FULTON Rail Guide Coping Sled Pro Manuale utente
Version 1.0
Rail Guide Coping Sled PRO
Exploded View & Parts List
Clean, Square Cuts Everytime
Turn o Power Ear Protection Sharp
CAUTION Eye Protection Respiratory
Protection
Disconnect
saw from
power source
before tting
or removing
insert.
Always wear
proper eye
protection
when working
with machinery
and tools.
Always wear
proper ear
protection when
working with
machinery.
Always wear
proper respiratory
protection when
working near
airborne dust
particles.
Use caution when han-
dling sharp objects (saw
blades, router bits, drill
bits and so on). Use pro-
tective gloves whenever
possible.
Please read and fully understand
any and all safety materials that
came with your power tools or
machinery before operation. Always
follow all safety guidelines set in
place by the power tool or machine
manufacturer.
Safety First
5
2
1
3
10
11
9
8
6
4
7
No. Description
PARTS LIST - Coping Sled Pro
Clear Acrylic Fence Guide
Coping Sled Base
Fixed Fence
Adjustable Fence
Toggle Clamp
Sacricial Wood Backer Block
Post Handle Front
Post Handle Back
1”Threaded Round Knob
Black Bushing
1” x 5/16 tpi T-bolt
1
1
1
1
1
1
1
1
3
1
2
16
13
12
14
17
17
15
2½” x 5/16 tpi T-bolt
1¾” x 5/16 tpi T-bolt
1¾” x 24 tpi bolt
Capped Nut
Steel Washer
1¾”Wood Screws
2
2
4
4
4
2
Quantity
1
2
3
4
5
6
7
8
9
9
12
12
14
15
16
9
13
13
10
10
11
Basic Assembly
• Assemble the Rail Coping Sled Pro as shown in the exploded
drawing. Do not attach the Sacricial Wood Backer Block at
this time. This will be done once the calibration process is
complete. Once the sled is assembled, loosen the 1” round
knobs on top of the Clear Rail Guide as well as the rear Post
Knob Handle and the four cap nuts on the toggle.
Setup and Use
Calibrating The Sled
1. With the 1” round knobs loosened, place the Rail Coping
Sled Pro onto your router table with the Clear Acrylic Fence
Guide snuggly up against the router table fence.
2. Adjust the coping sled so that Coping Sled Base is exactly
3/4” away from the router table fence. This measurement
needs to be accurate, so be sure to measure at both ends
of the Coping Sled Base. Once you have both ends of the
base set at 3/4” away from the router table fence, make
sure the Clear Acrylic Fence Guide is against the router ta-
ble fence, rmly secure the 1” round knobs.
3. With the 4 cap nuts on the toggle and the rear post knob
loose, keep the Clear Acrylic Fence Guide against the rout-
er fence, use a square to set the Fixed Fence to 90° in ref-
erence to the Coping Sled Base. Once you have the Fixed
Fence set, rmly secure the rear Post Knob Handle.
4. Lay the Rail Coping Sled Pro on its side and secure the Tog-
gle to the Fixed Fence using the wrench provided and a
philips head screw driver (not included).
5. Double check that the Fixed Fence is still square to Coping
Sled Base.
Setting the Router Bit Height
6. Set a test piece of stock (must be same thickness as your
actual stock piece) on to the Sled Base (2). Following the
router bit manufacturers instructions, set the bit height.
7. Once you have the bit height set, secure the router bit to
lock it into position.
8. Adjust your router table fence so that the fence is ush
with the router bit’s bearing and secure the fence in place.
Following the router bit manufacturers instructions, set
the bit fence.
9. Once the router bit height is set, place the Coping Sled on
to the router table with the Clear Acrylic Guide at against
the router fence.
10. Place a test stock piece against the xed fence and slide
the end to be cut against the router table fence.
11. Move the adjustable fence so that it ts at against the
other side of the stock and secure the 1” knob on the ad-
justable fence.
12. Adjust the toggle foot assembly so that it rmly holds your
stock in place. Once the toggle is adjusted, engage the
toggle so that it is holding the stock down.
13. Make a test cut.
14. If necessary, repeat the router bit height setup process un-
til the stile and rail mate perfectly as shown below.
Please note that your Rail piece(s) should already be cut.
Rail
Rail
Style
Style
15. Once you are satised with your t, attach the Sacricial
Wood Backer Block as detailed in the following steps.
16. Place the Coping Sled back on to the router table with the
Clear Acrylic Fence Guide against the router table fence.
Set the Sacricial Wood Backer Block against the Fixed
Fence. Slide the end against the router table fence and se-
cure the Sacricial Wood Backer Block using the two sup-
plied wood screws that came with the coping sled.
Please note: When securing the Sacricial Wood Backer Block
against the Fixed fence, make sure it aligns with the
Clear Acrylic Fence.
17. Use a combination or engineer’s square to verify that the
Sacricial Wood Backer Block remained square to the rout-
er table fence.
18. Your Rail Guide Coping Sled Pro is now setup for your
rst cope cut. Secure your project project piece into the
sled and make your cuts!
Shop Tip
To accomodate dierent router bit proles, you will need to
make your own replacement Sacricial Wood Backer Block.
Do not throw away the old block, this can be used again for
future projects.
Altri manuali FULTON Accessori per utensili elettrici
