Furuno GP-1850DF Manuale utente

INSTALLATION MANUAL

COLOR DGPS/PLOTTER/SOUNDER

GP-1850DF

COLOR GPS/PLOTTER/SOUNDER

GP-1850F

Safety Instructions for the Installer .......................i

Equipment Lists .....................................................ii

System Configuration ...........................................iv

1. Installation of Standard Equipment ...............1-1

1.1 Installation of Display Unit ..............................................1-1

1.2 Installation ofAntenna Unit .............................................1-3

1.3 Installation of Transducers ...............................................1-4

1.4 Installation of Sensors ....................................................1-14

2. Wiring ...............................................................2-1

3. Initial Settings..................................................3-1

3.1 NMEA Setting ..................................................................3-1

3.2 Output Data Sentences .....................................................3-3

3.3 Antenna Height.................................................................3-4

3.4 Baud Rate Setting (GP-1850DF only)..............................3-4

3.5 Beacon frequency Setting (GP-1850DF only) .................3-5

3.6 Depth Adjustment.............................................................3-6

3.7 External Equipment Setup (Option) .................................3-7

3.8 Selecting the Echo Sounder Output Power ....................3-10

4. Installation of DGPS Beacon Receiver

(for GP-1850F) .................................................4-1

APPENDIX TRIDUCER 525ST-PWC/PWD .......AP-1

PACKING LIST .................................................... A-1

OUTLINE DRAWINGS......................................... D-1

INTERCONNECTION DIAGRAM ........................ S-1

SCHEMATIC DIAGRAM ...................................... S-2

9-52, Ashihara-cho,

Nishinomiya, Japan

Telephone: 0798-65-2111

Telefax: 0798-65-4200

Your Local Agent/Dealer

All ri

hts reserved.

PUB. No. IME-43950-J

GP-1850F/1850DF

(

HIMA

)

FIRST EDITION : FEB. 1999

J : NOV. 01, 2001

Printed in Japan

iiiiiiiiiiiii

Ground the equipment to

prevent electrical shock

and mutual interference.

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or equipment damage. The

voltage rating appears on the label at the

rear of the display unit.

Use the correct fuse.

Use of a wrong fuse can cause fire or

equipment damage.

Keep the following compass safe

distance.

Standard Steering

Display Unit 0.98 m 0.74 m

CAUTION

When handling the transducer cable,

keep in mind the following points.

•Keep the cable away from oil and

fuel.

•Keep the cable away from the

place where it may be damaged

during the installation.

•Do not paint the cable.

The sheath of the transducer cable is

made of chlorophrene rubber (or vinyl

chloride). Therefore, do not paint the

sheath with organic liquid (such as

toluene) since it may harm the sheath.

WARNING

Do not work inside the

equipment unless totally

familiar with electrical

circuits.

Hazardous voltage which can

shock, burn or cause serious

injury exists inside the equip-

ment.

Turn off the power at the

mains switchboard before

beginning the installation.

Post a sign near the switch

to indicate it should not be

turned on while the equip-

ment is being installed.

Fire, electrical shock or

serious injury can result if the

power is left on or is applied

while the equipment is being

installed.

SAFETY INSTRUCTIONS

Safety Instructions for the Installer

Equipment Lists

Standard supply

.oNemaNepyT.oNedoCytQskrameR

1tinuyalpsiD E-F0581-PG-1F0581-PGrof

E-FD0581-PG- FD0581-PGrof

2tinuannetnA

710-APG-

F0581-PGrof

810-APG- FD0581-PGrof

910-APG- FD0581-PGrof

3recudsnarT

DSP5-025521-510-000

1.enotceles,tuptuoW006rofDWP5-025621-510-000

DSM5-025721-510-000

4straperapS10520-41PS062-573-4001esuF

5slairetamnoitallatsnI00250-41PC694-140-0001 .yssaelbaC,elbacrewoP

6seirosseccA 10420-41PF072-573-4001revocdraH

20420-41PF051-673-4001 ,lebalkramtuptuo,swercS noihsucrebbur

Optional equipment

.ONemaNepyT.oNedoCskrameR

1reviecernocaeBtik

810-A01-0581-208-RG894-140-000 pihw,A0007-RG,810-APG annetna

810-N01-0581-208-RG405-140-000A0007-RG,810-APG

S810-A51-0581-209-RG994-140-000 pihw,A0007-RG,S810-APG annetna

S810-N51-0581-208-RG505-140-000A0007-RG,810-APG

910-N01-0581-208-PG846-140-000A0007-RG,910-APG

S910-N51-0581-209-RG946-140-000A0007-RG,S910-APG

2elbacannetnA .yssa 51-D3-SP-CNT076-331-000 elbacannetnarof,m51 noisnetxe

3elbacannetnA tes

00710-02PC011-273-400 elbacannetnarof,m03 noisnetxe

01710-02PC021-273-400 elbacannetnarof,m05 noisnetxe

4.yssAelbaC050-3000FPS7A-JM10-037-631-000

5tnuomtsaM erutxif 1110-02PC087-563-400

6elgna-thgiR esabannetna 033AQ-31.oN932-308-000

tinuannetnagnitnuomrof7 annetnaelgna-L esab 013AQ-31.oN042-308-000

8esabannetnA gnitnuomliarrof 0615CR-31.oN411-608-000

iii

Optional equipment (con't)

.oNemaNepyT.oNedoCskrameR

9tinuannetnA

S810-APG264-140-000FD0581-PGrof

610-APG635-140-000F0581-PGrof

S910-APG455-140-000FD0581-PGrof

01recudsnarT

DSP5-025521-510-000W006rof

DWP5-025621-510-000W006rof,tnuoosnartelbac8/w

DSM5-025721-510-000 ,rotcennocfoorpretawdnaelbac8/w W006rof

T1-002/05071-510-000Wk1rof

11yssaelbaC2904S20484-431-000noitcennocrecudsnartWk1rof

21xobgnihctaM0001-BM908-040-000noitcennocrecudsnartWk1rof

31rosnesTS BSM20-TS689-731-000epytlluh-urhT

BSP20-TS789-731-000epytlluh-urht,elbac8/w

41StiklluhrennI033AQ-31.oN042-308-000tinuannetnagnitnuorof

51 erutarepeT rosnes

BTM20-T620-040-000

BSM20-T040-040-000

BSM30-T720-040-000

61recudirT

DSM-TS425422-510-000 W006rof

DSM-TS525362-510-000

DWP-TS025821-510-000 W006rof

DWP-TS525162-510-000

71 retrevnoC noitcennoc 7414S20280-141-000

81reifitceR26-RP

484-310-000CAV001rof

584-310-000CAV011rof

684-310-000CAV022rof

784-310-000CAV032rof

91.yssaelbaC

050-1100FPS6A-JM442-231-0005,P4-P6,radarnoitcennocrof

001-1100FPS6A-JM633-231-00001,P4-P6,radarnoitcennocrof

050-2100FPS6A-JM424-431-0005,P6-P6,S/Erodiavanrof

001-2100FPS6A-JM718-331-00001,P6-P6,S/Erodiavanrof

02annetnapihW2.1-WAF640-631-000FD0581-PGrof

12 etoeR rellortnoc E-F581-CMR023-573-400yrettab,revoclyniv,rellortnoC

22draCMAR400-CM20MAR00097-173-400BM2

32 nocaeBSPGD revieceR 08-RG-F0581-PGrof

System Configuration

The GP-1850F/1850DF mainly consists of a display unit, a GPS antenna and a

dual frequency transducer.ADGPS beacon receiver is provided inside the display

unit for GP-1850DF type. The mini chart card drive in the display unit loads elec-

tronic charts. External equipment which can be connected include water tempera-

ture and speed sensors, autopilot, and DGPS beacon receiver (GP-1850F).

Ship’s mains

10.8—31.2 VDC

External equipment

(Autopilot, etc.)

DGPS beacon receiver

GP-1850F only

Transducer

Temp. sensor

(option)

ANTENNA UNIT

Receives signal from

GPS satellite and beacon

reference station

(GP-1850DF only).

DISPLAY UNIT

Ship’s position is

calculated in longitude

and latitude from signal

received from the an-

tenna unit and displayed

on the screen.

GPA-017

(for GP-1850F)

GPA-018

(for GP-1850DF)

1.2 m Whip antenna

(Option)

*Matching

Box

MB-1000

*Required for 1 kW transducer only

GPA-019

(for GP-1850DF)

1-1

1. Installation of Standard Equipment

1.1 Installation of Display Unit

Mounting considerations

The display unit can be installed on a tabletop, on the overhead or flush mounted

in a console or panel.

OverheadTabletopHard Cover

Figure 1-1 Tabletop, overhead mounting methods

When selecting a mounting location for the display unit keep the following in mind:

• Keep the display unit out of direct sunlight.

• The temperature and humidity should be moderate and stable.

• Locate the unit away from exhaust pipes and vents.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Keep the unit away electromagnetic field generating equipment such as motor,

generator.

• For maintenance and checking purposes, leave sufficient space at the sides

and rear of the unit and leave slack in cables.

• A magnetic compass will be affected if placed too close to the display unit.

Observe the following compass safe distances to prevent disturbance to the

magnetic compass:

Standard compass: 0.98 meters

Steering compass: 0.74 meters

• Rubber cushions which absorb vibration (supplied) may be attached as below

if vibration is a problem.

45±5mm

Aline with edge

of hanger.

Rubber cushion

TM-166 No.18 black

1-2

Mounting procedure

Follow the procedure below to mount the display unit on a tabletop or the over-

head.

Tabletop, overhead mounting

1. Fix the hanger by four tapping screws M5 X 16.

2. Screw knob bolts in display unit, set it to hanger, and tighten knob bolts.

3. Attach hard cover to protect LCD.

WARNING

Figure 1-2 Tabletop, overhead mounting of display unit

Flush mounting

Note:

Use supplied pan head screws when the thickness of the bulkhead is from

11 to 14 mm. For bulkhead which exceeds 14 mm in thickness the length of the

pan head screws should be bulkhead thickness plus 7.3±1.5 mm. Also the length

of B below should max. 7 mm.

