Future Automation PLH Manuale utente
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
Your Pack
Should Contain
1 PLH -
Plasma Lift Hinge
Mechanism
Suitable for
26" to 50"
screens
1 Standard PL
Fixtures Pack
The contents
of which can be
found on Sheet 17
1 IR
Remote Control
Sheet 1 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
WARNING
Mechanisms which lift
or move weights need
to be checked on a
yearly basis for any
damage which may
result in an accident
IMPORTANT
It is the responsiblity of
the installer to warn all
potential end users of
the dangers of interfering
with mechanisms during
operation
Stage 1
Check T
he O
peration O
f T
he M
echanism
OUT: Reveal Screen
IN: Hide Screen
STOP: Stops Mechanism
See SHEET 11 for further
controls
Connect the supplied IR
remote and check that the
mechanism operates
correctly before continuing
with the installation.
CONTROLS
Firstly, remove the
cable ties that keep the
mechanism safe and
secure during transit.
There are usually 6 ties
in various locations.
However, on some models
there may be more than
6 cable ties.
Once all the cable ties
have been removed, then
the mechanism can be
powered up and tested.
Sheet 2 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
Aluminum
Flap
6mm Flap
125
107
80
A
DETAIL A
SCALE 1 : 5
Remove mount and place base
central onto the beam into position
and reattach the mount.
Fix the base by using penny washers
and wood screws through the
base supports
provided as
shown in
De
tail A
Woodscrew
Penny
W
asher
Base
Base
S
upports
Stage 2
Fitting Flap And Base To Mechanism
FIXING
Make sure the base panel
lines up squarely, directly
on top of the lifting beam.
Consult
PLH TECHNICAL SHEET
before fabricating any
flaps or base panels.
The hole is necessary for hinge pole to pass through.
The 6mm flap and the base should be
made as part of the cabinet.
The surface of the flap should be
varnished or painted to prevent warping.
Take care when fixing the surfaces
together. Place the objects on a
flat surface to make sure the edges
are properly aligned when they
come into contact.
Try to use as many self
adhesive pads as possible
to get the most secure fixture.
VIEWING SIDE
Sheet 3 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
B
DETAIL B
SCALE 2 : 3
Stage 3
Fixing T
he L
ift In T
he C
abinet
Place the mechanism within the cabinet.
Raise the beam to the top and guide the
base carefully through the opening in the top.
With the base properly located, use the 8
pointed screws supplied, 4 on each side,
to pin the mechanism in place, fixing its
position left and right. These 8 screws
should be screwed through the middle
hole of each of the clusters of 3,
shown below right.
With the lift fixed in position, use 8 wood
screws on each side to secure the
lift to the cabinet.
Sheet 4 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
C
DETAIL C
SCALE 1 : 1
By adjusting the screw up
and down, you can adjust
the stop height of the beam,
and also the base panel.
Stage 4
Adjusting Base Panel Height
Sheet 5 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
C
DETAIL C
SCALE 1 : 3
Stage 5
Positioning The Base Panel
There should be a gap of about 3mm
around the edges of the base panel to
the cabinet.
See Stage 2 for instructions on fixing
the base.
CABLES
The cables for the screen
should pass up through
the pole up to behind
the plasma screen.
Sheet 6 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
1
2
3
Adjusting T
he F
lap-Up
P
osition
Stage 6
1
By adjusting the white screw,
at each side of the lift, you can
adjust the tilt of the flap.
By winding the push rods on each side, you can
adjust the height of the flap in order to get it level
with the cabinet top. Be sure to lock the nut securely
once adjusted. Make sure the black plate does not
touch the inside of the cabinet. This can cause
strain on the motor, leading to failure.
3
2
CABINET TOP - SIDE VIEW
By loosening the M6 bolts on each
side under the flap, you can adjust
the position of the flap in the hole
in the cabinet top. Aim for a
3mm gap all round.
CABINET TOP - PLAN VIEW
CABINET TOP - SIDE VIEW
Sheet 7 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
D
DETAIL D
SCALE 1 : 4
By adjusting the bolts under each flap arm as circled,
it is possible to alter the angle the flap opens to. It is
very important that when the flap is open, it rests
in a vertical position, as shown above.
Stage 7
Ch
ecking F
lap
D
own P
osition
Sheet 8 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift HingeMechanism
Technical Sheet
Carefully hook the screen with
the uprights properly secured
back onto the mounting frame
and position.
Stage 8
Fixing the screen to the lift
Simply mount the screen on to the mount supplied
with your mechanism. The example below
shows a Group A framework.
CABLES
When the screen is in the
home position, pass the cables
through
into the cabinet.
Once inside locate the cable
management system as circled
in the drawing. The cables can
be pushed inside to keep them
neat within the cab
inet
Place screen down carefully onto a
flat surface, remove uprights from
the mount and bolt onto the back of
the screen.
Sheet 9 of 17
ISSUE: 006
www.futureautomation.co.uk
FUTURE
AUTOMATION
PLH
Plasma Lift Hinge Mechanism
Instruction Sheet
Indice
Altri manuali Future Automation Supporto TV
Future Automation
Future Automation PS42 Manuale utente
Future Automation
Future Automation TTR60 Manuale utente
Future Automation
Future Automation PS65-M Manuale di istruzioni
Future Automation
Future Automation DA Manuale utente
Future Automation
Future Automation PS-VESA Series Manuale utente
Future Automation
Future Automation PS32-M Manuale utente
Future Automation
Future Automation PS42 Manuale utente
Future Automation
Future Automation PS Series Manuale utente
Future Automation
Future Automation PS60 Manuale utente
Future Automation
Future Automation PS55-M Manuale di istruzioni
