload and download special files to and from the devices, if requested by

the FRER support.

Install it on your laptop or desktop PC.

b) Latest available firmware release.

It is recommended that the firmware of the devices is upgraded to the latest release before commissioning

them.

Note: In case of devices with firmware release lower than 3.0.0.3, this is mandatory, due to both important

performance and features improvements, and bug fixes.

Contact FRER support to be sure to have obtained the latest available firmware release: you will be asked to

specify the Gateway version (Single, 4, or 6 Meters) and the last five digits of the MAC address (you can read

them on the label of the Gateway, or by the "Gateway Tracker" Utility

You will receive from FRER support a file containing the latest firmware release, which may have a name

similar to GW1_3_0_0_3.hex (for the "Single Meter" version), to GW4_3_0_0_3.hex (for the "4 Meters"

version) or to GW6_3_0_0_3.hex (for the "6 Meters" version).

Note: In case you have different Gateway versions, be careful to use the right firmware file for the right Gateway

version, otherwise at the end of the process the Gateway will be unusable.

2.3 Settings by the front display and front panel panel push-buttons

For each meter connected to the IEC61850 Gateway (including the single one which integrates the gateway itself):

a) Enter the configuration menu (as described in the specific user manual).

b) Set the correct VT's and CT's ratios (they can also be further modified later, but this requires the repetition of

the meter configuration in the configuration Web-Server -see later on paragraph 2.5 "Operations with the

Configuration Web-Server"-).

c) Set the following communication parameters:

Device logic address: between 1 and 247.

Baud rate: 19200.

Parity: Even.

Stop bits: 1.

d) Exit the configuration menu confirming changes, if requested by the meters.

Note: All meters connected to the same Gateway must be set with the same communication parameters, except the

device logic address, which must be different for each one of them.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 4 di/of 44

2.4 Operations with the "Gateway Tracker" utility

a) Start the "Gateway Tracker utility", a windows opens showing a list of Gateways connected to the local

network.

Note: The factory IP settings of the Gateways are the following:

- IP address: 192.168.1.10

- Subnet mask: 255.255.255.0

- Default gateway: 192.168.1.1

Note: The Gateways must belong to the same network broadcast domain of the PC, in order to be revealed.

Note: Always avoid wireless connections, use only connections with Ethernet cable.

b) Right click on the first Gateway of the list, and then select the menu item "IP configuration":

c) Set the addresses of your choice and press OK:

d) Repeat the same process for all the Gateways in the list.

Note: All devices must be assigned with a unique IP address, and no conflicting IP addresses can exist with other

devices on the network.

Note: The assigned IP addresses must belong to the same sub-network of the PC, otherwise the following step

"Upload image" will not work.

Note: If an IP conflict exists on the network, the following step "Upload image" may leave the Gateway unusable, to be

returned to the factory for repairing.

Note: In the following step "Upload image", after the upload of an image has been completed, the relevant Gateway

will revert to its factory default IP settings: check that these settings do not conflict with those of any other

Gateway on the network.

Note: The simplest way to avoid conflicting IP settings during these operations, is to physically connect one by one the

Gateways directly to the PC.

Note: The Ethernet port of the Gateways has no auto MDI/MDIX switching function, so you may need a crossed

Ethernet cable or you may need to connect the devices to an Ethernet port supporting the auto MDI/MDIX

switching.

e) Once you have properly set the IP addresses, right click on the first Gateway of the list, and then select the

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 5 di/of 44

menu item "Upload image ":

f) Select the upgrade file, containing the latest firmware release, that you have received from Frer support, and

press "Open":

g) You will receive the following warning message, and press "OK":

h) Wait that the progress bar indicating the progress status will reach the end, until you will get the following

confirmation message:

Note: After the upload of an image has been completed, the relevant Gateway will revert to its default IP settings:

check that these settings do not conflict with those of any other Gateway on the network.

i) Repeat the same process for all the Gateways in the list.

j) Re-set the correct IP addresses again, according to your needs, as shown in points b) to d).

k) Close the "Gateway Tracker" utility when done.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 6 di/of 44

2.5 Operations with the Configuration Web-Server

a) Using a web browser of your choice, type in the address bar the IP address of the gateway you want

configure, the following home page will appear:

b) Press the "Meters configuration" menu item, and enter the credentials in the following login panel:

Note: The factory default credentials are:

- Username: admin

- Password: password

c) Press the "Autodiscovery" button, then "Start", and then "OK" to the successive confirmation message:

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 7 di/of 44

d) Press the "Save" button when the autodiscovery function will have discovered all meters connected to the

Gateway (their quantity changes depending on the Gateway version ("Single, 4 or 6 Meters")

e) And then confirm reboot, which is needed to create the proper IID file.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 8 di/of 44

f) Wait a couple of minutes to allow the server completing the reboot process, then press "Device statistics" on

the home page to get confirmation that the IEC61850 server is properly running:

g) Repeat the same process for all the other Gateways.

h) Close the Configuration Web-Server when done.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 9 di/of 44

3. CONFIGURATION WEB-SERVER

3.1 Introduction

Each IEC61850 Gateway is equipped with an integrated Configuration Web-Server (accessible by typing its IP

address on the address bar of any web browser of your choice), used to configure some functional details of the

Gateway itself, and some behaviors of the IEC61850 protocol stack, and to monitor, in the commissioning process, the

correct operation of the system.

The following is a detailed description of all the settings, grouped by the main menu items found on the left side of the

main page.

Every settings change made by the operator, needs to be saved (by pressing the "Save" button on the page) and will

became operative after a reboot of the system (a reboot will be automatically proposed after having pressed the

"Save" button).

However, all modifications introduced in a single settings page can be "cumulated" in a single saving, and all

modifications in all pages can be "cumulated" in a single reboot, unless a change in one setting affects the operation

of another setting (this is the case, for example, when one changes the communication parameters of the serial link,

which will be used in the "Meters configuration" page to identify the meters connected to the Gateway).

Note: Some settings need to be transferred to the IID file; they are:

- IP settings

- IED name

- Deadbands

- Any change in "Meters configuration"

In this case, a new IID file must be created, which will overwrite the IID or CID file currently in use.

When a CID file is loaded in the IEC61850 Server, these settings will reflect those contained in the CID file, and

could not be modified anymore unless the server is allowed to replace the current CID file with a newly

generated IID file (see paragraph 3.2.3 "IEC61850" for further details).

Note: The Configuration Web-Server heavily interferes with the operation of the IEC61850 Server, specially with those

pages which continuously update their content (Data monitor and Device statistics): its use must be limited to

the minimum required during commissioning, and should be avoided during normal operation of the IEC61850

Server

Note: Only one session of the Configuration Web-Server is allowed at a time.

IEC61850 GATEWAY

CONFIGURATION MANUAL

No. Ipm0218_3

Pag./Page 10 di/of 44

3.2 General settings

This page contains some sub-pages, they are described one by one.

3.2.1 Network

IP Configuration:

In this section the IP address, Subnet mask and Default gateway of the server can be set or, as an alternative, the

DHCP client can be enabled, which retrieves automatically these settings from a DHCP client on the network.

The factory IP settings of the Gateways are the following:

- IP address: 192.168.1.10

- Subnet mask: 255.255.255.0

- Default gateway: 192.168.1.1

Note: Since the gateway will be used as IEC61850 server, it is advisable not to use DHCP, but manually assign fixed

IP settings.

Note: IP settings affect both the IEC61850 Server operation (they will be also included in the IID file) and the

Configuration Web-server operation; therefore it is not possible to have different IP settings for the IEC61850

Server and for the Configuration Web-server.

Note: When a CID file is loaded in the IEC61850 Server, these settings will reflect those contained in the CID file, and

could not be modified anymore unless the server is allowed to replace the current CID file with a new generated

IID file (see paragraph 3.2.3 "IEC61850" for further details).

DNS:

In this section the Primary and Secondary DNS servers can be set.

Note: DNS servers are used only if the NTP is enabled, and the NTP servers are specified with their URL instead of

their IP addresses. (see next section for further details).

User-defined NTP Server

If "Use NTP" check-box is checked, at boot time and then every one hour, the date and time will be automatically

retrieved from the specified NTP servers, and the internal RTC will be adjusted accordingly.

Indice

Altri manuali FRER Portale

FRER

FRER MCIMIDETH Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente