GE Interlogix Manuale utente

Videoﬁed Upgrade

With

GE Interlogix

PRODUCT APPLICATION NOTE

Videofied Upgrade - GE Interlogix

Manufactured by RSI Video Technologies February 2013

Introduction: This document explains how to upgrade a GE Interlogix control panel with Videoﬁed Video Veriﬁcation

and interactivity. The GE Interlogix control panel upgrade requires a 12V SPDT (single pull double throw) relay. This document

covers basic relay module conﬁguration in addition to more detailed output function conﬁguration.

1. VIDEOFIED UPGRADE Conﬁgure GE Interlogix to Arm / Disarm Videoﬁed

STEP 1: CONFIGURE XTENDER MODE

DATE / TIME

DISARMED LVL: 1

ACCESS LEVEL

RIGHT ARROW to ACCESS LEVEL and press YES, RIGHT ARROW to ACCESS

LVL:4 and press YES. When prompted with BADGE OR CODE enter you

installer code + YES

www.videofied.com

Using the RIGHT ARROW go to CONFIGURATION and press YES. CONFIGURATION

GENERAL PARAMETERS

XTENDER

Press YES on GENERAL PARAMETERS

Using the RIGHT ARROW go to XTENDER and press YES

ARMING OPTION:

FROM THE HOST

With the display showing ARMING OPTION, press YES and use the arrow

keys to change it to FROM THE HOST and press YES

ENTRY DELAY

RIGHT ARROW to ENTRY DELAY and press YES. Set the value to 0 using

the alphanumeric keypad and press YES.

TRANSMISSION DELAY

RIGHT ARROW to TRANSMISSION DELAY and press YES. Set the value to 0

using the alphanumeric keypad and press YES.

ARMING CONFIRMATION

RIGHT ARROW to ARMING CONFIRMATION and press YES. Set the value to

0 using the alphanumeric keypad and press YES.

MODE

SLOW

RIGHT ARROW to MODE and press YES. Set the value to SLOW using the

arrows and press YES.

Press and hold the ESC/NO key for 5 seconds to return to the main menu.

STEP 2 - Wire and conﬁgure GE Interlogix Open Collector Output

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

Connect SPDT Relay Module to the GE Interlogix Series Control Panel

Enter Installer / Programming Mode

Enter *8 then installer code

Conﬁgure Output Function: Videoﬁed Upgrade to GE Interlogix series control panels requires

conﬁguration of one output function for arming and disarming.

ARM FUNCTION

Enter Address of 0 (zero)

to conﬁgure output number 4 (or go to next unprogrammed output option)

Enter Location 50

Enter 21 in segment 1 (21 = armed state)

Enter 2 in Segment 2

> Refer to control panel manual for table of conditions

Press exit button twice to exit

GE Interlogix

Output 1

Output 2

Output 3

Output 4

Aux +

Aux -

4 Terminal SPDT Relay

POS

NEG

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

Wiring Diagram - GE Interlogix to Videoﬁed Panel

Prog. Out. Com

Prog Output 2

Prog Output 1

Ref GND

Prog Input 3

Prog Input 2

Prog Input 1

Ref +

Ref GND

Arming Input 2

Arming Input 1

Ref +

PWR (-)

PWR (+)

Videofied Panel Terminal

Strip

GE Interlogix

Output 1

Output 2

Output 3

Output 4

Aux +

Aux -

4 Terminal SPDT Relay

NO C POS

NEG

Prog. Out. Com

Prog Output 2

Prog Output 1

Ref GND

Prog Input 3

Prog Input 2

Prog Input 1

Ref +

Ref GND

Arming Input 2

Arming Input 1

Ref +

PWR (-)

PWR (+)

Videofied Panel Terminal

Strip

GE Interlogix

Output 1

Output 2

Output 3

Output 4

Aux +

Aux -

4 Terminal SPDT Relay

NO C POS

NEG

12v

Power

Source

Note: Wiring will be different depending on if the Videoﬁed control panel is being powered by a 12v Power

Supply or directly off of the AUX -/+ built into the GE Interlogix system. Both options are shown below

Videoﬁed Powered by GE Interlogix

Videoﬁed Powered by 12v Power

2. TRIGGER AN INPUT ON VIDEOFIED PANEL WITH GE INTERLOGIX

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

STEP 1: CONFIGURE INPUT ON VIDEOFIED CONTROL PANEL

DATE / TIME

DISARMED LVL: 1

ACCESS LEVEL

RIGHT ARROW to ACCESS LEVEL and press YES, RIGHT ARROW to ACCESS

LVL:4 and press YES. When prompted with BADGE OR CODE enter you

installer code + YES

Using the RIGHT ARROW go to CONFIGURATION and press YES. CONFIGURATION

GENERAL PARAMETERS

PROGRAMMABLE INPUTS

Press YES on GENERAL PARAMETERS

Using the RIGHT ARROW go to PROGRAMMABLE INPUTS and press YES

PROGRAMMABLE INPUT

Using the arrow keys press YES on the PROGRAMMABLE INPUT 1

TRANSMISSION

Press YES on TRANSMISSION and choose the desired option using the

arrow keys and YES:

  •Enable-Inputislisteningallthetime

  •Disable-Inputisdisabled

  •OnlyIfArmed-Inputislisteningonlywhensystemisarmed

ALARM MODE

RIGHT ARROW to ALARM MODE and press YES. Use the arrow keys to

choose the desired option followed by YES.

