FS FS-AC32 Manuale utente
ENTERPRISE WIRELESS LAN CONTROLLER
WIRELESS LAN CONTROLLER FÜR UNTERNEHMEN
CONTRÔLEUR LAN SANS FIL POUR ENTREPRISE
Quick Start Guide V1.0
Quick-Start Anleitung
Guide de Démarrage Rapide
FS-AC32
Introduction
Accessories
Hardware Overview
FS-AC32
Thank you for choosing the enterprise wireless LAN controller. The guide is designed to familiarize you
with the layout of the wireless LAN controller and describes how to deploy the wireless LAN controller
in your network.
EN
M4 Screw x 8Power Cord x 1
CONSOLE USB
MGMT
RJ45
Mounting Bracket x 2
10/100/1000BASE-T ports for Ethernet connection
A RJ45 console port for serial management
An Ethernet management port
Port Description
RJ45
CONSOLE
MGMT
A USB management port for software and configuration backup and
offline software upgrade
USB
Front Panel Ports
1
Installation Requirements
Back Panel Button
Front Panel LEDs
Before you begin the installation, make sure that you have the following:
EN
The power module is not in the position or fails.Off
Solid Green
Solid Red
The power module is operational.
The hard drive is reading and writing.
LED indicator Status Description
Control the controller power on or off.
PWR
HDD
PWR
HDD
Button Description
Power ON/OFF
USEONLY WITH 250V FUSE
110-220VAC 50-60Hz
ON
OFF
VGA ON/OFF Power Supply
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables and fiber optical cables for connecting network
devices.
2
Mounting the Wireless LAN Controller
Site Environment
Desk Mounting
Do not place the controller in a damp/wet location.
Keep the controller far away from the heat source.
Ensure that the controller is properly grounded.
Wear an anti-static wrist strap during installation and maintenance.
Put the tools and parts away from where people walk by.
Use UPS (Uninterruptible Power Supply) to prevent power failure and other interferences.
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
EN
3
Rack Mounting
1. Secure the mounting brackets on the two sides of the controller with six M4 screws.
2. Attach the controller to the rack using four M6 screws and cage nuts.
EN
4
Grounding the Controller
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
controller is mounted.
2. Secure the grounding lug to the grounding point on the controller back panel with the washers
and screws.
Connecting the Power
1. Plug the AC power cord into the power port on the back of the controller.
2. Connect the other end of the power cord to an AC power source.
CAUTION:Do not install the power cord while the power is on, and when the power cord
is connected, the fan will start to operate whether the power button is on or off.
EN
5
Connecting the RJ45 Ports
Connecting the Console Port
1. Connect an Ethernet cable to the RJ45 port of a computer or other network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the controller.
1. Insert the RJ45 connector into the RJ45 console port on the front of the controller.
2. Connect the DB9 female connector of the console cable to RS-232 serial port on the computer.
EN
6
Configuring the Wireless LAN Controller
Configuring the Controller Using the Web-based Interface
Connecting the MGMT Port
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the MGMT port on the front of the controller.
Step 1: Connect the computer to the Management port of the controller using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. (“x” is any number from 2 to 254.)
?x
OK Cancel
General
IP address:
Subnet mask:
Default ga t e wa y :
You can get IP settings assigned automatically if your net w o r k
supports this capabil i t y . O t herwise, y o u need t o a sk your net w o r k
adminis t r a t o r f o r the appropr i a t e IP settings .
In ter net Pro toc ol Version 4 ( T CP/IP v4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit A d v anc e d ...
. . .21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNSserv er addre ss automatically
Use the following DNS se rve r addresses:
EN
7
Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password,
admin/admin.
Step 4: Click Login to display the web-based configuration page.
Simplified Chinese
Login
Wireless Controller
admin
*****
Configuring the Controller Using the Console Port
Step 1: Connect a computer to the controller's console port using the supplied console cable.
Step 2: Start the terminal simulation software such as HyperTerminal on the computer.
Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1 stop bit
and no flow control.
Step 4: After setting the parameters, click Connect to enter.
x
Quick Connect
Protocol:
The port may be manually entered or selected from the list.
Serial
Flow Control
DTR/DSR
RTS/CTS
XON/XOFF
Save sessionShow quick connect on startup
Open in a tab
Connect
Cancel
COM3
9600
8
None
1
Port:
Baud rate:
Data bits:
Parity:
Stop bits:
Name of pipe:
EN
8
The Screen Displays Request Timed Out
Troubleshooting
1. Check if the network cable is intact.
2. Check if the hardware connection is correct.
3. The system status indicator on the device panel and the NIC indicator on the computer must be lit.
4. The computer's IP address setting is correct.
Support and Other Resources
Download
Help Center
Contact Us
https://www.fs.com/products_support.html
https://www.fs.com/service/fs_support.html
https://www.fs.com/contact_us.html
Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a
free return within 30 days from the day you receive your goods. This excludes any custom made items
or tailored solutions.
Warranty: The Wireless LAN Controller enjoys 3 years limited warranty against defect in
materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html
3
EN
9
Indice
Lingue:
Altri manuali FS Controllori
