GE VAT2000 Series Manuale utente



GE Power Controls

PCST-3299E-R0

VAT2000 AC Drive Series

U2KV23DN1

Speed Detection Feedback

INSTRUCTION MANUAL

NOTICE

1. Read both this manual and VAT2000 Instruction Manual (ST-

3251) before using the U2KV23DN1, and store in a safe place for

reference.

2. Observe the warnings, cautions and other matters described in

this manual.

3. Make sure that this manual is delivered to the final user.

4. The content of this manual can be changed without notice

GE Power Controls

U2KV23DN1 Instruction Manual

- -1

1. Specifications

This manual is for Speed detecting option PCB U2KV23DN1.( Card NPQF-DN09). The option allows

the use of a standard complimentary encoder for speed detection feedback.

Encoder specifications:

Item Specifications

Supply voltage 12VDC±1.2V

Output method Complimentary

Output pulse voltage VH(High revel pulse voltage):above 8.0V , VL(Low revel pulse

voltage):below 1.0V at the terminal on V23-DN1.

Supplied current 150mA (Including signal currents) (Refer Note2 on page 2)

Rising/falling time Within 1µs

Output signal 90º±30º phase difference signal(A phase pulse, B phase pulse)

(Refer Note3 on page 2)

Output pulse

frequency The output pulse frequency is required within 60±10kHz when the

motor rotates at the max. speed.

2. Installation

a) Confirm that the Jumper W1 on U2KV23DN1 is set to 1(2PP) side.

b) Remove the front cover of VAT2000S

CAUTION

There is a risk of electric shocks.

The VAT2000S has a built-in electrolytic capacitor, so a charge will remain even when the inverter power is turned OFF. Always

observe the following times before carrying out wiring work.

• Wait at least 20 minutes after turning the power OFF before starting work. Make sure that thedisplays on the operation panel

have gone out before removing the cover.

• After removing the cover, confirm that the "CHARGE" LED in the VAT2000S does not light. Also check that the voltage

between terminals L+1 or L+2 and L– is 15V or less before starting the inspections. (Check with the "CHARGE" LED if the

unit is not provided with the L– terminal.)

c) Install U2KV23DN1 to the position Option I on the Control PCB cover and make sure not to bend the

pins of reverse of U2KV23DN1.

U2KV23DN1 Instruction Manual

- -2

3. Wiring

An example of the encoder connection is given below.

Note 1: The option U2KV23DN1 is card number NPQF-DN09.

Note 2: If the current to encoder exceeds 150mA, use an external power supply. In this case, connect

the external power source only to the encoder. DO NOT connect the power source to TB1-

1,2[12KP] or -3[0KP] on U2KV23DN1.

Note 3: Below drawing shows A, B encoder phases when motor rotates forward.

A phase

pulse

B phase

pulse

90º 90º 90º 90º

12V

2.2KΩ

1KΩ

470

TB1

-1,2[12KP]

-3[0KP]

-7[PA]

-8[0KP]

-9[PB]

-10[0KP]

DC12V Max.150mA

(Refer Note2 on page 2)

[A phase pulse output]

[B phase pulse output]

[common]

-11[PAOUT]

-13[PBOUT]

-12,-14[0KP]

A phase

pulse

B phase

pulse

Set W1 to 1(2PP)side.

2PP

Suitable cable for encoder

0.75mm2(50m or less), 6-core twisted shield strands

U2KV23DN1(NPQFDN09)

1PP

Encoder

3.3KΩ

12V

ENCODER

DC12V Max.150mA

TB1

-1,2[12KP]

-3[0KP]

U2KV23DN1

12V

Power

source

Altri manuali per VAT2000 Series

Indice

Altri manuali GE Sensore di sicurezza

GE H-10 Manuale operativo

GE EV435AM-AD Series Manuale utente

GE VE1100 Series Istruzioni per il montaggio

GE 250-CO Istruzioni per il montaggio

GE RCR 50 - Security PrecisionLine Dual Technology Motion... Manuale utente

GE DD205-AD Series Manuale utente

GE KL700 Series Manuale

GE AP950PI - Security High-Security PIR Motion... Manuale utente

GE Motion Sensor Manuale utente

GE VE1012 Series Istruzioni per il montaggio

GE KL700 Series Manuale utente

GE PrecisionLine RCR-90 Manuale utente

GE INDOOR/OUTDOOR PIR MOTION SENSORS... Manuale utente

GE 868 GEN2 Manuale utente

GE VersaSafe VersaPoint Series Manuale utente

GE Interlogix AP100PI Manuale utente

GE 45132 Manuale utente

GE Baker Hughes Reuter-Stokes Flame Tracker... Manuale utente

GE GS930 Manuale utente

GE ARITECH 1500 Series Manuale del prodotto

GE Choice Alert Manuale utente

GE 50487 - Ultrasonic Sensor Parking Alert Manuale utente

GE EV1000PI Series Manuale utente

GE DD205RF/60-947-8A Series Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente