1 0 (OFF)
3 1 (ON) 0 (OFF)
5 0 (OFF) 1 (ON)
7 1 (ON) 1 (ON)
0 (OFF)
ADR0 ADR1
Address Link Positions
9600-0492. AC24/4 Alarms Controller Installation Instructions, Issue 1.2.1x1 12th December 2013. © G4S
Technology 2013. G4S Technology Limited cannot be held liable for technical and editorial omissions or errors
made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of
this material. All trademarks acknowledged.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference. In which case, the user will be required to correct the interference at his
own expense.
ADR0 (LK2)
Position 1
(ON)
ADR1 (LK3)
Position 0
(OFF)
Note: For information on mounting the alarms controller into the
cabinet, refer to the appropriate cabinet installation instructions.
Specifications
Monitor points: 24 max.
Auxiliary outputs: 4 max.
Quiescent supply input: 75mA @12Vdc (no relays
energized).
Maximum supply input: 195mA @12Vdc (all relays
energized). Each relay consumes 30mA when energized.
Operating Range: 14 to 131°F (-10 to 55°C) max.
Humidity 15 to 90% non-condensing; indoor use only.
Compliance: EN50133, 1999/5/EC, UL 294 Access
Control & UL1076 Proprietary Burglar Alarm Systems.
M2150 AC24/4 Alarms Controller Installation Instructions
Addressing
1
Set the address of the controller using the links shown below. When connected to a DBU, the controller can be set to address
1, 3, 5 or 7. When connected to a 2DBC or 4DBC, the controller must be set to address 3, 5 or 7. When connected to an
8DBC, the controller must be set to address 5 or 7. An alarms controller occupies two addresses (e.g. 5 and 6).
The AC24/4 alarms controller is a remote alarms control unit for M2150
security management systems. The controller enables direct
connection of up to 24 monitor points (for alarms monitoring) and 4
auxiliary outputs, and can be sited up to 3000ft (1km) from the
controlling M2150 DBU, 2DBC, 4DBC or 8DBC database unit (some of
these database units are available only in selected countries).
Alarms Controller
Replacement Parts:
Use only replacement parts provided by the manufacturer:
F1, P/N R-0811-1000
Note:
·For additional information regarding the installation, configuration
and proper use of this product:
SMS User Guide, P/N 9600-0429
M2150 Access Control Design Guide, P/N 9600-0420
M2150 Intrusion Guide, P/N 9600-0540.
M2150 UL1076 Compliance Manual, P/N 9600-0449.
·Some devices described in these instructions may not be
applicable for sites requiring UL compliance. Please refer to the
Access Control Design Guide for details of the controllers, modules
and features that have been UL tested for use with this device.
Additional Information
3
UL Compliance Notes:
1). For UL1076 Proprietary Burglar Alarm Systems and Non-Stand Alone UL294 Access Control System (central monitoring
employed) installations, Altronix AL400ULX power supply must be used for system battery supervision function.
2). When using Altronix AL400ULX power supply, the installer will need to provide a remote input to the AC24/4 to monitor AC
power loss and battery supervision conditions as indicated below:
Altronix AL400ULX
Power Supply
I/O Board at
DB/DBU Location
+
+
-
-
+
-
Black
Black
Black
Red
7000-0126
Battery
Monitoring
Relay
12 VDC Out
+-
AC Fail
Monitoring
Relay
Monitor
Point 1
Monitor
Point 2
Cabinet
AC Power /
Tamper Board
NC
NC
NO
NO
C
C
12 VDC to power Local
boards & devices
Program Monitor Point 1 as 3
State N.C., and program the
Monitor Point Message to read
“AC Power Fail, (Add Board
Description)”
Program Monitor Point 2 as 3
State N.C., and Alarm Message
should read “Battery Trouble,
(Add Board Description)”
3). For UL294 Stand-Alone Installations, the MN-TRANS-75-UL and MN-PSU-KIT-MKII can be employed.
10K Ohm
10K Ohm
