GE FPDW Manuale utente

IMPORTANT: Read and save these instructions.

Washer & Dryer Pedestal Kit

This kit is intended to be installed by persons having electrical and mechanical training and a

level of knowledge considered acceptable in the appliance repair trade.

Your safety and the safety of others are very

important. Many important safety messages are

provided in these instructions and on your

appliance. Always read and obey all safety

messages.

EXCESSIVE WEIGHT HAZARD

Two or more people may be required to move and

install the washer & dryer with pedestals.

Failure to comply may cause back or other injury.

Tools needed:

Level

9/16" open end wrench or ratchet

Channel-lock adjustable pliers

2# Phillips screwdriver

Flat blade screwdriver

WASHER INSTALLATION

Washer Hardware

Remove the 24-3/8" x 27" x 12"pedestal,

installation hardware and instructions from the

shipping carton.

Using the pedestal shipping carton for

protection, carefully lay the washer on its back.

NOTE: If washer was previously installed,

disconnect from power supply, remove inlet

hoses from water faucets and tape the drain hose

to the top front of the washer to eliminate excess

water on the floor.

Remove the four (4) leveling legs from the

washer base and discard.

If the washer has rollers, remove the four (4)

screws securing the rollers to the base.

Install the four (4) leveling legs (supplied with

the kit) fully into the pedestal.

The words "TOP FRONT" are embossed on the

top front of the pedestal. Position the pedestal so

the words are up with the front of the washer.

Align the pedestal mounting holes with the

threaded leg holes on the washer base.

.Attach the pedestal to the washer using the four

(4) 3/8" X 1" bolts, 3/8" lock washers and 3/8"

flat washers. DO NOT TIGHTEN BOLTS

COMPLETELY!

8. Align the sides of the washer/dryer with the

pedestal and tighten the bolts with a 9/16"

wrench or ratchet.

9. Carefully raise the washer/pedestal assembly to

the upright position. NOTE: Because of the

increased weight caused by the addition of

the pedestal, two or more people may be

required.

NOTE: Disregard Steps 10 &11 if the washer

has an electronic console.

10. Remove the dispenser drawer by first sliding the

safety latch to the right, then pulling the drawer

out until it stops. Reach back into the left corner

of the drawer cavity, press down firmly on the

lock tab (left portion of the drawer) and pull out

the drawer.

11. Remove the paper backing from the foam pads

and apply to the areas shown below. NOTE:

The adhesive backing must be applied to the

rear surface of the drawer area. Replace the

dispenser drawer.

12. Refer to the installation instructions that came

with the washer to properly complete water,

drain and electrical connections. NOTE: Since

the pedestal will increase the washer height 12

inches, the minimum standpipe height will

increase from 24 inches to 36 inches. If

questions arise, please refer to the owner's

manual that came with the washer for contact

information.

NOTE: The washer/pedestal assembly MUST

be on a solid floor and level for proper

operation. Turn the lock nut on each leveling leg

up towards the pedestal base and snug with a

wrench. Keep the leg extension at a minimum to

prevent excessive vibration.

DR YER INS TALLA TION

cer Hardware

Remove the pedestal, installation hardware and

instructions from the shipping carton.

Using the pedestal shipping carton for

protection, carefully lay the dryer on it's back

and remove the four (4) leveling legs from the

dryer base.

.Insert the flat blade screwdriver in the slots

between the front panel & base. Pry downward

to remove the hole plugs located in the bottom

of the dryer front panel.

.Position the dryer on top of the pedestal. Slide

the back of the dryer into the rear mounting

brackets and then slide the front of the dryer

onto the pedestal and bracket. NOTE: Two or

more people may be required.

Install the four (4) leveling legs (supplied with

the kit) fully into the pedestal.

The words "TOP FRONT" are embossed on the

top front of the pedestal. Using four (4) 8-18 x

3/8" self-tapping screws (supplied with the kit),

attach the front mounting brackets to the top

front of the pedestal. Tighten securely.

.Insert the two (2) 10-16 x 1" screws (supplied

with the kit) through the holes in the dryer front

panel and install into the front mounting

brackets. Tighten securely

.Using four (4) 8-18 x 3/8" self-tapping screws

(supplied with the kit), attach the rear mounting

brackets to the rear of the pedestal. Tighten

securely.

10.

Reinstall the hole plugs removed in step 2.

Refer to the installation instructions that came

with the dryer to properly complete electrical

and venting connections. If questions arise,

please refer to the owner's manual that came

with the dryer for contact information.

NOTE: The dryer/pedestal assembly MUST be

on a solid floor and level for proper operation.

Turn the lock nut on each leveling leg up

towards the pedestal base and snug with a

wrench. Keep the leg extension at a minimum to

prevent excessive vibration.

WARRANTY

Full One Year Warranty on Mechanical Parts

For one year from date of purchase, when this pedestal is installed with the listed washer or dryer (see

owners manual for specific model) and operated according to the information in the Use and Care Guide,

Operating Instructions and Installation Instructions, the supplier will replace any of its mechanical parts if

they are defective in workmanship or material. Keep your bill of sale. The date of the bill establishes the

warranty period should parts be required. This written warranty gives you specific rights. You may also

have other rights which vary from state to state.

Warranty Restriction

If the pedestal is used for any other purpose than private family use or used with any product that requires

modification for installation, the warranty is null and void.

Warranty Parts

Warranty parts are available by contacting the supplier where the pedestal was purchased or refer to the Use

and Care Guide that came with the washer or dryer that is installed on the pedestal for contact inforlnation.

Altri manuali GE Elettrodomestico per lavanderia

GE Spacemaker WSM2780 Manuale utente

GE Spacemaker WSM2420S Manuale utente

GE Spacemaker WSM2780 Manuale utente

GE 49-90280 Manuale utente

GE Spacemaker WSM2780 Manuale utente

GE Spacemaker WSM2700 Manuale utente

GE Spacemaker WSM2780 Manuale utente

GE Spacemaker WSM2480 Manuale utente

GE WSM2700WWW - 27" Unitized Spacemaker Washer Manuale utente

GE Spacemaker WSM2420S Manuale utente

GE Spacemaker WSM2700 Manuale utente

GE Spacemaker GTUP270EMWW Come usare

GE Spacemaker WSM2000H Istruzioni per l'installazione

GE Unitized Spacemaker WSM2420 Manuale utente

GE Spacemaker WSM2700 Manuale utente

GE Spacemaker Laundry WSM27TH Manuale utente

GE Spacemaker WSM2700R Manuale utente

GE Spacemaker WSM2700L Manuale utente

Manuali Elettrodomestico per lavanderia popolari di altre marche

LAUNDRY JET

LAUNDRY JET Plus Manuale utente

LG WKGX301H A Series Manuale utente

Kenmore

Kenmore Kenmore 27" Wide LAUNDRY CENTER Washer -... Manuale utente

LG WK X30 Series Manuale utente

Frigidaire

Frigidaire GLEH164DS1 Guida per l'amministratore

Frigidaire

Frigidaire GLEH1642DS0 Guida per l'amministratore

AEG

AEG LAVATHERM 65280AC Manuale utente

Samsung

Samsung WF0500NXWG Manuale utente

Whirlpool

Whirlpool WVP5000SQ0 Manuale utente

Whirlpool

Whirlpool XVP8600TB0 Manuale utente

Frigidaire

Frigidaire MEX731CFS2 Manuale utente

Asko

Asko Washer/Dryer Combination Laundry System Manuale utente

Aerus

Aerus LAUNDRY PRO Manuale utente

Frigidaire

Frigidaire FLCE752CAW Manuale del proprietario

Mustee

Mustee UTILATUB 17F Manuale utente

Whirlpool

Whirlpool XVP9000TA0 Manuale utente

Frigidaire

Frigidaire GLGT1142CS1 Guida rapida

LAUNDRY JET

LAUNDRY JET ISense Manuale utente