Frymaster Cooking Computer KFC-1 SMS Manuale utente
Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
24-Hour Service Hotline 1-800-551-8633
FEB 2001
8195733
KFC-1 SMS Cooking Computer
USER GUIDE
1-1
KFC-1 SMS COMPUTER
CHAPTER 1: IMPORTANT INFORMATION
1.1 General
The KFC-1 SMS Cooking Computer is designed to operate with both full- and split-pot fryers. For
a full-pot fryer, turn the computer on by pressing either switch. For split-pot fryers, press the
left switch to operate the left pot and the right switch to operate the right pot.
The KFC-1 SMS Cooking Computer is designed to control either single or
multiple cooking cycles. The computer has 10 product buttons, which can be
individually programmed with up to 10 cooking intervals, three pre-alarms, and
straight or flex time for each product. The KFC-1 SMS can track the number of
heads cooked by the fryer and calculate recovery time. Also, the KFC-1 SMS
can be programmed to calculate recovery time and the number of cook cycles
since the last filtering. It is used on Frymaster KJ3FC, KSCF18G, and
KSCFH18E open fryers and can be programmed for heat curves for any product.
It is designed to operate in both full-pot and split-pot fryers. The KFC-1 SMS also has shortening
management programming and an internal real time clock.
If power outages of less than 5 seconds occur, KFC-1 SMS computers will automatically return to
current operational status once power is restored. If the computer fails to return to the current
operation when power is restored, reset the computer by unplugging the fryer from the power
source. The computer should reset when the fryer is plugged back in, and this, many times,
eliminates costly, unneeded service calls.
1.2 Service Information
Call the “800” number on the cover of this manual for the location of your nearest maintenance &
repair center. When requesting service assistance, always give the model and serial numbers of your
cooking computer and the type of fryer this cooking computer is installed on.
To assist you more efficiently, the following information will be needed:
Model Number
Serial Number
Type of Fryer
Nature of the
Problem
Any other information which may be helpful in solving your service problem.
NOTE:
Activation of
the oil management
system is optional. All
other features of the
KFC-1 SMS remain
operational with the
oil management
programming idle.
1-2
1.3 KFC-1 SMS Computer Controls
KFC-1 SMS Computer
Button Function
On/Off
Turns the fryer ON and OFF.
For a full-pot fryer, press either ON/OFF switch to turn the computer on.
For a split-pot fryer, press the left ON/OFF switch to operate the left pot and
press the right ON/OFF switch to operate the right pot.
Product Buttons
Each of the 10 product buttons selects a cook cycle, starts the cycle, cancels the
cycle, and stops the end-of-cycle alarm. A flashing LED above the product
number indicates that product has been selected.
In programming mode, these buttons are used to select the head count, cook
time, setpoint, flex, and alarm settings.
1-3
1.3 KFC-1 SMS Computer Controls (cont.)
Button Function
Program Scan
Shows the remaining cook time for other active cook cycles when operating in
the multiple cook cycle mode.
In programming mode, this button activates programming mode, and
advances through the programming steps.
Enter
Shows the remaining cook time.
In programming mode, this button is pressed to move to the next step in the
programming sequence.
Temp
Shows the actual fryer temperature.
Pressing twice will show programmed setpoint temperature. Pressing three times
will show time.
In programming mode, this button is pressed to select menu options.
Exit/Cool Filter
Returns the computer and fryer from the standby mode to normal operating
mode.
During Filter Lockout Mode, pressing this button returns fryer and computer to
the setback mode once filtering has been completed. During operating mode,
press left Exit/Cool Filter to view time.
1-4
1.4 Morning (AM) Polishing Cycle
1
2
3
4
5
Computer display changes to PLSH.
When the fryer reaches filtration setpoint, the display alternates between START and
PLSH.
Press EXIT/COOL FILTER button on computer
face.
Assemble filter. Sprinkle 8 ounces
of filter powder over filter paper in
filter pan.
Open drain valve. Turn pump ON. Computer displaysPLSH 30:00 to polish shortening for 30 min.
Computer
ON/OFF button
to turn fryer ON.
1-5
1.4 Morning (AM) Polishing Cycle (cont.)
6
Computer counts down. Polishing lasts 30 minutes.
7
8
9
10
Computer displays FILL
and an alarm sounds.
Press Exit/Cool Filter to
shut off alarm.
Cool appears in right display.
Press
EXIT/COOL
FILTER
button
Computer displays oil temperature
and fryer heats to setpoint. Fryer displays drop when it’s at
setpoint and ready to cook.
Close drain
valve. Pump
shortening into
frypot. Turn
pump OFF.
Press
EXIT/COOL
FILTER
button
1-6
1.5 Afternoon (PM) Polishing Cycle
1Assemble filter. Sprinkle filter powder over filter paper in filter pan.
2
3
4
At 2 p.m. an alarm sounds and computer display alternates between START and PLSH.
Press EXIT/COOL FILTER button on computer
face to shut off alarm.
Open drain valve. Turn pump ON. Computer displays PLSH 30:00 to polish shortening for 30 minutes.
1-7
1.5 Afternoon (PM) Polishing Cycle (cont.)
5
Computer counts down.
6
7
8
9
At the end of the polishing
cycle, the computer displays
FILL and an alarm sounds.
Press Exit/Cool Filter to shut
off alarm.
COOL appears in right display.
Computer displays LOW and fryer
heats to setpoint. Fryer displays DROP when
oil/shortening temperature is at
setpoint and ready to cook.
Press
EXIT/COOL
FILTER
button
Press
EXIT/COOL
FILTER
button
Close drain valve.
Turn pump off.
Pump shortening into
frypot.
1-8
1.6 Delaying Afternoon (PM) Polishing Cycle
1
2
3
4
5Press any program button. The fryer will cook normally until the preprogrammed delay period expires.
The polish can only be delayed once. Polish must be performed within three-hour period or the controller
will go into polish lockout.
At 2 p.m. an alarm sounds and computer display alternates between START and PLSH.
Press EXIT/COOL FILTER button on computer
face and fryer returns to Drop mode.
Press and hold PROG SCAN and ENTER buttons for five seconds.
Display alternates between DYPL and the oil temperature.
1-9
1.7 Using Polish Now Feature
1
2Assemble filter. Sprinkle 8 ounces of filter powder over filter paper in filter pan.
3
4
Computer displays START and PLSH.
5
Computer display alternates between DYPL and temperature display, indicating the polish
cycle has been delayed.
Press and hold both EXIT/COOL FILTER buttons
on computer face.
Press EXIT/COOL FILTER button on computer face to
shut off alarm.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Frymaster Scrivania
