Gallagher SMB Demonstration Suitcase Manuale utente

Gallagher
SMB Demonstration Suitcase
User Guide
Gallagher SMB Demonstration Suitcase NZ/AU: C500900
Edition 1 | December 2021

Introduction
Thank you for choosing Gallagher SMB.
The Gallagher SMB Demonstration Suitcase has been specifically designed as a sales and
training tool to enable you to demonstrate the Gallagher SMB solution.
Contents
Check the suitcase contains the following items:
• 1 x SMB Controller (C500100)
• 1 x SMB HBUS 8In Board (C500680)
• 1 x SMB HBUS 8In 4Out Board (C500684)
• 1 x SMB Fire Relay & Fuse Board (C500993)
• 1 x Power Supply 3.5A (C200340)
• 1 x I/O Board Mounting Plate (C200001)
• 1 x Permaconn Kit (NZ C500609 or AU C500610)
• 1 x T15 Reader (C500481)
• 2 x SMB Key Tags (C500470/C500471)
• Switches to allow for simulation
Dimensions
The external dimensions of the suitcase are:
Length: 53 cm
Height: 42 cm
Width: 21 cm
Shipment weight: 9.7 kg
Compatibility
The Gallagher SMB Web Apps are compatible with Chrome, Safari, and Edge browsers.
The Gallagher SMB Mobile App is compatible with the following mobile phones:
• iPhone 7 or later, iOS 13.0 or later
• Android devices version 5.0 (Lollipop) or later and Chrome 70 or later

Configuration
The suitcase has the following factory configuration:
Door simulation
• Door Open:
Switch position 0 Door closed
Switch position I Door open
• Forced Door:
Switch position 0 Door lock is closed
Switch position I I Door lock is open
• Request to Exit:
Switch position 0 Door REX is closed (request to exit)
Switch position I Door REX is open (normal)
Inputs and outputs
The hardware within the suitcase is pre-wired to support a fictional site.
Input Connection
Input 9 Door Open Sensor
Input 10 Door Lock Sensor
Input 11 Door Request to Exit
Input 13 PIR
Input 14 Reed Switch
Input 15 Battery Low
Input 16 Mains Failure
Output 1 Door Unlock Relay
Output 2 Siren

Site
Use the image below to provide context when configuring and demonstrating the solution.
T15 Access Reader
STORE ROOM
AREA
OFFICE AREA
Roller Door Reed Switch
Office 3600PIR
User
You will be required to use your mobile phone to demonstrate the Customer App. You can
invite users to your fictional site, and allocate roles, so they can experience the product.
Name: John Smith
Role: Key Account Holder (Site Manager)
Privileges: Arm, disarm, lock/unlock doors, access all areas, receive incident notifications,
and manage users

Power on
Connect an IEC power cord (not supplied) from the 3.5 A Power Supply to an AC power outlet.
Switch ON. The controller and router will receive power.
You will need to perform a one-activation of the router. Once activated, ensure your location
has an adequate cellular signal.
Activate the router
1. Log into the Atlas Portal https://admin.permaconn.com/
2. Select the Fleet tab then Activate.
The 'Device Activation' screen displays.
3. Enter the PM54 serial number (located on the white label).
The 'PM 54v2 Activation' screen displays.
4. Complete the following fields:
Field Description
Usage Mode Select Router
Name Enter the site's Name
5. Select Next. The wizard navigates to the next screen.
6. Select Activate then OK.
The controller will automatically connect to the cloud via the
cellular router and come online.

Site creation
1. Log into the Gallagher SMB Configuration Web App:
https://app.halo.gallagher.com/installer/
2. Select New Site.
The 'New Site' lightbox displays.
3. Enter a name for the site. For example 'Sample Site - Demo'. Append the word 'Demo' to
the site name. Note: Demo sites will not be charged subscription fees. Gallagher will audit
the number of demo sites per partner.
4. Tick the 'Site uses tags' checkbox.
5. Complete the 'Key Account Holder' details, then select OK.
Field Description
First Name Enter John
Surname Enter Smith
Email Enter your Email
Phone Enter your Phone number. Check the country code to ensure the SMS two-
factor code is sent to your phone number.
When the site is activated, you will receive an email invite to the site, allowing
you to demo the Customer App using your phone.

Controller assignment
1. Select Scan controller QR code.
2. Capture an image of the controller's QR Code using your phone and present the image to
the laptop. The 'Physical ID' pop-up displays. Select OK to confirm the controller's ID.
The controller will download the latest firmware and update its default configuration.
3. Select the Controller.
The 'Controller 1' lightbox displays.
4. Disable the controller's front and rear tampers, then select OK.
Input and output configuration
1. Select Input 9.
Rename to "Door Open Sensor". Select OK.
2. Select Input 10.
Rename to "Door Lock Sensor". Select OK.
3. Select Input 11.
Rename to "Door Request to Exit". Select OK.
4. Select Input 13.
Rename to "Office PIR". Select OK.
5. Select Input 14.
Rename to "Roller Door Reed Switch". Change Sensor to Reed Switch. Change Alarm
Response to Secure Alarm. Select OK.
6. Select Output 1.
Rename to "Door Unlock Relay". Select OK.
7. Select Output 2.
Rename to "Siren". Change Output to Siren. Configure the Maximum On Time to 3
Minutes. Select OK.
8. Select the orange toggle to disable input 12 and inputs 1-8.
Note: During a demonstration it may be useful to explain that unused inputs should
always be "disabled". This helps speed up the installer testing of the system and ensures
inputs do not display "tampered" on the customer’s phone.

Area configuration
1. Select the AREAS tab, then select Area 1.
The 'Area 1' lightbox displays.
2. Rename to "Office".
3. Select Assign Outputs and select Siren as an Alarm Output.
The siren will activate when an alarm is triggered.
4. Select OK.
5. Select Add New. Select Area.
The 'New Area' lightbox displays.
6. Rename to "Store Room".
7. Select Roller Door Reed Switch.
8. Select Siren as an Alarm Output.
The siren will activate when an alarm is triggered.
9. Select OK.

Door configuration
1. Select the HARDWARE tab.
2. Select Add New. Select Door.
The 'New Door' lightbox displays.
3. Rename to "Office Door".
4. From the Open Sensor drop-down, select the "Door Open Sensor" input.
5. From the Lock Sensor drop-down, select the "Door Lock Sensor" input.
6. From the Area drop-down, select the "Office" area.
7. From the Request to Exit drop-down, select the "Door Request to Exit" input.
8. From the Lock Type drop-down, select "Mortise".
9. From the Reader drop-down, select "Reader 1".
10.From the Unlock Relay drop-down, select the "Door Unlock Relay" output.
11.Select OK.

Publish changes
Select Publish to publish your configuration to the controller.
Commission site
1. Select Commission site.
You will then be requested to complete the system tests, marking each item test result as
"Passed" before you can activate your site.
Note: This step in the installation process is where the technician will need to walk-test
the site to check wiring and configuration is all correct.
2. Before the site is activated the Commissioning Report can be viewed or downloaded as
required. This document can be provided to the Key Account Holder as evidence that the
site has been commissioned and is functioning correctly.
Activate site
Select Activate site.
Once the site is activated, the Key Account Holder (you) will receive an email invitation to
download the Customer App on your phone, to complete the registration. Open the email from
your phone and follow the instructions.
You should now be able to interact with your system using the Customer App on your phone.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Gallagher Controllori di accesso IP


















