Garmin GLO 2 Manuale utente

August 2018 190-02468-91_0A Printed in Taiwan

GLO™2 GLONASS and GPS Sensor Instructions��2

Instructions pour le capteur GLONASS et GPS GLO™2 ��7

Istruzioni del sensore GLO™2 GLONASS e GPS��13

GLO™2-GLONASS- und GPS-Sensor – Anweisungen ��18

Instrucciones del sensor de GPS y GLONASS GLO™2 ��23

Instruções do GLO™2 GLONASS e do Sensor GPS��28

Instructies voor GLO™2 GLONASS en GPS-sensor ��33

Vejledning til GLO™2 GLONASS og GPS-sensor��38

GLO™2- GLONASS- ja GPS-antureiden ohjeet��42

Instruksjoner for GLO™2 GLONASS- og GPS-sensor��47

GLO™2 GLONASS- och GPS-sensorinstruktioner ��51

Instrukcja obsługi czujnika GLO™2 GLONASS i GPS ��56

Инструкция по эксплуатации датчика GLO™ 2 для систем ГЛОНАСС и GPS��61

GLO™2 GLONASS and

GPS Sensor Instructions

Installing the Battery



WARNING

This product contains a lithium-ion battery�

See page 5 for important battery safety

information�

1 With your thumbnail, slide the battery

cover release tab ➊�

➌➊

➋

2 Remove the battery cover ➋�

3 Locate the metal contacts on the end

of the lithium-ion battery�

4 Insert the battery ➌ so the metal

contacts on the battery align with

the metal contacts inside the battery

compartment�

5 Press the battery down into place�

6 Insert the battery cover into the

notches and press down�

The release tab locks the cover in

place�

Replacement Battery

You can purchase a replacement battery

(010-10840-00) at http://buy�garmin�com�

Charging the Battery

You can use the sensor while you are

charging it�

1 Plug the small end of the power cable

into the mini-USB connector on the

end of the sensor�

2 Plug the other end of the power cable

into an appropriate source of power for

the cable type�

It takes about three hours to charge the

battery� A fully charged battery lasts about

13 hours�

NOTE: If the battery has not been charged

for a long period of time, remove the

battery, connect the cable to the device

and a power source, and then replace the

battery� The battery will charge as usual�

Pairing the Sensor

1 Hold to turn on the sensor�

2 Turn on the other device and enable

the Bluetooth component�

You can refer to the device’s

documentation for specic instructions

about enabling Bluetooth wireless

technology�

3 Bring the sensor within 30 feet (10

meters) of the mobile device�

4 Using the mobile device, pair the

sensor with the mobile device�

The blue LED is solid blue when the

sensor is connected to the other device�

If the sensor has not established a

Bluetooth connection for several minutes,

it turns off automatically�

Bluetooth LED

LED Description

Slow ashing

blue

Searching for mobile devices

Rapid ashing

blue

Pairing

Solid blue Connected to mobile device

Status LED

LED Description

Slow ashing orange Charging

Solid orange Battery charged,

power connected�

Orange off Battery charged,

power disconnected�

Rapid ashing orange Low battery

Alternating orange

and green

Faulty battery or

system error

Flashing green Searching for GPS

satellites

Solid green GPS satellite x

Acquiring Satellite Signals

1 Verify that the blue LED on the sensor

is solid blue, indicating a wireless

connection�

2 Place the sensor where it has a clear

view of the sky�

Acquiring satellite signals may take a

few minutes. The Status LED ashes

green while searching for satellites and

establishing your location� The Status LED

is solid green when it has established a x

on your location�

Using the Portable Friction

Mount

The portable friction mount comes in

some GLO packages and is available as

an optional accessory�

1 Wipe the mounting surface and the

back of the mount with a wet cloth to

remove dust and debris�

2 Insert the sensor in the mount so the

LEDs face up and the mini-USB port is

accessible�

3 Place on a at surface.

Periodically, you should wipe the surface

and the mount with a wet cloth to remove

dust and debris to help prevent the mount

from sliding�

Registering the Device

• Go to garmin.com/express.

