Gardner Denver THOMAS SK927 Manuale utente

MODEL SK927

COMPRESSOR SERVICE KIT

CAUTION: Improper assembly or use of damaged parts may lead to

premature failure. To avoid frequent repairs follow these assembly

procedures.

NOTE: Before you begin read these instructions thoroughly. Assemble the

necessary tools. You will need a at tip and phillips head screw driver as well as a

T-20 and T-25 Torx driver for a torque wrench.

WARNING: Unplug the compressor before beginning disassembly.

ALWAYS NOTE POSITION AND ORIENTATION OF PARTS AS REMOVED

TO ASSURE CORRECT POSITIONING WHEN REASSEMBLING.

For service to 917/927 Series Compressors

FILTER REPLACEMENT

1. Remove lter cap.

2. Remove old lter and discard.

3. Wipe inside of lter body and cap with a clean soft cloth.

4. Place new lter inside of lter body.

5. Replace cap.

Filter Cap

Filter

Filter Body

621102 Valve Flapper

Intake & Exhaust (2)

633560 Gasket O-Ring

625223 Valve Plate

Screws (5)

625540 Diaphragm

Hold Down Screws (4)

625444 Head Screws

(6)

608212 Diaphragm

625160 Valve Flapper

Screws (2)

641034 Filter

617045 Valve Keeper

Strip (2)

3524 Washington Avenue, Sheboygan, WI 53081 USA

(920) 452-4891 www.gd-thomas.com

Hold Down Plate

Screw

Diaphragm

Connecting

Rod

Hold Down

Plate

DIAPHRAGM REPLACEMENT

1. Remove head.

2. Remove four screws from hold down plate. Discard screws.

3. Remove hold down plate, diaphragm and diaphragm liner (if present) from connecting

rod top. Wipe connecting rod top and hold down plate with a clean soft cloth.

4. Center new diaphragm and hold down plate over connecting rod holes. Make sure

all holes align as shown in the illustration below and that the diaphragm is centered

in the well of the housing. Insert four new screws. Torque screws to 20 in- lbs. in

criss-cross pattern.

5. Replace head and valve plate assembly. Torque screws to 40 in- lbs. in a criss-cross

pattern.

INTAKE & EXHAUST VALVE REPLACEMENT

1. Remove 4 head screws and head. Discard

screws. Turn head over. Remove 4 screws

from valve plate. Discard screws. Remove

valve plate from head. NOTE: If valve plate

needs to be pried out of head cavity, be careful

that the intake hole seat area does not get

damaged. If damage should occur the valve

plate will need to be replaced.

2. Remove and discard gasket.

3. Remove screw, apper and keeper from top

side of valve plate, discard. Wipe valve plate

and head with a soft clean cloth. Reassemble

new flapper and keeper with new screw.

Torque to 10 in- lbs. Make sure the end of

the apper covers the intake hole and that

the keeper is aligned properly. Turn valve

plate over and repeat procedure on exhaust

apper.

4. Wipe inside of head with a clean soft cloth, be

sure to remove any excess gasket. Install new

gasket.

5. Replace valve plate in head. (See Fig. #1).

Insert 4 new screws. Torque valve plate

screws to 40 in- lbs.

6. Replace head. Torque screws to 48 in- lbs. in

a criss-cross pattern.

Valve

Keeper

Valve

Flapper

Gasket

Valve Plate

Screw

Head

Altri manuali Gardner Denver compressore d'aria

Gardner Denver

Gardner Denver AUTO SENTRY EAU99G Manuale di servizio

Gardner Denver

Gardner Denver INTEGRA AIRSMART EFC99J Manuale di servizio

Gardner Denver

Gardner Denver INTEGRA EFA99F Manuale di servizio

Gardner Denver

Gardner Denver EBB BB-7.5 HP Manuale di servizio

Gardner Denver

Gardner Denver EnviroAire 15 Istruzioni per l'installazione

Gardner Denver

Gardner Denver AUTO SENTRY EAU99P Manuale di servizio

Gardner Denver

Gardner Denver L Series Guida alla risoluzione dei problemi

Gardner Denver

Gardner Denver L160 110A V2 Manuale utente

Gardner Denver

Gardner Denver ELECTRA-SCREW ESG Manuale utente

Gardner Denver

Gardner Denver APEX25-30B Manuale di servizio

Gardner Denver

Gardner Denver INTEGRA EFB99A Manuale di servizio

Gardner Denver

Gardner Denver EBM99M 60 Manuale di servizio

Gardner Denver

Gardner Denver SAVG2-75 Manuale di servizio

Gardner Denver

Gardner Denver TWISTAIR EWDQ D Manuale di servizio

Gardner Denver

Gardner Denver ELECTRA-SCREW EBE DD Series Manuale di servizio

Gardner Denver

Gardner Denver INTEGRA EFC99A Manuale di servizio

Gardner Denver

Gardner Denver ELECTRA-SAVER G2 Manuale di servizio

Gardner Denver

Gardner Denver VST55-90B Manuale di servizio

Gardner Denver

Gardner Denver VST225 Manuale di servizio

Gardner Denver

Gardner Denver Electra-Screw EDEQHF Manuale di servizio

Gardner Denver

Gardner Denver L Series Manuale utente

Gardner Denver

Gardner Denver L23 Manuale di servizio

Gardner Denver

Gardner Denver AirSmart EAU99T Manuale di servizio

Gardner Denver

Gardner Denver Thomas ULTRA AIR-PAC T-30HP Manuale

Manuali compressore d'aria popolari di altre marche

Sparmax

Sparmax DC-25XR Manuale utente

KAESER

KAESER M122 Manuale utente

GMC

GMC GAC1500 Manuale utente

Briggs & Stratton

Briggs & Stratton Air Compressor Manuale utente

Fini

Fini F3GST2TK Manuale utente

Industrial Air

Industrial Air CP1580325 Manuale di programmazione

Campbell Hausfeld

Campbell Hausfeld RP3300 Guida rapida

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuale utente

Hitachi

Hitachi EC99S Manuale dell'operatore

Parkside

Parkside PKO 270 A1 Manuale utente

Sullair

Sullair 185 Manuale utente

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuale utente

Ferm

Ferm CRM1046 Manuale utente

BE AC153 Manuale utente

RIDGID

RIDGID OF25150A Manuale utente

Johnson Controls

Johnson Controls QUANTUM LX Manuale

Sears

Sears Craftsman 919.167463 Manuale utente

Ring Automotive

Ring Automotive RAC700 Manuale utente