1. Prepare a cutout in the mounting location whose dimensions are as shown in

Figure 1-3.

2. Fix the display unit by six pan head screws. Refer to the outline drawing on

page D-2.

1-3

Flush mount

Pan head screws

Cutout for flush mount

242 0.5

89 0.5

147 0.5

6-R2.25

244 1

143 1

15 0.5 238 1

Figure 1-3 Flush mounting of display unit

1.2 Installation of Antenna Unit

Mounting considerations

Install the antenna unit referring to the installation diagram on page D-3 or D-4.

When selecting a mounting location for the antenna unit, keep in mind the follow-

ing points:

• Select a location out of the radar beam. The radar beam will obstruct or prevent

reception of the GPS satellite signal.

• The location should be well away from a VHF antenna.AGPS receiver is inter-

fered by a harmonic wave of a VHF antenna.

• There should be no interfering object within the line-of-sight to the satellites.

Objects within line-of-sight to a satellite, for example, a mast, may block recep-

tion or prolong acquisition time.

• Mount the antenna unit as high as possible. Mounting the antenna unit as high

as possible keeps it free of interfering objects and water spray, which can inter-

rupt reception of GPS satellite signal if the water freezes.

• The length of the whip antenna for the GP-1850DF should be no longer than

1.2 meter to prevent antenna damage. Do not use a 2.5 meter whip antenna.

• If the antenna cable is to be passed through a hole which is not large enough to

pass the connector, you may unfasten the connector with a needle nose pliers

and 3/8-inch open-end wrench. Refasten it as shown in Figure 1-4 after run-

ning the cable through the hole.

Center pin (soldered)

Clamp nut

Connector shell

Gasket (reddish brown)

Washer Shield

Figure 1-4 How to assemble the connector

1-4

1.3 Installation of Transducers

Installing the inside-hull mount transducer

Necessary tools

You will need the following tools:

• Sandpaper (#100)

• Silicone sealant

Remarks on installation

• Do the installation with the boat hauled out of the water.

• Turn off the engine while installing the equipment.

• Install the transducer in the engine room.

Selecting the mounting location

Keep the following points in mind when selecting a mounting location:

• The mounting location should be where the hull is of single-hull thickness and

is void of air or flotation materials other than solid fiberglass between the trans-

ducer face and the water.

• Do not place the transducer over hull struts or ribes which run under the hull.

• Avoid a location where the rising angle of the hull exceeds 15°, to minimize the

effect of the boat’s rolling.

• You will finalize the mounting location through some trial and error. The proce-

dure for this is shown later.

50cm

15cm

1/3

1/2

Mounting location

for transducer

Center line

Figure 1-5 Inside-hull transducer mounting location

Altri manuali per GP-1850DF

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Furuno Plotter

Furuno

Furuno Auto Plotter ARP15 Manuale utente

Furuno

Furuno GP-1871F Manuale utente

Furuno

Furuno GP-1871F Manuale utente

Furuno

Furuno FRS-1000A Manuale utente

Furuno

Furuno GP-3500 Manuale utente

Furuno

Furuno GP-1600F Manuale utente

Furuno

Furuno GP-1810F Manuale

Furuno

Furuno GD-188 Manuale utente

Furuno

Furuno RP-25 Manuale utente

Furuno

Furuno NavNet TZtouch TZTL9BB Manuale di istruzioni

Furuno

Furuno GPS Plotter GP1600 Manuale utente

Furuno

Furuno GP-3500 Manuale

Furuno

Furuno RP-250 Manuale utente

Furuno

Furuno GP-3500 Manuale

Furuno

Furuno RP-180 Manuale utente

Furuno

Furuno GP-1670 Manuale utente

Furuno

Furuno LP-1000 Manuale utente

Furuno

Furuno 1932 MK2 Manuale utente

Furuno

Furuno GP-1810 Manuale utente

Furuno

Furuno RP-340 Manuale utente

Furuno

Furuno GP-1670F Manuale utente

Furuno

Furuno GP-3100 Mark-2 Manuale utente

Furuno

Furuno Auto Plotter ARP15 Manuale utente

Furuno

Furuno RP-17 Manuale utente

Manuali Plotter popolari di altre marche

MUTOH

MUTOH Kona 760 Manuale utente

HP 7475a Manuale utente

Vulcan-Hart

Vulcan-Hart FC-500VC Manuale utente

Roland

Roland TrueVIS VG-640 Manuale del proprietario

Roland

Roland VersaCamm SP-540V Manuale utente

MIMAKI

MIMAKI CF2 Series Manuale utente

Ioline

Ioline Summit Manuale utente

Summa

Summa S CLASS Manuale utente

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuale utente

HP 7470A Manuale utente

SII

SII LP-1010 Manuale utente

Great Computer

Great Computer JII-61 Manuale utente

Roland

Roland VersaUv LEF - 12i Manuale utente

Lectra

Lectra Alys 120 Manuale utente

MUTOH

MUTOH Ultima SC-850D Manuale utente

Skycut

Skycut D Series Manuale utente

Commodore

Commodore 1520 Manuale utente

Esko

Esko Kongsberg XE Manuale utente