• Keep the original sales receipt, or a

photocopy, in a safe place�

Specications

Case: Rugged, but not water-resistant

Power Supply: Rechargeable lithium-ion

battery, 13 hours (typical use)

Update Rate: 10 Hz, but not all mobile

devices support a 10 Hz update rate�

Vehicle Power Cable* Input Voltage:

12–28 Vdc (*available in some packages)

Operating Temperature: -4°F to 140°F

(-20°C to 60°C)

Charging Temperature: 32°F to 113°F

(0°C to 45°C)

Short-Term (1 month) Storage

Temperature: -4°F to 122°F (-20°C to

50°C)

Long-Term (1 year) Storage

Temperature: -4°F to 68°F (-20°C to

20°C)

Important Safety and Product

Information



WARNING

Installation Warnings

When installing the device in a vehicle,

place the device securely so it does not

obstruct the driver’s view of the road ➊or

interfere with vehicle operating controls,

such as the steering wheel, foot pedals,

or transmission levers� Do not place

unsecured on the vehicle dashboard

➋� Do not place the device in front of or

above any airbag ➌�

➋

➌

➊

Battery Warnings

If these guidelines are not followed, the

battery may experience a shortened life

span or may present a risk of damage to

the sensor, re, chemical burn, electrolyte

leak, and/or injury�

• Do not leave the sensor exposed to a

heat source or in a high temperature

location, such as in the sun in an

unattended vehicle� To prevent the

possibility of damage, remove the

device from the vehicle or store it out

of direct sunlight, such as in the glove

box.

• Do not use a sharp object to remove

the battery�

• Do not disassemble, puncture,

incinerate, or damage the battery�

• Keep the battery away from children�

• If using an external battery charger,

only use the Garmin accessory

approved for your product�

• Only replace the battery with the

correct replacement battery� Using

another battery presents a risk of

re or explosion. To purchase a

replacement battery, see your Garmin

dealer or the Garmin website�

• When storing the device for an

extended time, store within the

following temperature range: from -4°F

to 68°F (-20°C to 20°C)�

• Do not operate the device outside of

the following temperature range: from

-4°F to 140°F (-20°C to 60°C)�

• Contact your local waste disposal

department to dispose of the device/

battery in accordance with applicable

local laws and regulations�

Navigation Warnings

Use this sensor only as a navigational aid�

Do not attempt to use the sensor for any

purpose requiring precise measurement

of direction, distance, location, or

topography� This product should not be

used to determine ground proximity for

aircraft navigation�

Product Environmental Programs

Information about Garmin’s product

recycling program and WEEE, RoHS,

REACH, and other compliance programs

can be found at www�garmin�com

/aboutGarmin/environment�

Declaration of Conformity

Hereby, Garmin declares that this product

is in compliance with the Directive

2014/53/EU. The full text of the EU

declaration of conformity is available at

the following internet address:

www�garmin�com/compliance�

FCC Compliance

This device complies with part 15 of the

FCC Rules� Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference,

and (2) this device must accept any

interference received, including

interference that may cause undesired

operation�

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to

part 15 of the FCC rules� These limits

are designed to provide reasonable

protection against harmful interference in

a residential installation� This equipment

generates, uses, and can radiate radio

frequency energy and may cause harmful

interference to radio communications if

not installed and used in accordance with

the instructions� However, there is no

guarantee that interference will not occur

in a particular installation� If this equipment

does cause harmful interference to radio

or television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one of the

following measures:

• Reorient or relocate the receiving

antenna�

• Increase the separation between the

equipment and the receiver�

• Connect the equipment into an outlet

that is on a different circuit from the

GPS unit�

• Consult the dealer or an experienced

radio/TV technician for help�

This product does not contain any user-

serviceable parts� Repairs should only be

made by an authorized service center�

Unauthorized repairs or modications

could result in permanent damage to the

equipment, and void your warranty and

your authority to operate this device under

Part 15 regulations�

Industry Canada Compliance

Category I radiocommunication devices

comply with Industry Canada Standard

RSS-210� Category II radiocommunication

devices comply with Industry Canada

Standard RSS-310� This device complies

with Industry Canada license-exempt RSS

standard(s)� Operation is subject to the

following two conditions: (1) this device

may not cause interference, and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device�

Limited Warranty

Garmin’s standard limited warranty applies

to this accessory� For more information,

go to www�garmin�com/support/warranty

�html�

Instructions pour le

capteur GLONASS et

GPS GLO™2

Mise en place de la batterie



AVERTISSEMENT

Ce produit contient une batterie lithium-

ion� Reportez-vous à la page 11 pour

consulter les informations importantes sur

la batterie�

1 Avec l'ongle du pouce, faites coulisser

le couvercle de la batterie ➊�

➌➊

➋

2 Retirez le couvercle de la batterie ➋�

3 Localisez les contacts métalliques à

l'extrémité de la batterie lithium-ion.

