galant 6160EX Manuale utente
6160EX Keypad
User Instructions
2
Contents
Glossary.....................................................................................3
Introduction ...............................................................................4
Day Mode, Full Setting and Unsetting.....................................5
Part And Night Setting..............................................................7
Cancelling Alarms.....................................................................8
Resetting After an Alarm ..........................................................8
Viewing the event log................................................................9
Omitting Zones From the System. .........................................10
Chime .......................................................................................11
Setting the Time and Date ......................................................11
Adding and Removing Keyfobs. ............................................12
Adding and Removing Keytags.............................................12
Adding and Changing User Codes ........................................13
User Descriptors......................................................................14
Testing the System..................................................................15
System Indications..................................................................16
Keypad Tones..........................................................................16
Hotkeys ....................................................................................17
Additional Information ............................................................17
Zone Information.....................................................................18
3
Glossary
The following terms will be used in this manual:
Alarm: A panel detection circuit has been tripped.
Cancel: The action of stopping an alarm condition.
Keyfob: A remote control device for setting and unsetting. Each
fob will belong to a user.
Keytag: A tag or card which can be used for setting and
unsetting. Each tag will belong to a user.
Keypad: The user interface device that displays system
conditions and allows user control.
Reset: The action of clearing the alarm or fault condition and
restoring the system to the steady state condition.
Tamper: A fault condition on a detector or system module.
User: Any person who accesses the system. This system can
have up to 8 users (number 1 to 8).
User Code: A 4 digit code used to identify a particular user to the
system.
Zone: A unique detection circuit to which a detector is
connected. There are also 'internal' system zones which
monitor the health of the system.
4
Introduction
Your Galant panel has various system functions, which can be accessed
by one of three methods:
• type a user code at a keypad
• press a button on an RF keyfob or
• present a keytag to a proximity reader.
The system can support up to 8 users. User 1 is assigned as the master
user. Each user can have a user code (master user code is 1234 by
default) and either a fob or a tag. Your installer will indicate which
methods are available on your system.
The following diagram shows an RF keyfob:
The following diagram shows a proximity card reader and keytag
1. Unset/Cancel
2. Begin Full Set procedure
3. Begin Part Set procedure
4. Begin Night Set procedure
Keytag presented to
proximity reader to set
and/or unset system.
keytag
5
Day Mode, Full Setting and Unsetting
Day mode is the normal mode for the system. In
this state the display will be similar to that
shown on the right, with the time and date.
Full Setting the System
To full set the system (keypad)
1. Type your User Code.
2. Press 1 (FULL)
A constant exit tone will sound.
The exit tone will become broken as the user
passes detectors on the exit route. The exit tone
will become constant, when the last detector on
the exit route has been passed.
Two confirmation beeps indicate that the system
has set and the screen will go Blank.
Note: To abort the setting procedure during the
exit time, press the * key.
To full set the system (keyfob)
Press the ON button on the keyfob. Full setting will commence as in
point 2 for keypad setting.
Note: To abort the setting procedure during the exit time, press the
OFF button.
To full set the system (keytag)
Keytags can be used to full set the system and to unset from any set
state.
Hold keytag in front of LED’s for 3 seconds. Full setting will
commence as in point 2 for keypad setting.
Note: To abort the setting procedure during the exit time, hold keytag
briefly in front of LED’s.
Galant V2
21-01-02 09:54
FULL SETTING
Exit Now
Open Zn:02
Exit Now
6
Unsetting the System from any Set State
To unset the system (keypad)
1. Proceed to the keypad via the approved
route. A pulsed tone will indicate that the
entry timer is counting down.
2. Type in your User Code at the keypad
before the expiry of the entry time. The
tones will stop and the keypad will return to
the Day Mode display.
To unset the system (keyfob)
Press the OFF button on the keyfob. The system unsets with a double
beep.
To unset the System (keytag)
Hold card briefly in front of keypad LED’s. The system unsets with a
double beep.
Note: If no response is obtained after 3 seconds, when presenting a
card, then the card is not recognized by the system. If a triple
beep is heard after holding the card, there is a fault on the
system. Refer to keypad display for details.
Unsetting from Part or Night Set
Unsetting from Part set and Night set conditions is identical to
unsetting from a Full set.
Galant V2
21-01-02 09:54
7
Part And Night Setting
It is possible to set the system but leave certain detectors switched off.
This is useful, for example, at night while the bedrooms are occupied,
or when leaving pets within the premises. Your installer can set up
these detectors.
To Part set the system, proceed exactly as for
Full setting except instead of pressing 1(Full):
Press 2 (PART) to Part set
OR
Press 3 (Night) to Night set
The keypad tones may be silenced during Part or
Night setting as agreed with your installer.
Two confirmation beeps indicate that the system
has set and the screen will go Blank.
Galant V2
21-01-02 09:54
PART SETTING
Exit Now
8
Cancelling Alarms
If an alarm activation is in progress, whether the
system is set or unset, proceed directly to the
keypad and type in your User Code. This will
cancel the alarm condition and the display will
show the source of the alarm. Typically, this will
be the detection zone that caused the alarm
condition.
Please see the table at the end of this manual for a full list of alarm and
fault condition displays.
If the system is set and in alarm, the alarm can be cancelled using a
keyfob or keytag, by unsetting in the normal manner.
Resetting After an Alarm
After an alarm has been cancelled and displayed, it must be reset. This
is typically done by typing your User Code again. The display will
return to the Day Mode display.
If the alarm message remains on the display, it may be that the alarm
condition has not been cleared. Check the source and type your User
Code again.
Installer Resets
Under certain conditions, it may not be possible to reset the alarm panel
by typing your User Code.
If you see this display, an installer reset is
required. Please contact your installer.
1. If you see this display, an ‘Anti-Code’ is
required from the monitoring station. Phone
the Station quoting the number on your
keypad display.
Intruder ZN:07
RF SUP. ZN:14
Call Engineer
Reset Required
Call Engineer
Quote 12345
9
Viewing the Event Log
The Galant alarm panel has an Event Log history that records every
event which occurs on the system. This includes setting, unsetting,
alarm activations and fault conditions. To view the event log:
1. Type in your User Code.
2. Press the # key then 0 (LOG).
3. The display will show the most recent event
on the system.
4. You can scroll backwards and forwards
through the log as follows:
Key 1= Scroll Back one event.
Key 3= Scroll Forwards one event.
Key 4= Scroll Backwards 10 events.
Key 6= Scroll Forwards 10 events.
Pressing the # Key at any point can show additional information, such
as zone description, on the bottom line of the display.
Pressing the * key escapes from the event log and returns to the Day
Mode display.
The event log display has the following format:
Time Date
Event type Event Source
(Alarm/set etc) (Zone or User)
09:54 21/4/03
Intruder Zone 06
08:30 10/01/03
Unset User 03
10
Omitting Zones From the System.
To allow flexibility, you can temporarily disable individual detection
zones. This is called ‘Omitting’. Once a zone is omitted, it will be
disabled for the duration of the next set period. When the panel is next
unset, the zone will be enabled again.
To Omit any zone:
1. Type in your User Code.
2. Press 6 (OMIT).
3. Type the zone number to be omitted. Each
zone number is a double digit (e.g. 03 or
14). The display will show the zone.
4. Repeat step 3 for any other zone if needed.
5. Press the * key to finish or wait 5 seconds.
The system can now be set in the normal way.
Clearing Omitted zones (Un-omit)
To un-omit zones and return to normal operation:
1. Type in your User Code.
2. Press 6 (OMIT).
3. Press the * key.
When you hear the two confirmation beeps, all zones will be re-
enabled.
Omitted ZN:03
Zone 3
Indice
