GCC Technologies Jaguar J5-61 Manuale utente

V.4 2016 Dec.

Jaguar V Series

User Manual

http://www.GCCworld.com

V.4 2016 Dec.

NOTICE

GCC reserves the right to modify the information contained in this user

manual at any time without prior notice; un-authorized modification, copying

distribution or display is prohibited. All comments, queries or

suggestions concerning this manual please consult with your local dealer.

JaguarVUserManual

Important Information

Thank you for purchasing the GCC Jaguar V Cutting Plotter.

Before you use the cutting plotter, please make sure that you have read the

safety precautions and instructions below.

Caution

SAFETY PRECAUTIONS!

For safety concern, please always hold the cutter firmly from the bottom while moving

it. Do not move the cutter by clasping the depression area on both sides.

Do not shake or drop the blade holder, a blade tip can fly out.

During an operation, do not touch any of the moving parts of this machine (such as the

carriage). Also be careful to make sure that clothing and hair do not get caught.

Always connect the power cable to a grounded outlet.

Always use the accessory power cable which is provided. Do not wire the power cable

so that it becomes bent or caught between objects.

Do not connect the power cable to branching outlet to which other machines are also

connected, or use an extension cable. There is danger of overheating and of

mis-operation of the machine.

Keep the tools away from children where they can reach.

Always put the pinch rollers within the white marks.

Important Information

O (Correct)

Hold from the bottom X(Incorrect)

Hold the depression area

JaguarVUserManual

Important Information

Warning

Never press the top release grip and pull the bottom release grip at the same time as

the pictures shown below:

O (CORRECT) X(INCORRECT)

Press down

DISABLE

Press down

Stop bar

ENABLE

Pull up bottom to release grip

Note:

In case the grips clipped

together due to your

wrong operation, please

use a pair of tweezers to

pull out the stop bar

when pressing down the

top release grip. Keep

the stop bar outside then

release the grips as the

right figure.

Jaguar V User Manual

Table of Contents

Important Information

1. General Information

1.1 Introduction

1-1

1.2 Package Items

1-1

1.3Product Features

1-2

1.4 Appearance of Jaguar V

1.4.1 The Front View

1-3

1.4.2 The Back View

1-3

1.4.3 The Whole View

1-4

1.4.4 The Left-hand Side

1-4

1.4.5 The Right-hand Side

1-5

2. Installation

2.1 Precaution

2-1

2.2 Stand & Flexible Media Support System

2-2

2.3 USB Cable Tie and Saddle

2-8

2.4Desktop Flexible Media Support System

2-10

2.5Instruction of Damper Roller

2-12

2.6Blade Installation

2-13

2.7Automatic Blade Length Detection

2-15

2.8Cable Connections

2-17

2.8.1 USB Interface

2-17

2.8.1.1 Connecting your GCC cutter

2-17

2.8.1.2 Installing the driver

2-18

2.8.1.3 Driver Un-installation

2-21

2.8.2 RS-232 Interface

2-24

2.8.3 Ethernet Connection

2-24

2.8.4 Data Transmitting

2-29

2.8.5 Printer Sever Shared Setting

2-29

2.9 Software Installation

2-32

2.9.1 GreatCut Installation

2-32

2.9.2 Sure Cuts A Lot Installation

2-37

2.9.2.1 Auto Installation

2-37

2.9.2.2 Manually Activate Software

2-41

2.9.2.3 Re-install Sure Cuts A Lot Software

2-42

3. The Control Panel

3.1 The LCD Panel

3-1

3.2Menu in On-line Mode

3-2

3.3Menu in Off-line Mode

3-3

3.4 Menu Items

3-4

4. Operation

4.1 Media Loading

4.1.1 Loading the Sheet Media

4-1

4.1.2 Loading the Roll Media

4-3

4.2 Tracking Performance

4-5

Jaguar V User Manual

Table of Contents

4.3 Cutting Force and Offset Adjustment

4-7

4.4 How to Cut 3mm Letter

4-8

4.5 How to Make A Long Plot

4-8

4.6 When Completing the Cutting Job

4-9

4.7 Jaguar V Print Driver setting

4-10

4.7.1 Option Page

4-10

4.7.2 Paper Page

4-14

4.8 Reference Parameter setting for different materials

4-16

5. Automatic-Aligning System

5.1 Introduction

5-1

5.2 AAS Contour Cutting System

5-2

5.2.1 Notice for Registration Marks

5-2

5.2.2 AAS II on Jaguar V

5-3

5.2.3 Automatic Distinction of the Plot Direction

5-5

5.3 AAS Offset Test

5-6

5.4 Registration Mark Offset Range

5.5Contour Cutting

5-8

5.6Tips for AAS

5-10

6. Basic Maintenance

6.1 Cleaning the cutting Plotter

6-1

6.2 Cleaning the Grid Drum

6-2

6.3 Cleaning the Pinch Rollers

6-2

7. Trouble Shooting

7.1 Non-Operational Problems

7-1

7.2 Operational Problems

7-2

7.3 Communication Problems

7-3

7.4 Software Problems

7-4

7.5 Cutting Quality Problem

7-5

Appendix

A-1

Jaguar V Specification

A-1

A-2

Blade Specification

A-2

A-3

CorelDRAW Plug-In Instruction

A-3

A-4

Illustrator Plug-In Instruction

A-4

A-5

GreatCut Plug-In Instruction

A-5

A-6

SignPal 10.5 Instruction

A-6

A-7

Sure Cuts A Lot

A-7

Jaguar V User Manual

General Information 1-1

Chapter 1 General Information

1.1 Introduction

Jaguar V series cutting plotters have been designed to produce computer-generated images

or perform contour cutting on sheets or rolls of vinyl media.

This manual covers the following models of Jaguar V series cutting plotters:

‧J5-61(LX) for media width: 50mm(1.97”) ~ 770mm(30.3”)

‧J5-101(LX) for media width: 50mm(1.97”) ~ 1270mm(50”)

‧J5-132(LX) for media width: 50mm(1.97”) ~ 1594mm(62.7”)

‧J5-183LX for media width: 300mm(11.8”) ~ 1900mm(74.8”)

1.2 Package Items

The package of the Jaguar V model contents the items listed below, please check carefully.

If you find any item missing, please consult your local dealer for further assistance.

1. Cutting Plotter 1

2. Stand Set ( for J5-101/132/183 only ) (Optional for J5-61)

2 piece of T-shape stand

1 piece of stand beam

20 pieces of M6 screws

1 piece of M5 L-shape hexagon screw driver



1 piece of Installation Guide for Stand Set

Jaguar V User Manual

General Information 1-2

3. Flexible Media Support System Package

Items

183/132/101

1 set of Roll Media Flange (2 pieces)

1 set of Roll Holder (2 pieces)

1 set of Roll Holder Guide Bushes (4 pieces)

1 set of Roll Holder Support (2 pieces)

1 piece of M6 L-shape hexagon screw driver

1 piece of Installation Guide for Roll Holder

1 piece of M5 L-shape hexagon screw driver

1 set of Desktop Support Brackets (2 pieces)

4 pieces of Plastic Foot

4 pieces of M4 screws

12 pieces of M6 screws

1 piece of M4 L-shape hexagon screw driver

4. Accessories

1 piece of User’s Compact Disk

1 piece of AC power Cord

1 piece of data cable (USB cable: 3m)

1 set of Blade Holder Assembly (Installed in tool carriage of the

cutting

plotter)

1 piece of Blade (Installed in Blade Holder)

1 piece of Safe Blade

1 piece of Cutting Pad for Vinyl cutting

1 piece of Tweezers

1 piece of Promise Card

1.3 Product Features

The following are the main features of the Jaguar V series cutting plotters:

‧Triple-port connectivity provides you with greater flexibility

‧Up to 600 gram cutting force

‧Up to 1530 mm per second (60 ips) cutting speed (at 45° direction)

‧Guaranty 10-meter tracking

‧User friendly and multi-language control panel

‧Ingenious media basket (optional item)

‧Enhanced Automatic-Aligning System for automatic contour cutting

Jaguar V User Manual

General Information 1-3

1.4 Appearance of Jaguar V

1.4.1 The Front View (Figure 1-1)

1.4.2 The Back View (Figure 1-2)

Pinch Rollers –

hold the media during

cutting.

Lever –

raises or lowers the

pinch rollers.

Figure 1-2

Control panel – consists of 14

control keys and 1 LED and 1 LCM

showing messages and menus.

Cutting Pad –provides the

protection of blade when the blade is

cutting.

Tool Carriage – performs the

cutting with the installed blade

and pen with AAS module.

Alignment Rulers –

media can be aligned

with the clear guide line

marks.

Grid Drums – move

the media back and

forth during operation.

Slicer Groove –

slice off the extra

media easily along

this groove.

Platen – provides the

surface for holding and

supporting media while

performing cutting.

Figure 1-1

Jaguar V User Manual

General Information 1-4

1.4.3 The Whole View of Jaguar V (Figure 1-3)

Figure 1-3

Roll Holder – holds

and supplies the roll

media for cutting.

Roll Holder Guide

Bushes –serve to

keep the roll media in

place when media is

pulled from the roll.

T-Stand –supports

the cutting plotter

Stand Beam –

stabilizes the body.

Roll Holder

Support – supports

roll holders.

T-Stand –supports

the cutting plotter

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GCC Technologies Taglierina

GCC Technologies

GCC Technologies LaserPro X252RX Manuale utente

GCC Technologies

GCC Technologies i-Craft Manuale utente

GCC Technologies

GCC Technologies LaserPro SmartCut X380 Series Manuale utente

GCC Technologies

GCC Technologies AFJ-24S Manuale utente

GCC Technologies

GCC Technologies AFR-24S Manuale utente

GCC Technologies

GCC Technologies LabelExpress Manuale utente

GCC Technologies

GCC Technologies PII-132S Manuale utente

GCC Technologies

GCC Technologies LaserPro Mercury Manuale utente

GCC Technologies

GCC Technologies Expert II Manuale utente

Manuali Taglierina popolari di altre marche

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuale utente

Makita

Makita DCS552 Manuale utente

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuale utente

Makita

Makita 4112HS Manuale utente

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuale utente

Hitachi

Hitachi CM 4SB2 Guida alla risoluzione dei problemi

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuale utente

DeWalt

DeWalt XR LI-ION DCS350N Manuale utente

Baudat

Baudat ES1 Manuale utente

Mafell

Mafell ZAF 200 Guida

Makita

Makita 4100NH Manuale utente

Formax

Formax FD 574 Manuale utente

EINHELL

EINHELL TE-MA 1500 Manuale utente

Husqvarna

Husqvarna Cut-n-Break K 760 Manuale utente

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuale utente

TRI tool

TRI tool 301A Manuale utente

Roller

Roller King 1 1/4 Manuale utente

RODCRAFT

RODCRAFT RC7170 Manuale utente