4 Insérez la batterie ➌de sorte que ses

contacts métalliques soient alignés sur

ceux gurant dans son compartiment.

5 Appuyez sur la batterie pour la mettre

en place�

6 Insérez le couvercle de la batterie

dans les encoches et appuyez�

La patte de dégagement garde le

couvercle bien en place�

Remplacement de la batterie

Vous pouvez acheter une batterie de

rechange (010-10840-00) sur http://buy

�garmin�com�

Chargement de la batterie

Vous pouvez continuer à utiliser le capteur

pendant le chargement�

1 Branchez la petite extrémité du câble

d'alimentation dans le connecteur

mini-USB à l'extrémité du capteur.

2 Branchez l'autre extrémité du

câble d'alimentation à une source

d'alimentation adaptée au type de

câble.

Le chargement de la batterie dure environ

trois heures� Une batterie entièrement

chargée a une autonomie d'environ

13 heures�

REMARQUE : si la batterie n'a pas été

chargée depuis longtemps, retirez la

batterie, branchez le câble à l'appareil et à

une source d'alimentation, puis replacer la

batterie� Le chargement de la batterie se

déroulera normalement�

Couplage du capteur

1 Maintenez la touche enfoncée pour

mettre le capteur sous tension�

2 Allumez l'autre appareil et activez la

fonction Bluetooth�

Reportez-vous à la documentation de

votre appareil pour savoir comment

procéder pour activer la technologie

sans l Bluetooth.

3 Eloignez le capteur à 10 mètres

(30 pieds) de l'appareil portable�

4 A l'aide de l'appareil portable, couplez

le capteur à l'appareil portable�

Le voyant bleu devient xe lorsque le

capteur est connecté à l'autre appareil�

Si le capteur ne parvient pas à établir la

connexion Bluetooth au bout de plusieurs

minutes, il s'éteint automatiquement�

Voyant Bluetooth

Voyant Description

Bleu - clignotement

lent

Recherche d'un

appareil portable

Bleu - clignotement

rapide

Couplage

Bleu - xe Connecté à un appareil

portable

Voyant DEL d'état

Voyant Description

Orange - clignotement

lent

Chargement

Orange - xe Batterie chargée,

branchée à

l'alimentation�

Orange - éteint Batterie chargée,

alimentation coupée�

Orange - clignotement

rapide

Batterie faible

Orange et vert -

alternés

Batterie défectueuse

ou erreur système

Vert - clignotement Recherche des

satellites GPS

Vert - xe Satellites GPS

localisés

Acquisition des signaux

satellites

1 Vériez que le voyant bleu du capteur

est xe, ce qui indique une connexion

sans l.

2 Placez le capteur à un endroit offrant

une vue dégagée sur le ciel�

L'acquisition de signaux satellites peut

prendre quelques minutes� Le voyant DEL

d'état vert clignote lors de la recherche

des satellites et de l'établissement de

votre position� Le voyant DEL d'état vert

est xe lorsque la connexion est établie

pour votre position�

Utilisation du support

portable antidérapant

Ce support portable antidérapant est

fourni avec certains appareils GLO et peut

être acheté séparément�

1 Nettoyez la surface de montage et

l'arrière du support avec un chiffon

humide pour éliminer la poussière et

les saletés�

2 Insérez le capteur dans le support : les

voyants doivent se trouver en haut et

le port mini-USB doit rester accessible�

3 Placez-le sur une surface plane�

Il est conseillé de nettoyer de temps en

temps la surface de montage et le support

à l'aide d'un chiffon humide pour éliminer

la poussière et les saletés et empêcher le

support de glisser�

Enregistrement de l'appareil

• Rendez-vous sur le site

garmin.com/express.

