GE Security 940 Manuale utente

Security

U.S.

T 888 GE SECURITY (1 888 437 3287)

F 561 998 6224

Asia

T 852 2907 8108

F 852 2142 5063

Australia

T 61 3 9259 4700

F 61 3 9259 4799

Europe

T 32 2 725 11 20

F 32 2 721 86-13

Latin America

T 305 593 4301

F 305 267 4300

www.gesecurity.com

460157001P/01-08

Model 94x, 97x Proximity Reader

Installation Manual

This document may not be copied or otherwise reproduced, in whole or in part,

except as specifically permitted under US and international copyright law,

without the prior written consent from GE.

Document number/460157001P (January 2008).

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT

NOTICE. GE ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS

AND SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR

OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE

USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE

LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE

AT WWW.GESECURITY.COM.

This publication may contain examples of screen captures and reports used in

daily operations. Examples may include fictitious names of individuals and

companies. Any similarity to names and addresses of actual businesses or

persons is entirely coincidental.

Trademarks

and patents

GE and the GE monogram are registered trademarks of General Electric.

Model 94x/97x Proximity Reader product and logo are trademarks of

GE Security.

Other trade names used in this document may be trademarks or registered

trademarks of the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet

and user documentation. For the latest product information, contact your local

supplier or visit us online at www.gesecurity.com.

FCC

compliance

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful inter-

ference to radio communications.

You are cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user's authority to

operate the equipment.

Regulatory

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Radio interference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Electrostatic discharge (ESD) precaution . . . . . . . . . . . . . . . . . . . . . . . . .2

Product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Back-to-back readers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

External tamper feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Mounting diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Configuring the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Selecting reader power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Selecting operating mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Selecting beeper sound level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Connecting the reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Wiring diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Testing the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Troubleshooting the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

All installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Unsupervised modes only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Supervised modes only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Regulatory approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Model 94x/97x Proximity Reader

Installation Manual

Figures

Figure 1. Recommended Additional Mounting Instructions

for External Tamper Switch Activation.............................. 11

Figure 2. Model 940 Reader - Gang Box Mounting.........................12

Figure 3. Model 940 Reader - Direct Wall Mounting.......................13

Figure 4. Model 941 Reader - Gang Box Mounting.........................14

Figure 5. Model 941 Reader - Direct Wall Mounting.......................15

Figure 6. Model 970/972 Reader - Gang Box Mounting ............... 16

Figure 7. Model 970/972 Reader - Direct Wall Mounting.............17

Figure 8. Model 971/973 Reader - Gang Box Mounting ............... 18

Figure 9. Model 971/973 Reader - Direct Wall Mounting.............19

Figure 10. Model 94x/97x Reader, J1 Connector and DIP

Switch Locations (PCB Assembly P/N 100079002

manufactured 12/02 or later)................................................ 22

Figure 11. (PCB Assembly P/N 100079001 manufactured |

prior to 12/02)................................................................................ 23

Figure 12. Wiring Diagram, Model 94x/97x

Supervised F/2F Mode............................................................... 30

Figure 13. Wiring Diagram, Model 94x/97x

Unsupervised F/2F Mode .........................................................32

Figure 14. Wiring Diagram, Model 94x/97x

Unsupervised Wiegand Mode ..............................................34

Figure 15. Typical Installation (Internal to the microcontroller)

Using Shielded Cable/Drain Wire......................................... 46

Figure 16. Typical Installation (External to the microcontroller)

Using Shielded Cable/Drain Wire......................................... 46

Introduction 1

Introduction

This manual is an installation guide for the GE Models 940, 941,

970, 971, 972, and 973 proximity readers. Throughout this guide,

the abbreviation 94x represents reader models 940 and 941. The

abbreviation 97x represents reader models 970, 971, 972, and

973.

The 94x and 97x readers while similar in functionality offer a

variety of features making them suitable for different

applications. The 94x and 97x readers are designed to mount on

standard U.S. gang boxes. The 94x readers are single-gang box

size. The 97x readers are sized for larger dual gang box

installation, offer greater badge read range, and a keypad option.

Models 940 and 970 give the greatest all-around badge read range

for their respective sizes, making them ideal for most

installations.

Models 941 and 971 are tuned for installation on metal mounting

plates. The standard metal mounting plate shields the reader from

the effects of a metal wall, which would otherwise dramatically

reduce the read range. The optional back-to-back metal mounting

plate shields the reader from the effects of a metal wall and makes

the reader unidirectional; ideal for direct back-to-back reader

installations.

Models 972 and 973 are dual gang size readers, identical to the

970 and 971 respectively, except for their built-in twelve-position

keypad. This feature makes these readers ideal for installations

requiring keypad PIN entry in addition to a valid badge read.

Model 94x/97x Proximity Reader

Installation Manual

Safety

Radio interference

Electrostatic discharge (ESD) precaution

WARNING: This is an FCC Class A product. In a domestic

environment, this product may cause radio

interference, in which case, the user may be

required to take adequate measures.

WARNING: Circuit board components are vulnerable to damage

by electrostatic discharge (ESD). ESD can cause

immediate or subtle damage to sensitive electronic

parts. An electrostatic charge can build up on the

human body and then discharge when you touch a

board. A discharge can be produced when walking

across a carpet and touching a board, for example.

Before handling any board, make sure you dissipate

your body’s charge by touching ground. This

discharges any static electricity build-up.

Product features 3

Product features

The GE Model 94x/97x Reader offers:

• Intelligent bidirectional communication between the

reader and microcontroller, which can be accomplished

up to 5,500 feet.

• The ability to read all ISO ProxLiteTM, ProxLite, and

Entrée badges and key tags.

• Field changeable DIP switches allow all 94x and 97x

readers to operate in one of four distinct operating

modes: Wiegand (4001), F/2F, Supervised, and Silent

Supervised.

• Rugged, weather-resistant, molded ABS construction

with integral backplate.

• Standard 12V operation.

• A clear, logical user interface with three LEDs and a

switch selectable beeper with volume control.

• Built-in tamper alarm also detects removal from wall.

• External tamper alarm option.

• Tactile keypad (Models 972 and 973 only) for Personal

Identification Number (PIN) input.

Model 94x/97x Proximity Reader

Installation Manual

System requirements

Host software • Secure Perfect®Edition 3.0 or later

•PicturePerfect

™1.7 or later

Microcontrollers • Micro/2

•Micro/4

•Micro/5-PXwith2RPor8RP

• Micro/5-PXN with 2RP or 8RP

• M5PXNplus with 2RP or 8RP

• Micro/PX-2000

• Micro/PXN-2000

• M2000PXNplus

• M3000PXNplus with 2RP or 8RP

Microcontroller

firmware

• For Micro/2 and Micro/4:

Secure Perfect: Version 5 or later

Picture Perfect: Version 1.7.0 or later

• For Micro/5-PX, Micro/5-PXN, Micro/PX-2000

and Micro/PXN-2000:

Secure Perfect: 3.1.0.6 or later

Picture Perfect: 1.7.0 or later

Badge and keytag

formats

•ISOProxLite

•ProxLite

•Entrée

•ProximityPerfect

Note: Proximity Perfect cards are obsolete

however they are supported by the Model

94x/97x readers.

Technical specifications 5

Technical specifications

For UL compliant installation notes, refer to “UL” on page 44.

Operating

temperature range

-31 F (-35 C) to +151 F (+66 C)

Relative humidity 5% to 95% (non-condensing)

Physical dimensions

Model 94x

Model 97x

(HxWxD)

4.75" (121 mm) x 2.9" (74 mm) x 0.90" (23 mm)

4.75" (121 mm) x 5.5" (140 mm) x 0.90" (23 mm)

Index of protection IP55

Color Light gray and black

Power supply Nominal 12VDC, 75mA, 150mA or 200mA

dependent on the power setting selected.

See Table 1 “Power level switch settings,” on page 24

Cable specifications Belden 8725 or equivalent, 20 AWG minimum,

shielded pairs

Maximum cabling

distancea

a. The reader will work well with unshielded cable in most environments. No

company, including GE, can guarantee that data will be reliably transmitted

over long distances on unshielded cable in every installation.

The maximum cable distance between the reader

and the microcontroller is influenced by a number of

factors including wire gauge and reader power level

setting. See Table 3 “Cable distances,” on page 25.

Read range Determined by the reader’s power level setting and

other environmental conditions. See Table 2 “Read

range by model number,” on page 24.

Pinouts The reader is supplied with a ten-wire cable. On one

end is a keyed connector that mates with the J1

connector on the back of the reader. The other ends

are stripped ready for connection to the field wiring

using a terminal block or in-line splice connectors.

Model 94x/97x Proximity Reader

Installation Manual

Parts list

• Model 940 Reader (single-gang) gray

• Model 940 Reader (single-gang) black

• Model 941 Reader (single-gang metal mount) gray

• Model 941 Reader (single-gang metal-mount) black

• Model 970 Reader (dual-gang) gray

• Model 970 Reader (dual-gang) black

• Model 971 Reader (dual-gang metal-mount) gray

• Model 971 Reader (dual-gang metal-mount) black

• Model 972 Reader (dual-gang with keypad) gray

• Model 972 Reader (dual-gang with keypad) black

• Model 973 Reader (dual-gang metal mount w/keypad) gray

• Model 973 Reader (dual-gang metal mount w/keypad) black

• Optional Tamper Key Tool

• 94x Plastic Backplate (gray)

• 94x Plastic Backplate (black)

• 97x Plastic Backplate (gray)

• 97x Plastic Backplate (black)

• Standard 941 Metal Mounting Plate (gray)

• Standard 941 Metal Mounting Plate (black)

• Standard 971/973 Metal Mounting Plate (gray)

• Standard 971/973 Metal Mounting Plate (black)

• Optional Back-to-Back 941 Metal Mounting Plate (gray)

• Optional Back-to-Back 971/973 Metal Mounting Plate

(black)

• 94x Weather-resistant Gasket

• 97x Weather-resistant Gasket

•ReaderCable

Refer to the GE Product Catalog for part numbers and ordering

information.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GE Security Sistema di sicurezza

GE Security

GE Security CareGard Manuale utente

GE Security

GE Security RLCDF Manuale del proprietario

GE Security

GE Security Phoenix A8950CC Manuale utente

GE Security

GE Security CareGard Manuale utente

GE Security

GE Security Simon XT V2 Manuale utente

GE Security

GE Security CONCORD Manuale utente

GE Security

GE Security Simon 60-875 Manuale utente

GE Security

GE Security Simon Manuale utente

GE Security

GE Security Simon Manuale utente

GE Security

GE Security Simon XT Manuale utente

GE Security

GE Security Concord 4 Manuale utente

GE Security

GE Security Simon XT Manuale utente

GE Security

GE Security Simon XT Guida utente

GE Security

GE Security 60-792-01-95R Manuale utente

GE Security

GE Security Concord 4 Manuale utente

GE Security

GE Security Concord 4 Manuale utente

GE Security

GE Security CS575 Guida utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente