Fusion MS-RA60 Manuale utente

Fusion®MS-RA60 Installation Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in personal injury, damage to the vessel, or poor

product performance.

See the Important Safety and Product Information guide in the product box for product warnings and other

important information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install this product.

Before applying power to this product, make sure it has been correctly grounded, following the instructions in

the guide.

CAUTION

To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling,

cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.

You must read all installation instructions before beginning the installation. If you experience difficulty during

the installation, contact Fusion Product Support.

What's In the Box

• Mounting gasket

• Four 6-gauge, self-tapping screws

• Two screw covers

• Power and speaker wiring harness

• Auxiliary-in, line-out, and subwoofer-out wiring harness

Tools Needed

• Phillips screwdriver

• Electric drill

• Drill bit (size varies based on surface material and screws used)

• Rotary cutting tool or jigsaw

• Silicone-based marine sealant (optional)

GUID-3453BF25-825C-403E-917D-EF24C7294A81 v1March 2021

Mounting Considerations

• You must mount the stereo on a flat surface that provides open airflow around the rear of the stereo for heat

ventilation.

• If you are installing the stereo in a location that may be exposed to water, you must mount it within 45

degrees of the horizontal plane.

• If you are installing the stereo in a location that may be exposed to water, add a drip loop to the cable to

allow water to drip off of the cable and avoid damage to the stereo.

• If you need to mount the stereo outside a boat, you must mount it in a location far above the waterline, where

it is not submerged, and where it cannot be damaged by docks, pilings, or other pieces of equipment.

• To avoid interference with a magnetic compass, you must install the stereo at least 15 cm (5.9 in.) away

from a compass.

2 Fusion MS-RA60 Installation Instructions

Mounting the Stereo

NOTICE

Do not use the stereo as a template when drilling the mounting holes because this may damage the display and

void the warranty. You must only use the included template to correctly drill the mounting holes.

Be careful when cutting the hole to mount the stereo. There is only a small amount of clearance between the

case and the mounting holes, and cutting the hole too large could compromise the stability of the stereo after it

is mounted.

Do not apply grease or lubricant to the screws when fastening the stereo to the mounting surface. Grease or

other lubricants can cause damage to the stereo housing.

Before you can mount the stereo in a new location on the mounting surface, you must select a location in

accordance with the mounting considerations.

1Adhere the template to the mounting surface.

2Drill a hole inside the corner of the dashed line on the template.

3Cut the mounting surface along the inside of the dashed line on the template.

4Ensure the mounting holes on the stereo line up with the pilot holes on the template.

5Using an appropriately sized drill bit for the mounting surface and screw type, drill the pilot holes.

6Remove the template from the mounting surface.

7Complete an action:

• If you are installing the stereo in a dry location, place the included mounting gasket on the back of the

stereo.

• If you are installing the stereo in a location that is exposed to water, apply silicone-based marine sealant

on the mounting surface around the cutout.

NOTICE

Do not install the included mounting gasket if you applied sealant to the mounting surface. Using sealant

and the mounting gasket may reduce water resistance.

8If you will not have access to the back of the stereo after installation, make the necessary wiring

connections.

9Secure the stereo to the mounting surface using the included screws .

You should hand-tighten the screws when securing the stereo to the mounting surface to avoid over

tightening them.

10 Snap the screw covers in place .

Connections

The stereo must be connected to power, to speakers, and to media input sources to function correctly. You

should carefully plan the layout of the stereo, speakers, and your input sources before making any connections.

Fusion MS-RA60 Installation Instructions 3

Port Identification

Item Description

FUSE Contains the 15 A fuse for the device.

Not used.

Connects the stereo to the auxiliary in and zone 1 line/subwoofer out wiring harness.

Connects the stereo to a typical AM/FM antenna using a Motorola type antenna connector.

If you are installing the stereo on a boat with a metal hull, you must use a ground-dependent antenna,

and if you are installing the stereo on a boat with a non-metal hull, you must use a ground-independent

antenna. See the installation instructions provided with your antenna for more information.

Connects the stereo to the power and speaker wiring harness.

4 Fusion MS-RA60 Installation Instructions

Wiring Harness Wire and Connector Identification

Wire Function Wire Color/

Number Notes

Power (+) Red Connects to the positive terminal of a 12 Vdc power source

capable of supplying 15 A.

Ground (-) Black

Connects to the negative terminal of a 12 Vdc power source

capable of supplying 15 A. This wire should be connected before

connecting the red wire. All accessories connected to the stereo

must share a common ground location.

Amplifier on Blue Connects to an optional external amplifier to turn it on when the

stereo turns on.

Dim Orange

Connects to the boat's illumination wire to dim the stereo screen

when the lights are on.

The gauge of the illumination wire must be suitable for the fuse

supplying the circuit it is connected to.

Speaker zone 1 left (+) White

Speaker zone 1 left (-) White/black

Speaker zone 1 right (+) Gray

Speaker zone 1 right (-) Gray/black

Speaker zone 2 left (+) Green

Speaker zone 2 left (-) Green/black

Speaker zone 2 right (+) Purple

Speaker zone 2 right (-) Purple/black

Auxiliary in left

Auxiliary in right

Provides a red and white RCA stereo line input for audio sources,

such as a CD or MP3 player.

Zone 1 line out left

Zone 1 line out right

Provides a full-range output to an external amplifier, and is asso

ciated with the volume control for zone 1.

Subwoofer out

Provides a single mono output to a powered subwoofer or

subwoofer amplifier.

A connected subwoofer is associated with the volume control for

zone 1.

Fusion MS-RA60 Installation Instructions 5

Connecting to Power

When connecting the stereo to power, you should connect it through a circuit breaker rated for 15 A.

If it is necessary to extend the power and ground wires, use 14 AWG (2.08 mm2) wire. For extensions longer

than 1 m (3 ft.), use 12 AWG (3.31 mm2) wire.

1Route the red power wire to a circuit breaker rated for 15 A , and route the black ground wire to the

battery.

2If necessary, route a wire between the circuit breaker and the battery .

3Route the wiring-harness plug to the stereo.

Do not connect the wiring harness to the stereo until after all of the bare wire connections have been made.

4Connect the black wire to the negative (-) battery terminal.

5Connect the red power wire to the circuit breaker, and connect the circuit breaker to the positive (+) battery

terminal.

6Connect the wiring harness plug to the stereo.

Speaker Zones

You can group speakers in one area into speaker zones. This enables you to control the audio level of the

zones individually. For example, you could make the audio quieter in the cabin and louder on deck.

One pair of 4 Ohm speakers can be connected per zone.

Zones 1 and 2 are powered by the on-board amplifier. To use the RCA line output and the RCA subwoofer

output (associated with zone 1), you must connect an external amplifier.

You can set the balance, volume limit, tone, and name for each zone. You can set the subwoofer level for zone

Single-Zone System Wiring Example

Speakers

Water-tight connection

6 Fusion MS-RA60 Installation Instructions

Complete System Wiring

This diagram illustrates a system installation with an external amplifier and subwoofer connected to the stereo

using a line out. You can connect an amplifier and subwoofer only to zone 1 on the stereo.

NOTE: You can also connect speakers to the speaker wires for the internal stereo amplifier while using an

external amplifier connected to the line out. Adjusting the volume affects speakers connected to the internal

amplifier and speakers connected to the line out. This may result in uneven volume levels.

Item Description

Zone 2 speakers

Water-tight connection

Zone 1 speakers

Amplifier-on signal wire

Powered amplifier

Zone 1 line out and zone 1 subwoofer out

Zone 1 subwoofer

Fusion MS-RA60 Installation Instructions 7

Stereo Information

Specifications

General

Weight 316g (11.2 oz)

Water resistance IEC 60529 IPX7 (front), IEC 60529 IPX5 (rear)1

Operating temperature range From 0 to 50°C (from 32 to 122°F)

Storage temperature range From -20 to 70°C (from -4 to 158°F)

Input voltage From 10.8 to 16 Vdc

Current (max.) 15 A

Current (muted) less than 190 mA

ANT® wireless range Up to 3 m (10 ft.)

Compass-safe distance 15 cm (5.9 in.)

Fuse 15 A mini-blade type

Bluetooth® wireless range Up to 10 m (30 ft.)

Wireless frequencies/protocols Bluetooth 2.4 Ghz at 12 dBm maximum ANT 2.4 GHz @ 7 dBm maximum

On-board, Class D Amplifier

Output power per channel 4 x 22 W RMS at 14.4 Vdc input, 4 Ohm, 10% THD2

Total output music power 4 x 45 W max. 4 Ohm. 180 W max.

Line output level (max.) 5.5 V (peak to peak)

Aux input level (typical) 1 V RMS

Tuner Europe and Australasia USA Japan

FM radio frequency range 87.5 to 108 MHz 87.5 to 107.9 MHz 76 to 95 MHz

FM frequency step 50 kHz 200 kHz 50 kHz

AM radio frequency range 522 to 1620 kHz 530 to 1710 kHz 522 to 1620 kHz

AM frequency step 9 kHz 10 kHz 9 kHz

1 From the front, the device withstands immersion in water of up to 1 m for up to 30 m. From the rear, the device withstands light jets of water (up to 30 kPa

(4.4 psi) at distance of 3 meters) for up to 3 min.

2 The stereo may limit the output power to prevent the amplifier from overheating, and to maintain the audio dynamics.

8 Fusion MS-RA60 Installation Instructions

Stereo Dimension Drawings

Front Dimensions

157 mm (6 3/16in.)

68 mm (2 11/16in.)

Side Dimensions

22 mm (7/8in.)

81.2 mm ( 33/16 in.)

50 mm (2 in.)

Fusion MS-RA60 Installation Instructions 9

Top Dimensions

130 mm (5 1/8 in.)

22 mm (7/8 in.)

10 mm (3/8 in.)

Registering Your Fusion Device

Help us better support you by completing our online registration today.

• Go to www.fusionentertainment.com.

• Keep the original sales receipt, or a photocopy, in a safe place.

Software Updates

For best results, you should update the software in all Fusion devices at the time of installation to ensure

compatibility.

You can update the software using the Fusion-Link™ remote control app on your compatible Apple® or Android™

device. To download the app and update the device software, go to the Apple App StoreSM or the Google Play™

store.

Garmin®, the Garmin logo, ANT®, Fusion®, and the Fusion logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Connect IQ™,

Fusion-Link™, and Fusion-Link Lite™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

Apple®, the Apple logo, iPod touch®, and iPhone® are trademarks of Apple Inc., registered in the U.S. and other countries. App StoreSM is a service mark of Apple Inc.,

registered in the USA and other countries. Android™ and Google Play™ are trademarks of Google Inc. The trademark iPhone® is used in Japan with a license from

Aiphone K.K. Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. Other trademarks and trade

names are those of their respective owners.

A03942

Altri manuali per MS-RA60

Indice

Altri manuali Fusion Attrezzatura nautica