FSK TCP 0211 Manuale utente
MULTI-ROUTER
TCP 0211
INSTALLATION &
OPERATION MANUAL
TABLE OF CONTENTS
OVERVIEW ............................................................................................................... 2
FEATURES OF THE TCP MULTI-ROUTER .................................................................... 2
INSTALLATION ......................................................................................................... 3
ANTENNA .................................................................................................................. 3
GSM ANTENNAS........................................................................................................ 4
RS232 ........................................................................................................................ 4
PRINTER..................................................................................................................... 4
FUSE .......................................................................................................................... 4
OPERATION.............................................................................................................. 4
DATE / TIME .............................................................................................................. 5
GSM STATUS ............................................................................................................. 5
CONFIGURATION MENU ........................................................................................... 7
IP ADDRESS ............................................................................................................... 7
SUBNET MASK ........................................................................................................... 8
GATEWAY 1 ............................................................................................................... 8
GATEWAY 2 ............................................................................................................... 9
SERIAL OUT ............................................................................................................... 9
BUZZER.................................................................................................................... 10
SERVER 1 ................................................................................................................. 10
LIMIT MODE ............................................................................................................ 11
DHCP ....................................................................................................................... 12
PRINTER................................................................................................................... 12
APPENDIX A - RS232 CONNECTIONS AND PROTOCOL .................................... 14
APPENDIX B - FSK ALARM CODES...................................................................... 16
APPENDIX C - PRINTER CONNECTIONS ............................................................. 26
APPENDIX D –ROUTER SPECIFICATIONS.......................................................... 27
LIMITED WARRANTEE......................................................................................... 28
2 | P a g e
1. OVERVIEW
The FSK Router 0211 is a high performance Repeater or Base Station for use on the
FSK long-range radio and GSM networks.
When installed as a base station in the security control room, it will receive alarms
from FSK long-range radio transmitters and GSM units
It has the facility to display the alarm, print it, and send it to the monitoring
computer by means of a serial connection.
When installed as a repeater, it will forward alarms from FSK long-range radio
transmitters to the control room via either radio, GSM or any TCP/IP broad-band
connection to the control room.
The Router 0211 is self-contained and has its own power supply and a backup
battery.
The Router 0211 is programmed using the FSK Router Programming software via a
serial port or remotely (if used on the FSK GSM or TCP/IP networks).
Some of the Router 0211 settings can be changed via the on-board keypad.
2. FEATURES OF THE TCP MULTI-ROUTER
FSK High-performance long-range radio receiver.
FSK Radio Transmitter (repeater only).
Option of dual 3G high-speed GSM modem.
Ethernet TCP/IP port.
Large LCD to display alarms or settings.
Keypad for changing settings as well as performing diagnostics.
On-board power supply with backup battery.
Printer Port (parallel).
Serial ports for programming as well as connections to a monitoring
computer.
3 | P a g e
3. INSTALLATION
The Router 0211 is connected as shown
(ROUTER REAR VIEW)
Connect the Radio Antenna using a PL259 (UHF) 50Ω RF Connector.
Connect the RS232 (monitoring computer) plug to the monitoring
computer using the serial cable supplied.
Plug a printer (if required) into the printer port.
Install the 10A fuse into the fuse holder.
Plug the Ethernet Connector into the Ethernet Switch (if used).
Connect the GSM antennas to the unit. The connectors are the SMA type.
Connect the Power input to a 220V AC mains supply.
ANTENNA
The antenna is crucial to the optimum performance of the
Router. Suitable antennas are
Folded Dipole (outdoor type)
Collinear
The antenna should be mounted outdoors on a mast (as high
as possible) in order to achieve maximum radio range. The
antenna should be connected using RG213 or RG214 cable. RG58 cable is not
suitable for runs of more than 10m as it has too much loss.
The antenna should be mounted vertically (vertical polarisation) and not
horizontally.
GSM ANTENNAS
MTN VODACOM
RADIO ANTENNA
BOOTLOADER
SWITCH
RS232
MONITORING
COMPUTER
RS232
PROGRAMMING
PRINTER
ETHERNET
USB
FUSE
(DC 10A) 220VAC
4 | P a g e
GSM ANTENNAS
If the Router is fitted with a GSM Module, GSM antennas should be plugged into
the unit. The antenna connector is a SMA type. The antenna should preferably be
mounted externally to the control room. The antenna should be mounted so that
the GSM signal strength is greater than 24 (see the section on GSM).
RS232
The RS232 connection is used to send an incoming alarm to the monitoring
computer at the control room. The bottom RS232 connector is connected to the
computer. The RS232 should be connected using the cable supplied. The RS232
connections are as shown in Appendix A.
The Router has three alarm formats which can be transmitted using the serial port,
FSK Standard, FSK Extended or FSK7 (Contact ID). Refer to Appendix A.
Be sure that the correct format has been chosen (refer to the section on
Programming). The monitoring software should be compatible with the selected
RS232 format.
PRINTER
If a printer is required, it is connected via the DB25 (male) to Centronix cable
required. A purpose-made printer cable should always be used. Do not attempt to
make your own.
The standard printer connections are shown in Appendix B.
Note that a printer will slow down the operation of receiving a large number of
alarms (2+ alarms per second) due to the slow nature of the printer.
FUSE
The fuse is used to protect the internal circuitry from the battery in the event of a
failure. Only use a 20mm glass, 10A, Fast Blow fuse.
4. OPERATION
5 | P a g e
CONFIGURATION
A number of settings on the Router can be changed via the keypad and the LCD.
Be careful when changing settings as you may adversely affect the working of the
Router and its ability to receive and transmit alarms.
1. To change the configuration of the Router, press the ENTER (←) key.
2. The menus can be navigated using the UP (˄) and DOWN (˅) cursors.
3. The ENTER key is used to enter a menu or to enter the data.
Configuration screen
CONFIGURATION MENU –See Below
DATE/TIME
DATE: The date is entered as CCYY/MM/DD
Use the (E) key to advance to the next field
Press ENTER when done
TIME: The time is entered as HH:MM:SS
Use the (E) key to advance to the next field
Press ENTER when done
GSM STATUS
For models fitted with a GSM modem:
6 | P a g e
Press Enter to Display the GSM status:
The GSM status will cycle between the statuses of the two SIM cards installed on
the GSM modem. The Following information is displayed (per SIM card):
DEVICE ID This is the ID of the device on the FSK GSM network
SIG Signal Strength (S0 to S31). Minimum allowable = 20
BER Bit Error Rate (E0 to E99) 0 is optimal 99 is no value obtained
from the network
IP ADDRESS The IP address of this device on the FSK GSM Network
GPRS GPRS connected (GPRS-C) /not connected (GPRS-N)
SIM The status of the SIM card
SIM-OK (SIM card OK)
SIM-ER (SIM Card Error)
STATE Connected State
START (Initialising on GSM network)
READY (connected to FSK routing server)
GSMREG GSM Registration State
GSM-REG (Registered on the GSM network)
GSM-OFF (Not Registered)
GPRSREG Data Registration State
GPRS-REG (Registered on 3G/Edge/GPRS)
GPRS-OFF (Not registered on GSM data)
7 | P a g e
Press the CLEAR button to exit the menu
CONFIGURATION MENU:
Press Enter to access the configuration menu:
IP ADDRESS
The IP address is 10.0.0.31
8 | P a g e
Enter the IP address with leading zeros, e.g. 10 is entered as 010.
Use the (E) key to advance on field.
Press Enter when done.
SUBNET MASK
The Subnet Mask is 255.255.255.0.
Enter the Subnet Mask with leading zeros, e.g. 10 is entered as 010.
Use the (E) key to advance on field.
Press Enter when done.
GATEWAY 1
Gateway 1 is 10.0.0.1.
Enter the Gateway with leading zeros, e.g. 10 is entered as 010.
Use the (E) key to advance on field.
Press Enter when done.
9 | P a g e
GATEWAY 2
Gateway 2 is 10.0.0.2.
Enter the Gateway with leading zeros, e.g. 10 is entered as 010.
Use the (E) key to advance on field.
Press Enter when done.
SERIAL OUT
The Serial Output format is used to send alarms to the Control Room Computer via
the RS232 port.
Use the UP and DOWN arrows to cycle between the following Serial Output
formats:
FSK 7
FSK
FSK EXTENDED
Refer to Appendix A for the descriptions of the Serial Output formats.
FSK 7 is the preferred Serial Format.
MAKE SURE THAT THE CORRECT SERIAL FORMAT IS SELECTED OR THE
MONITORING COMPUTER WILL NOT RECEIVE ANY ALARMS
Indice
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza