FSR Flex-IO16 Guida all'installazione

Flex-IO Builder

Installation and Operating Guide

Based on firmware revision 1.22

244 Bergen Blvd. Woodland Park NJ 07424 973-785-4347

43088 LIT1547B

PROPRIETARY INFORMATION

All information in this manual is proprietary to and the property of FSR Inc. This publication is

be reproduced, transcribed, or transmitted, in any form or by any means, without prior explicit

written permission from FSR Inc.

Specifications may be changed without any notice in order to improve

the function of the product.

LIMITED WARRANTY

The FLEX-IO16 module is warranted against failures due to defective parts or faulty

workmanship for a period of three years after delivery to the original owner. During this period,

FSR will make any necessary repairs or replace the unit without charge for parts or labor.

Shipping charges to the factory or repair station must be prepaid by the owner, return-shipping

charges (via UPS Ground) will be paid by FSR.

This warranty applies only to the original owner and is not transferable. In addition, it does not

apply to repairs done by other than the FSR factory or Authorized Repair Stations.

This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected to

physical abuse or has been modified in any way without written authorization from FSR. FSR’s

liability under this warranty is limited to repair or replacement of the defective unit.

FSR will not be responsible for incidental or consequential damages resulting from the use or

misuse of its products. Some states do not allow the exclusion of incidental or consequential

damages, so the above limitations may not apply to you. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state.

Warranty claims should be accompanied by a copy of the original purchase invoice showing the

purchase date (if a Warranty Registration Card was mailed in at the time of purchase, this is not

necessary). Before returning any equipment for repair, please read the important information on

service below.

SERVICE

Before returning any equipment for repair, please be sure that it is adequately packed and

cushioned against damage in shipment, and that it is insured. We suggest that you save the

original packaging and use it to ship the product for servicing.Also, please enclose a note giving

your name, address, phone number and a description of the problem.

NOTE: all equipment being returned for repair must have a Return authorization (RMA) Number.

To get a RMA Number, please call the FSR Service Department (1-800-332-FSR1). Please

display your RMA Number prominently on the front of all packages.

CONTACT INFORMATION

FSR INC.

244 Bergen Blvd.

Woodland Park, NJ 07424

Phone: (973) 785-4347

Order Desk Fax: (973) 785-4207

E-mail: [email protected]

Web Site: www.fsrinc.com

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be damaged by

electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection

systems is highly recommended in order to protect and extend the life of your

equipment.

SAFETY

All the safety and user manual should be read before the appliance is operated.

The safety and operating instructions should be retained for future reference.

Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Do not use this equipment near wet place.

This product should be operated only from the type of power sources indicated

on the marking label. If you are not sure of the type of power supplied to your

home, consult your local power company.

This equipment may be equipped with a 3 wire grounding-type plug, a plug

having a third (grounding) pin. This pin will only fit in to a grounding type power

outlet. This is a safety feature. If you are unable to insert the plug in to the outlet,

contact your electrician to replace your obsolete outlet. Do not defeat the safety

purpose of the grounding-type plug.

Openings on the case are provided for ventilation and to ensure reliable

operation of the equipment and to protect it from overheating. The openings

should never be blocked.

Do not use any damaged power cords or plugs, or loosed outlets, this may cause

electrical shock or fire.

Do not put heavy articles such as other equipment on this product. Keep it away

from liquid, magnetic and flammable substances.

CONTENTS

PROPRIETARY INFORMATION..................................................................................................2

LIMITED WARRANTY..................................................................................................................3

SAFETY........................................................................................................................................4

DESCRIPTION .............................................................................................................................6

FEATURES...................................................................................................................................7

APPLICATIONS............................................................................................................................7

INSTALLATION CHECKLIST.......................................................................................................8

SERIAL CONNECTION DETAILS ..........................................................................................10

ETHERNET CONNECTION DETAILS....................................................................................10

USAGE AND TROUBLE SHOOTING.........................................................................................11

PING TEST FOR ETHERNET ................................................................................................13

EXAMPLE OF SUCCESSFUL CONNECTION VIA TCP/IP....................................................15

FIRMWARE VERSION AND BOOTCODE VERSION STRINGS ...........................................16

FIRMWARE UPGRADE PROCEDURE..................................................................................17

FLEX-IO BUILDER .....................................................................................................................22

NEW PROJECT......................................................................................................................22

ENTERING CHANNEL COMMANDS .....................................................................................25

SAVE PROJECT.....................................................................................................................27

OPEN AN EXISTING PROJECT.............................................................................................28

DOWNLOADING PROJECT TO FLEX-IO..............................................................................30

UPLOADING PROJECT FROM FLEX-IO...............................................................................35

FLEX-IO ACTION COMMANDS.................................................................................................36

GPI..........................................................................................................................................36

GPO ........................................................................................................................................37

WAIT .......................................................................................................................................37

SER COMMAND.....................................................................................................................38

IP INLINE ACTION..................................................................................................................38

IP COMMAND.........................................................................................................................38

DIMENSIONS.............................................................................................................................39

SPECIFICATIONS......................................................................................................................41

DESCRIPTION

The Flex-IO16 is a fully programmable control system component that provides an interface

between virtually any equipment having an RS-232 or Ethernet port and an external control

panel with up to 16 switches and lamps. This extremely versatile unit can be used to expand the

IO capabilities of the FSR Flex-LT control products or any 3rd party control system. It can also

be used to add IP connectivity to equipment that only has an RS- 232 port.

Configuration of the Flex-IO16 is accomplished through the use of the Flex-IO Builder GUI. The

Flex-IO builder can create, edit, debug, upload and download projects, and can also be used to

verify wiring and control in installed systems. The Flex-IO builder connects to the Flex-IO16 via

the second dedicated RS-232 “Program” port, or Ethernet.

Each of the 16 switch inputs can be configured to execute command strings up to 250

characters in length upon the press, hold, or release of the switch, or they can alternate

between two different strings when set to alternate action mode. The 16 lamp outputs can be

independently configured to turn on, off, blink or toggle state in response any of the switch input

events, or they can be remotely commanded via serial or IP. The short circuit

protection and automatic reset feature of the lamp outputs makes the Flex-IO16 very robust and

prevents damage due to typical field wiring errors. High output drive capability allows direct

control of external 12 volt relays.

The unit can be powered locally with an external IT-PS1 12 volt supply, or remotely via POE

from a POE network switch or midspan injector.

More complex control requirements can be satisfied by combining the Flex-IO16 with any of the

Flex-LT control products using virtual switch commands to the Flex-LT.

The FLEX-IO16 I/O Expansion Unit can be used with the FSR HuddleVU HV-T6 and HV-T3

Table Box models to convert button presses into serial or IP commands. This allows control of

various devices within a FLEX Controlled environment, while also providing LED feedback.

When used in conjunction with FSR’s line of T3-MJ Table Mic Boxes, you can easily connect up

to 16 boxes and have LED feedback when the mute circuits are activated on a 3rd Party DSP

Controller.

FEATURES

• 16 switch inputs

• Accommodates momentary or maintained N.O.

or N.C. switches

• 16 Lamp/Relay drive outputs with short circuit

protection/auto-reset feature

• Power locally or via POE Ethernet

• Configure via Serial or IP

• Full featured GUI supports system configuration & debug

• Independent serial ports for Program and Control

• Indicators for serial/IP activity, power and status

• Fully programmable

APPLICATIONS

• Add IP capability to legacy RS-232 equipment

• General purpose interface between hardwired

control panels and AV equipment

• I/O expansion for Flex-LT controllers

• Expansion unit for HuddleVU collaboration system

• Contact closure to RS-232 interface

• Contact closure to IP interface

INSTALLATION CHECKLIST

The following steps are a loose outline to install the software and connect the Flex-IO hardware:

1) Install Flex-IO Builder software.

This is the GUI program for the Flex-IO 16.

2) Install Flex Control Builder software.

This is required if you want to have access to the Control Libraries for Serial and IP

Devices within the Flex-IO Builder.

3) Connect Flex-IO 16 via Program Port to PC

It is recommended that you initially communicate with the Flex-IO through a Serial Cable

to its “Program Port”. It is easier to initially connect and configure the device via Serial

(rather than IP).

Figure 1 – Example of connecting the Flex-IO 16 to the serial cable and serial cable adapter

of the “FLEX-PRGM FLEX PROGRAM KIT”. (Power adapter is also shown.)

If you are trying to connect the Flex-IO via IP first, you will need enough understanding

and system privileges on the PC to change the PC’s “Local Area Connection” settings to

allow the PC to communicate with Flex-IO’s factory default IP settings (shown below):

IP address: 192.168.5.80

Subnet mask: 255.255.255.0

Gateway: 192.168.5.48

4) Verify the Firmware version and possible Upgrade of Firmware

5) Program, Download, and Test the various Actions required for the various Flex-IO

Channels.

Sample commands are shown below:

GPI 1 LOW

GPO 1 ON

WAIT 1000

SER ‘passed serial string <0D>’

IP 200.30.4.5:345 "ACTION = VPRESS DESKTOP 1 BUTTON 1<0D>"

IP 200.30.4.5:345 "<01 57 7F 03 4D 55 54 30 08 20 09 21 0A 20 10 21 1F 2C 02>"

SERIAL CONNECTION DETAILS

The Flex-IO Builder program has the serial control settings programmed in to communicate via

the “Program Port”.

If you would like to use your choice of terminal software (e.g. HyperTerminal, PuTTY, etc.) to

communicate with the Flex-IO hardware directly through the “Program Port”, these are the

serial settings:

Baud rate: 115200

Data bits: 8

Parity: None

Stop bits: 1

Handshake: None

The serial settings for the “Control Port” are potentially changed on each “Download Project”

based on the settings for the “Control Port” in the Project.

If no Project has been downloaded, the default serial settings of the “Control Port” are:

Baud rate: 115200

Data bits: 8

Parity: None

Stop bits: 1

Handshake: None

ETHERNET CONNECTION DETAILS

The Flex-IO Builder program has the Ethernet (or IP) control settings programmed in to

communicate via the “Ethernet Port” provided the IO 16’s IP Address is configured.

If you would like to use another program (such as TELNET) to communicate with the Flex-IO

over Ethernet, use Port 16001 (not 23).

When connecting to the IO16 via IP, the IO16 will terminate the session after 5 seconds of

inactivity. Inactivity is defined as no data of any kind, typically ASCII characters when typing at

a telnet terminal. (Each operation performed by the Flex-IO Builder program on the “Connect”

dialog opens a connection, sends commands, and closes the connection within 5 seconds.)

Indice

Altri manuali FSR Hardware per computer

FSR

FSR INDIE 300 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente