GearBest DWR02 Manuale utente
Dual Band Wi-Fi Repeater
2.4GHz&5GHz Concurrent
Quick Installation Guide
Open Source Code
This product includes software codes developed by third parties. These software
codes are subject to either the GNU General Public License (GPL), Version 2, June
1991 are GNU Lesser General Public License (LGPL), Version 2.1, February 1999.
You can copy, distribute, and/or modify in accordance with the terms and conditions
of GPL or LGPL.
The source code should be complete, if you want us to provide any additional
Source code files under GNU General Public License (GPL), please contact us. We
are committed to meeting the requirements of the GNU General Public License
(GPL). You are welcome to contact us local office to get the corresponding software
and licenses. Please inform us your contact details (full address) and the product
code. We will send you a CD with the software and license for free.
Please refer to the GNU GPLWeb site for further information.
http://www.gnu.arg/licenses.en.html
Introduction
The Dual-band Wi-Fi Repeater broaden the range of your wireless network. The
Dual-Band Mode enables the simultaneous sending and receiving of 2.4GHz and
5GHz wireless signals. Thus the dual-band Wi-Fi Repeater can be used in 2.4GHz
and 5GHz wireless networks. The dual-band Wi-Fi Repeater supports the following
three modes: Repeater/AP/Client.
Package Contents
Before you starting to use this Repeater router, please check if there's anything
missing in the package, and contact your dealer of purchase to claim far missing
items:
1 x DuaI Band Wi-Fi Repeater
1x RJ-45 Networking Cable
1x Quick installation Guide
01
Getting Started
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown below), please do the following:
Wireless Repeater Mode
The range of your wireless network is
extended and made available for 2.4GHz
and 5GHz wireless networks
You will need Wireless AP/Router
Internet access
Wireless AP Mode
You will need broadband Router Internet
access
Connect the Wi-Fi Repeater to your Router/
Switch with RJ-45 Cable
Client Mode
You can connect an end device with a LAN interface (for example, computer,
notebook or TV set), which has no own wireless network, to the Wi-Fi Repeater
via a LAN cable (network cable). The Wi-Fi Repeater can now connect your end
device wirelessly to an existing wireless router.
02
Default Parameters
Default IP:192.168.10.1
URL: http://w.ap
Login Name: admin
Password: admin
Wireless SS/D:
Wi-Fi Repeater(2.4G)
Wi-Fi Repeater(5G)
Wireless Key: no
03
LED indicators
LED Status Meaning
Lights up Excellent reception, signal strength
50% to 100%
Flashes slowly Good reception, signal strength 25% to
50%
Flashes rapidly Weak reception, signal strength below
25%
2.4G signal
5G signal
Off NO reception
Lights up The Wi-Fi Repeater is switched on
Flashes WPS connection is established or WPS
signal of another device is expected
Power/WPS
Off The Wi-Fi Repeater is switched off
Flashes slowly Connection established to wireless
network
Flashes rapidly Data is being transferred
Wireless
Off Connection not established to wireless
network
Lights up LAN connection is established
Flashes Data is being transferred
LAN
Off LAN connection is not established
04
Configure the Wireless Repeater Mode
This is the easiest way to configure the Wi-Fi Repeater, First, check whether your
wireless router supports WPS. For further details, please read the operating
instructions for your wireless router.
1. The mode selector must be set to the "Repeater" position for Repeater Mode.
2. Plug the Wi-Fi Repeater into a wall socket.
3. Then switch on the Wi-Fi Repeater by turning the Power switch to "ON"
Position.
4. Press the WPS button on the Wi-Fi Repeater for at least 6 seconds.
The Power/WPS LED now flashes for approx. 2 minutes.
5. Within these 2 minutes, please Press the WPS button of the AP/Router directly
for 2 - 3 seconds. (For further details, please read the operating instructions
for your wireless router.)
The Wi-Fi Repeater then automatically connects to your wireless router and copies
wireless key of the settings, Once the connection has been successfully established,
the 2.4G or 5G signal LED lights up. The Wi-Fi Repeater can then be used. The
Wi-Fi Repeater can be accessed via the SSID and the wireless key of your wireless
router.
Note: If the WPS session overlap, WPS will not be able to start
05
A. Configure the Wi-Fi Repeater wirelessly
You can configure the Wi-Fi Repeater by connecting it with you computer/laptop
with enclosed RJ45 cable or wirelessly.
A1. The mode selector must be set to the
“Repeater” position for Repeater Mode.
A2. Plug the Wi-Fi Repeater to a wall socket.
A3. Click on the network icon or on
the right bottom of your desktop. You will
find the signal from the Wi-Fi Repeater
(2.4G) or Wi-Fi Repeater(5G). Click on
“connect” then wait for a few seconds.
A4. Open web browser and type
http://192.168.10.1 or http://w.ap
in the browser address box. This number
is he default IP address for this device.
Note: please check whether the Wi-Fi Repeater accord with factory default Settings
once you can’t entered http://192.168.10.1. If you are still not sure what reasons,
you can reset the Wi-Fi Repeater, just need to press the reset button for 8 seconds,
then try again.
06
A5. The login screen below will appear. Enter the User Name and Password then
Click “Submit” to login. The default User Name is “admin” and Password is
“admin”
A6. After logging in, you will see the web page below: Click on the Repeater button
in the Wizard field.
07
A7. From the list, select a wireless network with which you want to connect the Wi-Fi
Repeater by choosing the corresponding network in the "Select" field.
A8. After hving selected a wireless network, you must then specify the network key
of your wireless router for Security key.
After completing the entry, click on the "Apply" button. After the reboot has been
completed, the Wi-Fi Repeater is accessible under the SSID and the Wireless key of
you wireless router.
B. Configure the Wi-Fi Repeater vvith RJ45 Cable.
B1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer/ laptop with
the Wi-Fi Repeater with enclosed RJ45 Cable.
B2. Follow process A4 to A8 to configure your Wi-Fi Repeater.
08
Configure the Wireless AP Mode
Use the AP Mode to obtain a 'wireless access point" The wireless end devices will
connect to the Wi-Fi Repeater in this mode. You can also use this mode, for example,
to make a formerly non-wireless-enabled router wireless-enabled.
1. The mode selector must be set to the 'Access Point' position for AP Mode
2. Plug the Wi-Fi Repeater into a wall socket.
3. Follow process A3 to A5.
4. After logging in, you will see the web page below:
Click on the AP button in the Wizard field.
09
Indice
