GATEXPERT GA1000AC Manuale utente
Sliding Gate Opener
User Manual
GA1000AC
Website: www.gatexpertstore.com
E-mail: sales@gatexpertstore.com
GA600AC Sliding Gate Opener User Manual
WARNING：
Always read this manual before installation, it contains important information
concerning installation, use, maintenance and safety.
Any operation not described in this manual is not permitted; incorrect use may damage
the product and even injure people and property.
Considering the possible dangers that may arise during the installation and use of the
gate opener, the installation must be carried out in strict compliance with building
construction standards and electrical operating procedures, in particular:
● Before starting the installation, check whether additional equipment or materials are
required to meet specific needs.
● Packaging materials must be handled in compliance with local regulations.
● Do not alter any parts except as described in this manual. Unexplained alterations may
cause malfunction. We are not responsible for any damage caused.
● Do not leak water or any liquid into the controller or other open devices. In such a case,
disconnect the power supply immediately. Continued use under such conditions is very
dangerous.
● When installing and positioning the motor, make sure that the power cord is unplugged
and the cover is removed before installing the motor on the mounting plate.
● The motor's operation involving electricity must be installed by a licensed professional.
● Do not install the product in an environment where there is an explosive atmosphere or
any risk of flooding.
● Use only original parts for all maintenance or repairs. If you use parts made by other
suppliers, we refuse to be responsible for the safety of the automatic control of this product.
● Do not modify the components of the control section of the product without the express
authorization of our company.
Keep this manual for future use.
GA600AC Sliding Gate Opener User Manual
CONTENTS
Default Setting Instruction..............................................................................................................1
Parts List...........................................................................................................................................2
Technical Parameters.....................................................................................................................4
Installation........................................................................................................................................4
Before You Start..........................................................................................................................4
Tools Required / Example Sliding Gate......................................................................................4
Step 1 - Gate Preparation...........................................................................................................5
Step 2 - Checking Manual Release.............................................................................................6
Step 3 - Removing / Installing Motor Cover.................................................................................6
Step 4 - Motor Pad Footing.........................................................................................................7
Step 5 - Fitting Mounting Plate and Motor...................................................................................8
Step 6 - Motor Position Adjustment.............................................................................................9
Step 7 - Gear Rack & Motor Alignment.......................................................................................9
Step 8 - Limit Switch Stops.......................................................................................................10
Step 9 - Powering on.................................................................................................................13
Step 10 - Testing Travel and Limit Stops...................................................................................14
Control Board.................................................................................................................................15
Programming and Wiring..........................................................................................................15
DIP Switch Adjustment..............................................................................................................16
Potentiometer Adjustment.........................................................................................................17
Terminal Instructions.................................................................................................................18
Wiring to the Terminal................................................................................................................19
Connecting Infrared Photocells.................................................................................................20
Remote Control Learning and Clearing.....................................................................................21
Maintenance...................................................................................................................................26
Troubleshooting.............................................................................................................................26
GA600AC Sliding Gate Opener User Manual
1
Then the gate will move in
the set direction.
Default Setting Instruction
The gate opener will open the gate to the right-hand side as its default setting. By default, the
opener mounts on the right-hand side. (Figure 1)
Figure 1
Gate in closed position Gate in open position
Before installation: Test the gate opener by plugging it into a power source and pressing the
remote. Press the opening button, the output gear rotates, then press the stop button, the output
gear stops rotating. Finally, press the closing button, the output gear rotates to the opposite
direction. This will give you an understanding of the way in which the opener will move the gate.
Figure 2
Note: Ensure that the gate opener is unplugged before proceeding with installation. Please
keep fingers away from the motor output gear whilst it is turning.
If your gate needs to open from the other direction (to the left, refer to Figure 3), your opener needs
to be mounted on the left-hand side as shown, the relative wires need to be swapped over, please
check under “Terminal Instructions” for swapping. (Factory default setting is for right-hand opening:
opener mounted on the right-hand side).
Figure 3
Any works done to the gate opener must be completed whilst the power is off, and the
opener is unplugged.
Press the first/top button
on the remote.
Rotating output gear will
drive the gate frame.
GA600AC Sliding Gate Opener User Manual
2
Parts List
Parts List (standard configuration)
No.
Picture
Name
Quantity
Note
1
Motor
1
2
Mounting Plate
1
3
Expansion Bolt M10×120
4
4
Manual Release Keys
2
5
Remote Control
2
6
Spring Limit Switch
Accessories Box/
Magnetic Limit Switch
Accessories Box
1
6-1-1
Spring Limit Switch Bracket
1
For use
when
installing
spring
switch
limit.
Spring Stop Mounting
Screw M6X10
4
6-1-2
Magnet Bracket
2
For use
when
installing
magnet
switch
limit
Magnets（S/N）
2
Magnetic Limit Switch Stop
Mounting Screws M6X18
4
Nuts M8
4
Flat Washers φ8
2
GA600AC Sliding Gate Opener User Manual
3
No.
Picture
Name
Quantity
Note
Spring Washers φ8
2
6-2
Nuts M10
4
6-3
Flat Washers φ10
8
6-4
Spring Washers φ10
8
6-5
Hexagon Head Bolt
M10×35
4
Note: Extra flat washers and spring washers are spare parts.
Parts List (optional)
No.
Picture
Name
Quantity
1
Galvanized Gear Rack
1m/pc
2
Nylon Gear Rack
1m/pc
3
Infrared Photocell
1 set
4
Wireless Keypad
1
5
Alarm Lamp
1
6
WIFI Adapter
1 set
Additional remote controls: Spare/Additional remotes for the automatic gate kit, these will need to
be paired to the motor.
Infrared photocell: Detects pedestrians, vehicles and objects that cross an infrared beam and
prevents the gate from closing.
Wireless keypad: Allows secure access through the gate used with a user set code.
Wired control: Allow users to control the opening and closing of the door through an external
push-button.
Alarm lamp: Alerts people near the gate and users that the gate is in operation.
GA600AC Sliding Gate Opener User Manual
4
Technical Parameters
Model
GA1000AC
Power Supply
110VAC/60Hz; 220VAC/50Hz
Motor Power
300W
Gate Moving Speed
12m/min
Maximum Loading Weight
1000KG
Remote Control Distance
≥30m
Remote Control Mode
Single button mode / Three button mode
Limit Switch
Spring limit switch / Magnetic limit switch
Working Noise
≤56dB
Working Duty
S2, 20min
Recording of up Remote Controls
25
Remote Frequency
433.92 MHz
Working Temperature
-20°C - +70°C
Overlook Size
293x247x300mm
Package Weight
16KGS
Installation
Before You Start
·GA1000AC Sliding Gate Automation Kit is suitable for powering the opening and closing motion
of gates up to 1000kg in weight, up to a length of 12m.
·Gate motion is achieved by the rotating output gear of the gate opener driving the gear rack
(sold separately) fitted to the moving gate.
·The gate opener requires you to press the remote control once to open, and once again to
close. This is a safety feature to ensure safe operation.
·The opener must be fitted within private property, never externally to a property’s boundary.
Any works done to the gate opener must be completed whilst the power is off and the
opener is unplugged. Any modifications/alterations/works to AC power components must
only be completed by a licensed electrician.
Tools Required
·Tape measure
·Level
·12mm concrete drill and hammer (when uses expansion screws)
·Phillips head screwdriver
·Straight screwdriver
GA600AC Sliding Gate Opener User Manual
5
Example Sliding Gate
Gate Track and Track Wheel Gate End Catch Gate Guide Rollers Gate Stop
Figure 4
Please ensure that the gate opener power cable is not plugged in at any stage before Step 9.
Step 1 - Gate Preparation
·Ensure that the sliding gate is correctly installed.
·The gate is horizontal and level and the gate can glide back and forth smoothly when moved by
hand before installing the gate opener.
·Wheels and guide rollers should rotate easily and be free from dirt or grime.
·Track should be flat, level and firmly affixed.
·Any misalignment in the gate will affect performance of the automatic gate opener.
Figure 5
The gate should slide smoothly by hand before attempting to install the gate opener.
GA600AC Sliding Gate Opener User Manual
6
Step 2 - Checking Manual Release
·Insert the key and open the manual release bar to enable the motor get into manual mode and
check that the motor output gear rotates freely by hand (Figure 6).
Figure 6
Step 3 - Removing / Installing Motor Cover
·Unscrew the two cover screws located at each side of the motor cover.
·Remove the rubber grommet below the limit switch (Figure 7).
Figure 7
Please Note: the rubber grommet must be fitted back onto the motor cover once the
cover has been re-fitted/replaced onto the base of the motor.
To make the motor into manual mode,
remove the slide cover, insert the key and
open the manual release bar.
In manual mode, the gear can turn freely
and the gate can be operated by hand.
GA600AC Sliding Gate Opener User Manual
7
Step 4 - Motor Pad Footing
·The motor pad concrete footing requires an area of no less than 450mm long x300mm wide
and a minimum depth of 200mm (Standard requirement).
·Ensure surface is level and parallel to the driveway.
Figure 8
Mounting Plate Dimensions
Use pencil, chalk or similar
tools to mark at the corners
of mounting plate
Indice
Altri manuali GATEXPERT Apricancello
GATEXPERT
GATEXPERT SL500DCL Manuale utente
GATEXPERT
GATEXPERT SL500DC Manuale utente
GATEXPERT
GATEXPERT DKC500ACL Manuale utente
GATEXPERT
GATEXPERT PY1200AC Manuale utente
GATEXPERT
GATEXPERT PY300DCL Manuale utente
GATEXPERT
GATEXPERT SW200DC Manuale utente
GATEXPERT
GATEXPERT SW400DC Manuale utente
GATEXPERT
GATEXPERT GA600AC Manuale utente
GATEXPERT
GATEXPERT GT800ACL Manuale utente
GATEXPERT
GATEXPERT GK Series Manuale utente