• Conservez en lieu sûr l'original de la

facture ou une photocopie�

Caractéristiques techniques

Boîtier : robuste, mais pas étanche

Alimentation : batterie lithium-ion

rechargeable, 13 heures (utilisation

standard)

Taux de mise à jour : 10 Hz, mais tous

les appareils ne prennent pas en charge

un taux de mise à jour de 10 Hz.

Tension d'entrée du câble allume-

cigare* : 12–28 V c�c� (*fourni avec

certains appareils)

Température de fonctionnement : de

-20 °C à 60 °C (-4 °F à 140 °F)

Température de chargement : de 0 °C à

45 °C (32 °F à 113 °F)

Température de stockage de courte

durée (1 mois) : de -20 °C à 50 °C (-4 °F

à 122 °F)

Température de stockage de longue

durée (1 an) : de -20 °C à 20 °C (-4 °F

à 68 °F)

Informations importantes sur

le produit et la sécurité



AVERTISSEMENT

Avertissements d'installation

Lors de l'installation de l'appareil sur un

véhicule, placez-le avec soin de telle sorte

qu'il n'obstrue pas le champ de vision du

conducteur ➊et qu'il ne gêne pas les

commandes du véhicule telles que le

volant, les pédales ou les leviers de

transmission� Ne posez pas le support sur

le tableau de bord ➋du véhicule sans le

xer. Ne placez pas l'appareil devant ou

au-dessus d'un airbag ➌�

Altri manuali per GLO 2

Indice

Lingue:

Altri manuali Garmin GPS

Garmin

Garmin nuvi 500-Series Manuale utente

Garmin

Garmin Mobile 10x Guida all'installazione

Garmin

Garmin Oregon 600 Manuale utente

Garmin

Garmin GPSMAP 527 Guide Manuale utente

Garmin

Garmin iQUE 3600 Manuale utente

Garmin

Garmin Cessna Caravan G1000 Manuale utente

Garmin

Garmin GPS 60 - Hiking GPS Receiver Manuale utente

Garmin

Garmin ECHOMAP ULTRA100 Series Manuale utente

Garmin

Garmin GTN 625 Manuale utente

Garmin

Garmin GPSMAP 695 Manuale utente

Garmin

Garmin Zumo 395 Manuale di istruzioni

Garmin

Garmin GPSMAP 3005C Manuale utente

Garmin

Garmin GPSMAP 4000 Series Manuale utente

Garmin

Garmin eTrex - Hiking GPS Receiver Manuale di istruzioni

Garmin

Garmin GVN 53 - Navigation System Guida di riferimento

Garmin

Garmin GNS 480 Manuale utente

Garmin

Garmin Astro DC 40 Manuale utente

Garmin

Garmin Alpha 100 Manuale utente

Garmin

Garmin GPSMAP 276C Guida di riferimento

Garmin

Garmin GHC 50 Manuale utente

Garmin

Garmin GPSMAP 192C Manuale del proprietario

Garmin

Garmin nuvi 200 Series Manuale utente

Garmin

Garmin nuvi 350 Manuale utente

Garmin

Garmin GPS II Istruzioni per l'installazione

Manuali GPS popolari di altre marche

Raven

Raven Cruizer II Manuale

Hama

Hama 53118 Manuale utente

Jigabot

Jigabot EX Manuale utente

Pointer

Pointer Cellocator CelloTrack XT LTE Guida all'installazione

Queclink

Queclink GV55LITE Manuale utente

Voxson

Voxson Voxtrack GPS500 Manuale di istruzioni

Starcom Systems

Starcom Systems Kylos Compact Manuale utente

Cobra

Cobra Marine MC 600Ci Manuale utente

Cellocator

Cellocator CelloTrack T Manuale utente

Enfora

Enfora Mini-MT GSM2228UG001 Manuale utente

Magellan

Magellan eXplorist 100 Manuale utente

LTE

LTE G50B Manuale utente

SkyGolf

SkyGolf SkyCaddie SG1 Manuale utente

Kenwood

Kenwood DNN9330BT Manuale utente

Safelet

Safelet Indra Manuale utente

Bushnell

Bushnell 360100 Manuale utente

Geneq

Geneq SXBlue Manuale utente

ORIGO

ORIGO ED308 Manuale utente