FW Murphy Centurion C5 M-VIEW MV-5-C Manuale utente

00-02-1031

2019-08-07

Section 50

Centurion™

M-VIEW™

MonochromeLCD(MV-5-C)

OperationsManual

BEFORE BEGINNING INSTALLATION OF THIS FW MURPHY PRODUCT:

Please read the following information before operating the Centurion

controller. This installation information is intended for Centurion controller

only.

Visually inspect the product for any damage during shipping.

Before proceeding please visit our website and review our support

documentation including Wiring the Murphy Way.

www.fwmurphy.com/uploaded/WIR_Murphy_Way.pdf

Disconnect all power and be sure machine is inoperative before beginning

installation.

Installation is to be done only by a qualified technician of the Responsible

Body.

Observe all Warnings and Cautions at each section in these instructions.

Device shall be wired in accordance with NEC, CEC or other local code, as

applicable.

Please contact FW Murphy immediately if you have any questions.

For Class I, Division 2:

This equipment is an open-type device and is meant to be installed in an

enclosure suitable for the environment such that the equipment is only

accessible with the use of a tool.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.

Warning –Explosion Hazard –Do not disconnect equipment unless power has

been removed or the area is known to be non-hazardous.

Warning –Explosion Hazard –Do not replace batteries unless the area is

known to be free of ignitable concentrations.

For AEx/Ex Zone 2:

The equipment shall only be used in an area of pollution degree 2, as defined in IEC 60664-1.

The equipment shall be installed completely within an enclosure that provides a minimum

ingress protection of IP 54 in accordance with UL 60079-0 and only accessible by the use of a

tool.

Transient protection shall be provided that is set at a level not exceeding 140% of the peak

rated voltage value at the supply terminals to the equipment. This protection is supplied

internal to the equipment. No additional protection is required.

The wire size, torque rating of 12-24 AWG, 0.37-0.44 ft.-lbs. and suitable supply wire

temperature rating of 96ºC minimum shall be provided for the input power terminal block.

THIS PAGE INTENTIONALLY LEFT BLANK

 
 
Table of Contents 
Introduction....................................................................................................................................................................1 
Product Description...................................................................................................................................1 
Led Indicators ...........................................................................................................................................1 
MV-5-C Display Features .............................................................................................................................................4 
Home Screen /Landing Page....................................................................................................................4 
Navigation Keys........................................................................................................................................5 
Reading the Screen..................................................................................................................................7 
Maneuvering in Edit Mode........................................................................................................................8 
Status and Mode of the Controller............................................................................................................9 
FN Screen.................................................................................................................................................9 
Password......................................................................................................................................................................10 
Passwords and Screen Access ..............................................................................................................10 
Before Starting the Equipment for the First Time.................................................................................................11 
Setup –MV-5-C Display.........................................................................................................................11 
Operational Screens...................................................................................................................................................14 
User-Configurable Screens ....................................................................................................................14 
Map of Operational Screens...................................................................................................................14 
FW Murphy Logo Screen........................................................................................................................14 
Corporate and Configuration Information Screen...................................................................................15 
Bootloader and Firmware Information Screen........................................................................................15 
Digital Input Status Screen .....................................................................................................................15 
Temp Input Status Screen......................................................................................................................16 
Shutdown History Screen .......................................................................................................................16 
Shutdown Snapshot Screen ...................................................................................................................16 
Event History Screen..............................................................................................................................17 
Active Alarm Screen ...............................................................................................................................17 
Gage Display Screen..............................................................................................................................18 
Line-by-Line Screen................................................................................................................................18 
Custom Control Loop Screen .................................................................................................................18 
Rod Load Screen....................................................................................................................................19 
Setup Screens and Menus.........................................................................................................................................20 
Setpoints Setup Screen..........................................................................................................................21 
General Timer Setup Screen..................................................................................................................22 

 
 
State Timer Setup Screen ......................................................................................................................23 
Maintenance Timer Setup Screen ..........................................................................................................23 
Control Loop Setup Screen ....................................................................................................................24 
Miscellaneous Setup Screen ..................................................................................................................27 
Digital Input Setup Screen......................................................................................................................28 
Pulse Input Status Screen ......................................................................................................................28 
Digital Output Setup Screen ...................................................................................................................29 
Analog Inputs Setup Screen...................................................................................................................30 
Analog Outputs Setup Screen ................................................................................................................31 
Temperature Inputs Setup Screen..........................................................................................................32 
Rod load Setup Screen...........................................................................................................................33 
Display Board Status Screen..................................................................................................................34 
MVIEW Communication Status Screen..................................................................................................35 
Centurion Communication Status Screen ..............................................................................................36 
Real Time Clock Setup Screen...............................................................................................................36 
Super User Menu Screen (Super User Password Protected)................................................................37 
Centurion Serial Ports Screen (Super User Password Protected).........................................................38 
Centurion CAN Ports Screen (Super User Password Protected)...........................................................38 
Centurion Ethernet Screen (Super User Password Protected)..............................................................39 
Centurion EMMC Log Files Screen (Super User Password Protected).................................................39 
MVIEW Serial Ports Screen (Super User Password Protected) ............................................................40 
MVIEW CAN Ports Screen (Super User Password Protected)..............................................................40 
MVIEW Ethernet Screen (Super User Password Protected) .................................................................41 
MVIEW Static Block Screen (Super User Password Protected) ............................................................41 
Communications.........................................................................................................................................................42 
Display Communication Ports.................................................................................................................42 
Downloading Configurations and Firmware Updates.............................................................................42 
Replacement Parts and Assemblies........................................................................................................................43 
Accessories..................................................................................................................................................................43 
Centurion Configuration Tool Software ..................................................................................................43 
Glossary........................................................................................................................................................................43 
 
 

Section 50 00-02-1031

2019-08-07 - 1 -

Introduction

Product Description

The Centurion configurable controller is a display and controller combination expressly designed to meet the

requirements of three specific kinds of applications:

Screw Compressors

Reciprocating Compressors

Pumps

The heart of the Centurion system is the main input/output (I/O) module or controller, which can be mounted on a

standard DIN rail. While it is designed to work with any Modbus (Master) compliant HMI (Human Machine

Interface) or with no operator interface at all, it is optimally configured and field-configurable using the Centurion

Configuration Tool, powerful software developed to configure the controller. Parameters can be modified in the

field without special need for laptop or software by utilizing FW Murphy’s specially programmed M-VIEW

controller display.

The controller is designed to monitor, control, protect and optimize small-to medium-sized gas operated

compressors and pumps in the field. Proper operation is maintained by monitoring setpoints and digital, analog

and temperature input points and providing the logic to take corrective and/or proactive steps.

The controller also allows for controlled shutdown and no-flow monitoring as well as auto start up and engine

control capabilities.

The controller provides real-time data via communications ports to a connected display and/or supervisory

system. This advanced system offers multiple options for remote communications and operation. The industry

standard Modbus RTU or Modbus TCP/IP protocol means greater support for a wide variety of communication

equipment including radio and satellite communications systems.

Led Indicators

MV-5-C Display –Front Side

Please be aware of the following conditions and the resulting LED appearances:

If the unit has an invalid application or needs to sync (M-VIEW Replacement only), the Red LED is

Off and the Amber LED will Flash.

When the bootloader exits to run the application, the Red and Amber LEDs are turned Off.

Section 50 00-02-1031

2019-08-07 - 2 -

MV-5-C Display –Back Side

The LEDs are located next to the serial port connections.

All Ports RX/TX LEDs include:

The serial activity LEDs blink with every transmitted or received message.

oThe RX LED blinks Red when a packet is received by the display.

oThe TX LED blinks Green when a packet is transmitted by the display.

C5-1 Controller

NOTE: The Expansion modules have the same 2 Power LEDs and COP blink codes as

the C5-1. They are located next to the power plug on all modules.

C5-1 Power LED Indicators –Power is always two green LEDs

2 Green LEDs:

2 on - Unit is powered normally

1 on - Internal power failure. Needs service

Off - No DC power to unit

C5-1 COP LED Indicators –Controller Operating Properly

Green LED:

1 Blink/sec - Unit is running application normally

Fast blink - Bootloader mode

3 Blinks - Missing configuration

4 Blinks - Running in recovery mode

Off - Controller not operating

Section 50 00-02-1031

2019-08-07 - 3 -

C5-1 Digital Input LED Indicators –Digital Inputs

Green LED:

On - Input active (DC+ or -)

Off - Input active (open)

C5-1 Digital Output LED Indicators –Relay Outputs, FET DC+, FET DC-

Green LED:

On - Output on

Off - Output off

C5-1 Communication LED Indicators - RS232, RS485, CAN bus

RED LED:

Flash - Unit is transmitting data to device

Off - No communication active

GREEN LED:

Flash - Unit is receiving data

Off - No communication active

RS232

RS485

CAN bus

C5-1 DIP Switch Setting

Switch 1-8: Modbus Slave Address function for RS485-2 / RS232-2

Selectable 1-253

If set to address 0, RS485-2 and RS232-2 ports default to 9600 baud.

Set to address 1 to connect to the controller if settings are not known. This is the

default setting from the factory.

Switch 9: Set to ON to enable CAN1 line termination if C5-1 is at the end of the CAN bus

network.

Switch 10: Set to ON to enable CAN2 line termination if C5-1 is at the end of the CAN bus network

Section 50 00-02-1031

2019-08-07 - 4 -

Display Features

The display module is a highly integrated operator interface specially programmed to complement and support the

Centurion controller. The primary purpose of the display is to:

view controller operational information

view/edit controller operational parameters

send commands to controller, such as stop, edit and reset

Home Screen / Landing Page

Your default Home Screen / Landing Page is determined by the first page configured in the Centurion

configuration, and may look similar to this example.

Indice

Altri manuali FW Murphy Monitor

FW Murphy

FW Murphy AFR-64R Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione