GE GCG1500 BB Manuale utente
Installation
Instructions
15” Built-In Compactors
GCG1580 SS
GCG1500 BB
GCG1500 WW
GCG1700 II*
ZCGS150 SS
ZCGP150 II*
*For ZCGP150 II and GCG1700 II,
also refer to the instructions
provided on the template packed
with those models.
Safety Information
CAUTION:
For personal safety, remove house fuse or
oven circuit breaker before beginning
installation to avoid severe or fatal
shock injury.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT – Save these instructions for
local inspector’s use.
• IMPORTANT – Observe all governing codes
and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
•Skill Level – Installation of this appliance requires
basic mechanical and electrical skills.
•Completion time – 1 hour.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty. See Owner’s Manual
for warranty information.
IMPORTANT
• Use this compactor only for its intended purpose.
• This compactor is designed for BUILT-IN
installations ONLY.
2
CONTENTS
Design Information
Models Available .............................................................. 3
Product Dimensions and Clearances............................ 3
Tools Required .................................................................. 3
Parts Supplied .................................................................. 3
Advance Planning
Clearances ........................................................................ 4
Models with a Custom Drawer Panel .......................... 4
Installation Preparation
Electrical Requirements ................................................ 5
Grounding Requirements ................................................ 5
Unpacking the Compactor .............................................. 6
Leveling the Compactor .................................................. 7
Adjusting the Retaining Bracket .................................... 7
Adjusting the Base Toekick ............................................ 7
Installation Instructions
Position the Compactor under the Countertop............ 8
Attach the Compactor to the Countertop .................... 8
Reinstall the Compactor Drawer.................................... 9
Installation of the Trash Bag Caddy .............................. 9
Finalize Installation .......................................................... 9
WARNING!
Do not allow items to fall or collect behind
the compactor. Failure to follow this
instruction could result in a fire.
MODELS AVAILABLE
GCG1580 SS
GCG1500 BB
GCG1500 WW
GCG1700 II*
ZCGS150 SS
ZCGP150 II*
*For ZCGP150 II and GCG1700 II, also refer
to the instructions provided on the template
packed with those models.
3
Design Information
PRODUCT DIMENSIONS AND CLEARANCES
TOOLS REQUIRED
• Level
• Phillips Screwdriver
• Pliers
• Gloves
• Measuring Tape
PARTS SUPPLIED
• 6 mounting screws (located in the literature package)
• 2 countertop retaining brackets
• 2 side mounting clips
34″(86.4 cm)
to
35″ (88.9 cm)
15-1/8″
(38.4 cm)
min
24″ (61 cm)
min
Locate the outlet 18” (45.7 cm) min
from the floor, 3” (7.6 cm) min from
either side
33-3/4″
(85.8 cm)
min.
to
35″(88.9 cm)
max.
14-7/8″ (37.8 cm)
23″ (58.4 cm)
• Allow 23″(58.4 cm)
clearance at the front for
a full drawer opening.
• Allow 6″(15.2 cm)
clearance on the right
side to the nearest
vertical wall or cabinet
for bag removal.
•Note: This compactor is
designed for built-in
applications only.
4
ADVANCE PLANNING
MODELS WITH A CUSTOM
DRAWER PANEL
Models ZCGP150 II and GCG1700 II
The custom drawer panel and custom handle of your
choice should be secured to the compactor before
installation begins. A template with instructions and
installation hardware is provided with those models.
For planning purposes, you may order the template in
advance. Order Pub. No. 31-30597. Complete panel
installation instructions are included on the template.
CUSTOM PANEL SIZE REQUIREMENTS:
Maximum panel weight is 12 LBS (5.4 kg).
CLEARANCES
• You should be able to fully open the compactor
drawer. Six inches (15.2 cm) is required on the right
side of the compactor for bag removal.
• Allow 23 inches (58.4 cm) in front of the compactor
to remove the drawer.
• This compactor is designed as a built-in
appliance only. It may be located in any
convenient space under a countertop.
DO NOT OPERATE FREE-STANDING.
• The compactor may be installed beneath
countertops of stone or other materials that will
not accept screws. No trim kit is required.
The compactor must be securely installed in a cabinet
that is firmly attached to the house structure. Weight
on the compactor drawer could cause the compactor
to tip and result in injury. Never allow anyone to
climb, sit or hang on the compactor drawer.
29-5/16″
(74.5 cm)
14-7/8″
(37.8 cm)
3/4″
(1.9 cm)
Thick
Custom
Panel
5
Installation Preparation
ELECTRICAL REQUIREMENTS
WARNING!
FOR PERSONAL SAFETY: Remove house
fuse or open circuit breaker before
beginning installation. Do not use an
extension cord or adapter plug with
this appliance.
• The power supply cord and plug should be brought
to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 36" (91.4 cm) power cord.
• This appliance must be supplied with 120V, 60Hz
and connected to an individual properly grounded
branch circuit, protected by a 15 or 20 ampere
circuit breaker or time delay fuse.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
IMPORTANT: Observe all governing codes and
ordinances.
GROUNDING REQUIREMENTS
WARNING!
The improper connection of the equipment
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service representative if you
are in doubt that the appliance is properly
grounded.
• Electrical Ground is REQUIRED on this compactor.
• DO NOT ground to a gas pipe.
• DO NOT change the power supply cord plug. If it
does not fit the outlet, have a proper outlet installed
by a qualified electrician.
• DO NOT have a fuse in the neutral or grounding
circuit. A fuse in the neutral or grounding circuit
could result in an electrical shock.
• DO NOT use an extension cord with this compactor.
Failure to follow these instructions could result in
death or serious injury.
Recommended Grounding Method:
For your personal safety, this appliance must be grounded.
This appliance is equipped with a power supply cord having
a 3-prong grounding plug. To minimize possible shock
hazard, the cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in accordance
with the National Electrical Code ANSI/NFPA70—latest
edition* and all local codes and ordinances. If a mating wall
receptacle is not available, it is the personal responsibility
and obligation of the customer to have a properly grounded
3-prong wall receptacle installed by a qualified electrician.
3-prong grounding-type
wall receptacle
3-prong
grounding
plug
Grounding
plug
Power
supply
cord
Copies of the standards
listed may be obtained from:
* National Fire
Protection Association
Batterymarch Park,
Quincy, MA 02260
Installation Preparation
6
UNPACKING THE COMPACTOR
1
• Move the compactor close to the installation
location.
• Use a section of the shipping carton to protect the
finished floor.
• Do not use the handle to lift the compactor.
• Remove all protective packaging materials such as
tape or shipping pads. Remove waxy residue caused
by shipping material with a mild solution of liquid
household cleaner and water.
• Check that the power supply cord is attached to the
cord clip on the rear of the compactor.
IMPORTANT: Use the shipping carton as a pad.
Do not slide the compactor across a finished floor.
Damage will occur.
Cord clip
UNPACKING THE COMPACTOR
(CONT.)
• Open the compactor drawer and remove any
shipping materials or other items shipped in the
drawer.
• Do not remove the compactor bag (if installed).
• Grasp the sides of the drawer and lift it out of the
compactor. Place the drawer on a protected surface.
The drawer can scratch a finished floor.
7
Installation Preparation
LEVELING THE COMPACTOR
2
• The top of the compactor should be at least 1/8″
(3 mm) from the top of the cabinet opening. You can
adjust the height of the compactor by turning the
screws on the front leveling legs and rear wheels.
• Place a level inside the compactor on the floor
of the cabinet.
• Use the leveling legs to adjust level front to back and
side to side.
Front leveling legs
Rear wheels
ADJUST THE RETAINING
BRACKET
3
• Determine installation depth of the compactor
beneath the countertop.
• Adjust the position of the retaining brackets so that
the screws can meet the underside of the
countertop.
• Mounting clips are provided for stone or other hard
countertops that will not accept screws.
Retaining
bracket
Countertop
ADJUSTING THE BASE TOEKICK
4
A toekick extension is supplied. It can be used to cover
any gaps from the bottom of the compactor to the floor.
• Remove the top toekick screws as shown. Lift off top
toekick piece.
• Loosen the base toekick screws, adjust to touch the
floor and tighten the screws.
• Reinstall the top toekick piece with the original
screws.
Loosen screw
on each side
Top toekick
Adjustable
lower toekick
• Use two #8-18 x 1/2″(45.7 cm x 1.3 cm) mounting
screws to fasten the retaining brackets at the top
of the compactor to the underside of the countertop.
• If the brackets cannot be attached to the underside
of the countertop, attach mounting clips to the
bracket. Fasten the compactor to the cabinet front
with mounting screws through the mounting clips.
8
Installation
POSITION COMPACTOR UNDER
THE COUNTERTOP
5
WARNING!
When moving the compactor, use gloves to
protect and cushion your hands.
To protect the finished flooring, use a dolly
to move the compactor near the installation
location.
Failure to follow these instructions could
result in injury.
• Plug the power cord into a properly grounded
receptacle.
• Carefully lift the front of the compactor slightly and
roll the unit into the cabinet opening until the
retaining brackets stop.
Lift here
ATTACH THE COMPACTOR TO
THE COUNTERTOP
6
Mounting
screws
Retaining
bracket
Mounting
screw
Retaining
bracket
Mounting
clip
9
Installation
• Grasp the sides of the drawer. Carefully slide the
drawer into the compactor.
REINSTALL THE COMPACTOR
DRAWER
7
• Set the bag caddy into the drawer and hook the
pre-punched holes in the caddy on the drawer
buttons.
• Set the trash bag into the bag caddy and fold over.
• Hook the holes in the bag over the drawer buttons.
INSTALLATION OF THE TRASH
BAG CADDY (on some models)
8
Drawer
buttons
Trash
bag
caddy
• Turn power on at the source.
• Refer to your Owner’s Manual for operating
instructions.
FINALIZE THE INSTALLATION
9
10
Notes
Altri manuali per GCG1500 BB
2
Questo manuale è adatto per i seguenti modelli
11
Indice
Lingue:
Altri manuali GE Compattatore di rifiuti
GE
GE UCG1680 Manuale utente
GE
GE GCG1700II Manuale utente
GE
GE GE PROFILETM GCG1500L Manuale
GE
GE 165D4700P385 Manuale utente
GE
GE GCG1500P Manuale utente
GE
GE GCG1700LII Manuale
GE
GE GCG1580PSS - ProfileTM 15" Compactor0 Manuale
GE
GE Monogram Compactor Manuale utente
GE
GE Monogram ZCG3100VBB Manuale utente
GE
GE UCG1520NSS Manuale utente
GE
GE Monogram ZCG3500DSS Manuale utente
GE
GE ZCGP150 II Manuale utente
GE
GE GCG1520 Guida di sicurezza
GE
GE MONOGRAM ZCG3300 WW Manuale utente
GE
GE UCG1600 Series Manuale utente
GE
GE GCG1200 Manuale utente
GE
GE UCG1510N0II Manuale utente
GE
GE GCG17 - Profile 1.4 cu. Ft. Compactor Manuale
GE
GE MONOGRAM ZCGP150LII Istruzioni utente
GE
GE GCG1700P Manuale
Manuali Compattatore di rifiuti popolari di altre marche
Whirlpool
Whirlpool GX900QPLQ - 15" Trash Compactor Manuale utente
Vestil
Vestil FM-T-DUMP Manuale utente
Euro Shatal
Euro Shatal RP4014-50 Manuale utente
third coast equipment
third coast equipment SP3410 Manuale utente
Cucine Oggi
Cucine Oggi EKKO CUBE 40 9000 Manuale utente
Viking
Viking Designer Series Manuale utente