  •Alarm-Eventistransmitted

  •Alarm/End-Eventandrestorearetransmitted

INPUT TYPE

CLOSED

RIGHT ARROW to INPUT TYPE and press YES. Use the arrow keys to choose

Closed and press YES

EVENT TYPE

RIGHT ARROW to EVENT TYPE and press YES. Use the arrow keys to select

the event the panel should report to the central station when the input is

triggered and press YES.

INPUT NAME

RIGHT ARROW to INPUT NAME and press YES. Use the alphanumeric

keypad to deﬁne a logical name to the input and press YES.

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

SIREN MODE

RIGHT ARROW to SIREN MODE and press YES. Use the arrow keys to

choose the desired siren option followed by YES.

Siren - Input trigger will sound all sirens

Silent - Input trigger will make no noise / feedback

Without Siren - Input trigger will beep keypad only

MAPPING

RIGHT ARROW to MAPPING and press YES. This gives you the option to

capture a video from a MotionViewer when the input is triggered. Use the

arrow keys to choose a installed MotionViewer from the list and press YES

Press and hold the ESC/NO key for 5 seconds to go back to the main screen.

STEP 2: CONFIGURE GE Interlogix OUTPUT

Enter Installer / Programming Mode

Enter *8 then installer code

Enter Address of 0 (zero)

* To conﬁgure output number 3 (or go to next unprogrammed output option)

Enter Location 49

Enter 24 in segment 1

Enter 2 in Segment 2

> Refer to control panel manual for table of conditions

Press exit button twice to exit

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

Wiring Diagram - Using a Videoﬁed Programmable Input

Prog. Out. Com

Prog Output 2

Prog Output 1

Ref GND

Prog Input 3

Prog Input 2

Prog Input 1

Ref +

Ref GND

Arming Input 2

Arming Input 1

Ref +

PWR (-)

PWR (+)

Videofied Panel Terminal

Strip

GE Interlogix

Output 1

Output 2

Output 3

Output 4

Aux +

Aux -

EMEA SALES

23, avenue du Général Leclerc

92340 BOURG-LA-REINE

FRANCE

Hotline: +33 (0)820 846 620

Fax: +33 (0)1 82 69 80 10

S2View®is a registered trademark of RSI VIDEO TECHNOLOGIES. Specications subject to change without notice.

USA SALES

1375 Willow Lake Blvd #103

Vadnais Heights, MN 55110

USA

Hotline: +1 877 206 5800

Fax: +1 651 762 4693

www.videofied.com

PRODUCT APPLICATION NOTEVideofied Upgrade - GE Interlogix

3. EXAMPLE APPLICATION FOR INPUT

OBJECTIVE: Conﬁgure any burglary condition on the GE Interlogix control panel to create a burglary condition on the

Videoﬁed panel and to report an intrusion signal to the central station with a video from MotionViewer 1

Videoﬁed Programmable Input Conﬁguration -

TRANSMISSION: ENABLED

ALARM MODE: ALARM - Event only is transmitted

INPUT TYPE: OPEN

EVENT TYPE: INTRUSION

INPUT NAME: GE BURG

SIREN MODE: SIREN

MAPPING: MOTIONVIEWER 1

GE Interlogix Output Function Conﬁguration -

Activated On: 0 - Zone Address

Zone Address: 49 -Output location (Output 3 = 49)

Segment 1: 24 - Not Ready

Segment 2: 2 - On if output should latch off if output should be timed

Altri manuali GE Pannello di controllo

GE SIMON XT Manuale utente

GE Allegro 60-874-95R Manuale utente

GE Kilsen KFP-CF Series Manuale utente

GE SIMON XT Manuale utente

GE EST iO64 Manuale del prodotto

GE NetworX NX-6 Manuale di installazione

GE NetworX Series Manuale di installazione e funzionamento

GE Advisor MASTER ATS111 series Manuale utente

GE Interlogix ARITECH ATS1211 Manuale utente

GE ZITON ZP3 Manuale utente

GE NetworX NX-6V2 Manuale utente

GE ATS4000 Istruzioni operative

GE NX-1308E - Caddx 8 Zone LED Keypad Manuale di installazione

GE QuickPanel+ IC755CxS06RDx Manuale utente

GE Entelli-Switch 250 Manuale utente

GE NX-4-EUR Manuale utente

GE SIMON XT Istruzioni operative

GE Kilsen KFP-CF2 Manuale utente

GE SIMON XT Manuale utente

GE IC754CSF15CTD Manuale di installazione

GE Multilin 889 Manuale utente

GE 45633 Manuale utente

GE NX-4V2 Manuale di installazione

GE NetworX NX-6V2 Manuale di installazione

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche