G21 Razor Manuale utente

HU PL

RAZOR

HAND

DRYER

Do not attempt to install the unit yourself unless you are a trained service technician. Otherwise,

this may affect the safety and proper functioning of the unit.

Read this manual thoroughly and carefully before beginning to use the unit, ensuring safety and

proper function. Please keep it well for later reference.

Features

Drying hands without contact is hygienic.

Electricity cost saving because of drying hands at high speed.

Do not use towels and tissues, no dispose of waste.

Anti-bacteria and environmental materials, no pollution.

Thanks to heater switch is possible to set the cool or warm drying temperature:

• Heating switch to 1 (on), means the heating is always on, ambient temperature can not effect

the heating.

• Heating switch to 0 (on), means the heating is automatic working, this means:

»When the ambient temperature is below 20°C, the heating is on working, the hand dryer can

bring the warm air to the user.

»When the ambient temperature is over 20°C, the heating is not working, the hand dryer only

bring the cool wind.

Anti-damage timer

Installed anti-damaged timer, this machine will stop work after working 25 seconds. Draw out your

hands and put again your hands into the dryer to continue use.

No need windpipe.

Separate air supply, quite

hygienic.

No drip comes into the unit.

Upper and lower air

nozzles.

Prevent water drops form

splattering on the unit body.

Ergonomic shapes, for

comfortable use.

Ease of use.

A. Airﬂow

B. Drain tank

C. Air inlet

Thank you for purchasing our product.

Before using this unit, please read this manual in order to avoid improper handling and use

ofthedevice.

Warning

Personal injury accidents will happen if use improperly.

• Do not open the front panel, otherwise, this may get an electric shock.

• Children forbidden hanging on the machine, there is risk of falling.

• Do not use in a wet environment, for example, near the bathroom where it may get the direct

water and places where the condensation may form, otherwise, this may cause electric shock and

unit malfunction.

• Do not allow the unit get wet, otherwise it will cause electric shock.

• Do not modify and disassemble the unit unnecessarily. Otherwise, this may cause a ﬁre, electric

shock, or personal injury.

• If power tolerance is over +/-10%, there will be breakdown. If using incorrect power supply, ﬁre,

electric shock and machine malfunction will happen.

• Please use dedicated socket. If using together with other appliances, the socket may cause

abnormal heat leading to ﬁre.

• Power must be cut off when maintenance to prevent the risk of electric shock.

• Drain tank and air ﬁlter must be installed. Do not switch on after power connected for 10 seconds.

• If the machine doesn’t work or have abnormal conditions, please cut off power to prevent

accidents and close leakage circuit breaker and ask supplier to check and repair, or it may lead to

ﬁre because of electricity leakage and short circuit.

• It must have the reliable grounding wire otherwise it may cause electric shock when the unit

failure or leakage.

• Attention when installation: do not install when the machine are power connected.

• It must be operated by the professional construction person, who was trained examined the

knowledge requirements of the standards relating to electrical equipment (paragraph 50) when

install the unit. If the construction is incorrect, it may cause electric shock and ﬁre accident.

• This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

• If the cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁed persons in order to avoid a hazard.

Packing list

Unit 1 pc

Mounting plate 1 pc

5 mm expansion pipe 6 pcs

5x30 mm self-tapping screw 6 pcs

User manual 1 pc

Part names and dimensions

1. Heat switch

2. Speed governor

3. Power switch

4. Dreainage line

5. Water tank

6. Filter

7. Terminal box location

8. Installation panel

9. Power cord hose (rear)

10.Installation base

Using the unit

Stretch out both hands

and insert them all the way

in. The unit starts to run

automatically.

Pull them out slowly, letting

the air blow the water off.

Pull them out completely.

Self-check indicator

When a malfunction or error occurs, the self-check indicator on the right side will either light up

or ﬂash.

Turn off the power switch, wait about 40 seconds until all the indicators go off, then turn on the

power switch.

If the indicator still lights up or ﬂashes, turn of the power, disconnect the unit from the socket, and

contact your dealer immediately.

When using the unit

Turn on the power switch.

The power indicator lights up.

The lamp lights up.

The cover of power supply is closed.

Cleaning the unit body

Clean the unit with a soft cloth. If the unit gets very dirty, clean with a soft cloth dampened with

neutral agent, then clean with a dry soft cloth.

Remove the dirt from the sensor (to prevent malfunction).

Note

Only use the neutral cleaning agents.

Do not use thinner, accidic or alkaline toilet cleaners, or nylon brush. (Otherwise, they may damage

the smoothness of surface).

Only use alcohol to clean the hans drying area. (Do not use alcohol anywhere else).

If the chemical cloths used, please read their instructions ﬁrst.

Disinfecting agents will damage your unit.

Warning

Before you clean the unit, turn off the power switch.

Do not splatter water on the unit.

Caution

Wear gloves when cleaning.

The antibacterial coating becomes not effective when the surfaces get very dirty.

A B

Draining and cleaning the drain tank

Before it ﬁlls up (at least once a week).

• The water blown off the hands is called ‘’drain water’’.

• Empty the drain water at any moment, in order to prevent accumulated water from exceeding the full level.

• It will start smelling if the accumulated water remains in the tank for too long time.

Pull the drain tank out in the horizontal direction.

This ensures the drain water does not splatter out.

Open the cover and empty the water.

Pull the cover up with your ﬁn-

gers in the direction of the arrow

on top of the cover and then re-

move the cover completely.

Wash out the interior of the

drain tank.

A. Full level

B. Drain tank

C. Cover

Close the water tank cover

and re-attach it to the unit as

original.

Open the side panel, wipe with a cloth.

Regular cleaning drainage routes, can effectively inhibit bacteria.

Cleaning the air ﬁlter

Around once a week.

Remove the air ﬁlter. Cleaning the air ﬁlter.

If it is very dirty, wash it off with cold or warm water.

Re-attach to the unit.

Insert it all the way in, until it stops. If it is not in place, the dirt or dust will enter to the unit and

shorten its service life.

Note:

If you wash the air ﬁlter with water, dry it as much as possible. Do not expose to the ﬁre.

Beat it lightly by hand or use a

vacuum cleaner.

Pull the air ﬁlter out.

Trouble shooting

If you discover the following circumstances, please inspection and handling as following:

Problem Check Action

No air blows

when hands are

inserted.

Do the display indicators lights up?

Is the power switch on?

Are you putting your hands all the

way in?

Check the ground-fault circuit

breaker.

Turn the power switch on.

Reput hands all the way in.

Machine works

long time after

hands drawn

out, ﬁnally stop.

Any dirt or foreign body on sensor? Switch off the power button and

then remove dirt or foreign body on

sensor after the power light off, when

ﬁnished, switch on power button.

No hot wind. There is a built-in heater in the unit.

Any dirt on heating sensor?

Fuse inside terminal box blown?

Is the ambient temperature higher

than 20°C?

Switch off power, remove front cover.

There is a terminal box inside. Take

down the cover of terminal box.

Check the fuse inside box which is

blown or not.

Airﬂow is too

low.

Is the speed button on low level? Put speed button on high level.

If the above actions do not work, turn off the power and the ground-fault circuit breaker and

call your dealer to inspect and repair it if necessary.

Electrical circuit chematic

910

14 15

3 4 5 6

1. Power

2. Power switch

3. Heat switch

4. Fuse protector

5. Thermal fuse

6. PTC Electric heater thermostat

7. Hand dryer control circuit

8. Fuse protector

9. Capacitor

Status Status Solution

Power

indicator

light

Light

Power

input

normally

Extinguish

Power not supply.

Check the external

power source, close the

power switch.

Master board fuse

blew out.

State

indicator

light

Extinguish Don’t

work Flashing

light

Motor fault,

it can’t start

normally.

Check motor connecting

wires and the rotor

foreign material.

Always

light Working

Trick or working

time longer than

25s.

Clear work space foreign

material, restart to work.

10.Transformer

11.Sensorless BLDC motor

12.Sensorless brushless DC motor

13.Infrared receiver control circuit

14.Speed potentiometer

15.Infrared emission

16.Operating instuctions

17.Power indicator

Precautions before installing

Do not install in the following types of location, otherwise this may cause malfunction:

• Locations where the temperature can exceed -10 C or 40 C.

• Locations where the unit may come into direct contact with water.

• Locations where the unit is under direct or strong sunlight.

• Locations where there is a lot of condensation.

• Locations where corrosive, neutral, or reductive gases are present.

• Places lower than -20m or hig her than 2000m above sea level.

Installation location:

• Install the unit somewhere, where it will be easy to use, as shown in the ﬁgure. If the unit is in-

stalled too low, water may get on it when the ﬂoor is being cleaned. (The bottom of the unit must

be at least 150 mm higher than the ﬂoor or any objects under it.)

• The left side of the unit must be at least 150 mm away from any walls, because the power switch

is located on the left.

• Ensure there are no mirrors or walls near the right side, as drops of water may splatter to the

right when drying hands. (Recommended distance is at least 100 mm.)

• Avoid locations where people or doors might bump into the unit.

• Choose a completely ﬂat surface on the wall to install the unit.

Installation base:

• If your space is limited and the condition of wall is unsatisfactory, you can purchase an installa-

tion base to install the unit.

1. Fixing screw

2. The mounting screw holes

3. Machine hanging hole

4. Wall screw into position

Indice

Lingue:

Altri manuali G21 Asciugatrice

G21

G21 RAPID Manuale utente

Manuali Asciugatrice popolari di altre marche

Bosch

Bosch WTA79200GB Manuale utente

Amana

Amana W10233410A Manuale utente

Miele

Miele TWH 780 WP Manuale utente

Asko

Asko T760 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manuale utente

Bosch

Bosch Logixx 10 WTB76556GB Scheda tecnica

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manuale di istruzioni

Electrolux

Electrolux EW2H328R2 Manuale utente

Beko

Beko DS8433RX1M Manuale utente

Dawlance

Dawlance Spinner DS 6000 C Manuale utente

Electrolux

Electrolux TP5080TW Manuale utente

AEG

AEG TR838P4OB Manuale utente

Indesit

Indesit IDV 75 Manuale utente

Infiniton

Infiniton SD-DG85C Manuale utente

BOMANN

BOMANN WT 5019 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manuale utente

Asko

Asko T793C Manuale utente

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manuale utente