FujiE HM-618EB Manuale utente
DEHUMIDIFIER
HM-618EB & HM-620EB
Thank you for choosing this product.
Please read this instruction manual before using it.
INSTRUCTION MANUAL
- 1 -
PRODUCT INTRODUCTION
HM-618EB & HM-620EB dehumidifier is equipped with microcomputer that provides a low
noise, energy-saving, multiple functions, simple and efficient operation. It is suitable to use
mostly in indoor environment; office, living room, studio, laboratory etc. It can also be used
for drying clothes, protecting electronic equipment and high-end furniture from the humid
environment. DY-618EB gives you a pleasant living environment.
PERFORMANCE CHARACTERISTIC
1. Indoor humidity is regulated between RH 40%~90%.
2. Protection against tank-full, frostbite and delay start-up
compressor.
3. Indicator light for tank-full, operation, defrost and humidity.
4. Easy to pull out and washable filter.
5. Electronic humidity indicator which indicate ambient relative
humidity when it is operating.
PART NAME & OPERATING PRINCIPLE
Parts name:
- 2 -
Function of Dehumidifier
The function of dehumidifier:
1. When the dehumidifier is in operation, the fan draws indoor air to the cold cooling coils
and then over the warm condenser coils.
2. Indoor air will condense over the cooling coils which moisture will form.
3. The moisture on the coils will drip from the coils to the water tank.
4. The indoor dry air continues to flow through the warm condenser coils.
OPERATION INSTRUCTION
Operation panel:
- 3 -
Temperature switch reference
Open
1. Set the Humidity Setting (On/Off switch) to the off.
2. Connect the plug to the socket.
3. Set the Humidity Setting (On/Off switch) to the desired humidity rate, and it’ll start
to work and temperature will be monitored automatically.
Water tank
1. When the water tank is full, the indicator light will
show (compressor and fan will stop running).
2. Pull out the water tank and empty it.
3. Place it back into the unit. (as picture)
Continuous drainage (if continuous dehumidify
please continuous drainage as follows)
1. Pull out water tank
2. Remove rubber cap on the drainage outlet
at the back of unit (as picture)
3. Connect the drainage hose to the drainage
outlet at the back of the unit
4. Place water tank into the unit
5. Set the Humidity Setting (On/Off switch) to
the “Continue” and it starts to operate.
6. The diameter of drainage hose is 10 mm.
Turn off
1. Set the Humidity Setting (On/Off switch) to off.
2. Cut off the power if unit is not in use.
- 4 -
Notice
1. Dehumidifier unit will not run if the temperature setting is higher than the actual
temperature.
2. When the water-tank is full, compressor and fan will turn off automatically. Empty
the water tank in order to run it.
3. The compressor delay start-up for 3 minutes i.e. compressor will run after 3 minutes
of fan start-up
4. The compressor and the fan will turn off automatically when the indoor temperature
reaches the setting temperature.
5. When unit finished defrost, the compressor will turn off but the fan will run.
6. If the temperature sensor or humidity sensor is malfunction, the compressor and the
fan will turn off automatically; the operating light will show every two second.
TECHNICAL DATA
Model HM-618EB HM-620EB
Water Removal Capacity 18L/day (30℃RH80%) 20L/day (30℃RH80%)
Power Supply AC230V ～50Hz AC230V ～50Hz
Rated Power 330W 340W
Rated Current 1.6A 1.65A
Max Power 420W 440W
Max Current 2.0A 2.15A
Maximum Discharge Pressure 2.5Mpa 2.5Mpa
Maximum Suction Pressure 1.0Mpa 1.0Mpa
Refrigerant R134a/125g R134a/125g
Operating Range 5°C ～32°C 5°C ～32°C
Net Weight 13Kg 13Kg
- 5 -
IMPORTANT
- 6 -
IMPORTANT
- 7 -
IMPORTANT
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali FujiE Deumidificatore
