GeChic M161H-R1 Manuale utente
M161H-R1 Monitor
User Manual
How-to’s
23.03.15
The sign alerts you to potential hazards that can hurt you or damage the product.
1. Use only the power supply and power cord that comes with this monitor. Using
other power adapter may cause malfunction or danger.
2. It is recommended to use the monitor in a well-ventilated environment at room
temperature around 0 to 40 and humidity around 45 to 85 . The monitor
should display continuously changing images rather than displaying the same and a
still image for a long time. If you need to use this monitor in an abnormal environ-
ment such as high temperature, high humidity, conned space, low atmospheric
pressure, etc., please contact Gechic customer service center for further advice on
usage environment.
3. When plugging in/out the cables, do make sure the force exerts in horizontal direc-
tion and do not shake the plug in vertical direction. Any damage caused by wrong
plug urging is not included in the warranty coverage.
4. Cleaning On-Lap Monitor: Unplug the power input before cleaning. Please use soft
cloth to clean touch screen. For stubborn stains, please use lightly-dampened cloth to
wipe again. Do not use benzene, alcohol, thinner, ammonia, abrasive cleaners, com-
pressed air or other corrosive solvents. These solvents may cause permanent dam-
age on the screen or leave unremovable stain.
5. Do not expose the LCD panel to sunlight.
6. The product is not waterproof. Do not use this product in or near water.
7. Do not use the volume that may cause damage to hearing; when connecting head-
phones to use, please lower the volume setting rst. Slowly adjust to the appropriate
volume, do not wear headphones for long, continuous, high volume to avoid hearing
damage.
8. Overuse of the monitor may result in vision damage. For every 30 minutes with the
monitor, give your eyes 10 minutes break. Avoid children under aged 2 watching the
monitor; prevent children over aged 2 from watching with the monitor over 1 hour per
day.
9.Exclusions from Warranty Service
Please read the warranty terms below carefully, and follow the usage guide and
precautionary notes. Please keep this manual for future reference. GeChic does not
warrant uninterrupted or error-free operation of this Product. The warranty only
covers failure /malfunction under normal use conditions during warranty period. The
warranty does not apply to the following conditions:
(1)The bar code has been removed or worn down, and cannot be identied.
(2)This product has been modied, disassembled, or retted.
(3)Display and touch function working normally; only variation in appearance (e.g., age-
ing, attrition, scratch, color changing and etc.).
(4)Any breakdown caused by power supply. (e.g., inputting power over rating voltage or
unsteady current)
(5)Any damage caused by disoperation or failure to follow this manual. (e.g., Plug or
unplug cables in wrong direction and causing damage on cables or the monitor.)
(6)Any damage caused by hitting or cracking monitor accidentally or purposely, or col-
lapsing or overturning monitor.
°C°C%%
◆
◆
Under the Partition
HDMI-A Video Cable
USB-A to USB-C Power Cable
5V 2A Adapter
Sleeve(16A4)
USB Type-C Video Cable
◆
Optional Accessory Description
M1S4 Stand Insert the quick-release port of M16 monitor into M1S4
stand and you can use the monitor above the laptop.
M16 VESA 75 Aluminum
Alloy Bracket
With 4 VESA 75 screw holes and a 1/4” screw hole for
screwing M16 monitor on a VESA arm, mounting on the
wall or installing on the camera cradle head of tripod.
USB Type-C Video
Cable (2M)
Connect one end to computer's USB-C (DP Alt) port,
and the other end to M16's USB-C port to transmit
audio, video signals and power at the same time.
HDMI-A to mini-HDMI
Video Cable (2.1 M)
Connect mini-HDMI plug to camera and connect HDMI-
A plug to M16 monitor.
LED Power Indicator
It shows green light when the monitor is "On" and shows red
light when the monitor is stands by. There is no light when
the monitor is "O".
Power
Press once to turn on the monitor and press again to turn
o the monitor.
Reset: Press and hold for 5 seconds to reset the OSD set-
tings to default.
Exit/ Input Source
Press this button to show "Input Source" and then press
to switch the input sources. When using the OSD menu,
press this button to return to previous page.
Menu/ Select
Press this button to launch OSD panel. When using OSD
menu, press this button to select and enter the next page.
Increase Volume/ Up or Left
Press this button to show ”Volume bar”. Press and hold this
button to increase the Volume continuously. In the OSD
menu, press this button to move up or the left.
Decrease Volume/ Down or Right
Press this button to show ”Volume bar”. Press and hold this
button to decrease the Volume continuously. In the OSD
menu, press this button to move down or the right.
+ OSD Menu Unlock
Press these two buttons at the same time to release ”OSD
Menu Lock” and enable the functions of OSD buttons.
As shown in the g., use GeChic USB Type-C video cable (optional) to con-
nect the monitor's USB-C port to the computer's USB Type-C(DP Alt) port.
The computer outputs power and video signals through its USB Type-C
port, so there is no need to connect the power adapter and HDMI cable. To
output audio, please connect headphones or speakers to the headphone
out jack of the monitor.
Notice! The USB Type-C ports on the computer or phone must:
1. support DisplayPort Alternate Mode (USB Type-C(DP Alt Mode)).
2. be able to stably output 5V 2.0A current to the monitor (if the phone cannot
supply sucient current, please connect the adapter to DC IN port of the
monitor.)
The Gechic label is on the FRONT of the sleeve, which is the thick side to
protect the screen panel. Please put the thick side of the sleeve up, put the
monitor into the sleeve with the panel upward, and then stick the hook and
loop tape.
Caution! DO NOT put the monitor into the sleeve with its panel side toward
the back of sleeve. The panel side must face the thick side of the sleeve to
protect the panel from being broken.
Caution! Do not put items on the sleeve or hit the sleeve vigorously, other-
wise the screen panel will be broken.
Thick Side
Slim Side
Panel Side
As shown in the g., use USB-A to USB-C power cable to connect the moni-
tor's DC IN port to 5V 2A adapter (or two USB-A ports of the computer) and
connect monitor's HDMI input port to the computer by HDMI-A video cable,
game console or other devices. When you need to output audio, please con-
nect headphones or speakers to the headphone out jack of the monitor.
To 5V 2A Power
WARNING ! Please use the HDMI-A cable
included in this product in priority.
The top side of the HDMI-A plug shell must be
less than 3mm thick, otherwise it will put pres-
sure and cause malfunction on the monitor.
Use the M16 VESA 75 Aluminum Alloy Bracket (optional) to secure M161H
monitor to a monitor arm, wall mount or T1S2 Stand (optional). As shown in
the g., please follow below assembly steps :
○
1Use two M4 screws to screw the M16 VESA 75 Aluminum Alloy Bracket to
the screw holes on the back of the monitor.
○
2Use four M4 screws to screw M16 monitor to the monitor arm, wall mount
or T1S2 stand.
Monitor Arm
T1S2 Stand
1/4” Screw Hole
◆
As shown in the Fig., enter "Display Settings"
to adjust "Brightness", "Contrast",
"Sharpness", etc.
1. ECO Mode: The maximum brightness is at
50 in ECO Mode.
2. Auto Adjust: Launch "Auto Contrast Adjust"
and "Auto Brightness Adjust" to adjust
brightness and contrast automatically to
ensure the highest quality when displaying moving images.
3. Aspect Ratio: When "Full Screen(16:9)" is selected, the monitor displays a
16:9 image in full screen. When "4:3" is selected, the monitor displays a 4:3
image with left-right side black borders to ll the 16:9 screen. When
"Original" is selected, the monitor displays
the image in its original size.
◆
1. Color Eect: If the output format of com-
puter image is RGB Limited, it is recom-
mended to select "Standard1"; if it is RGB
Full format, it is recommended to select
"Standard2". Select "Dark Highlight" mode
to brighten up dark areas; select "Text"
mode to make HTML text clearer.
2. Blue Light Reduction: Select "On" to reduce
the screen's blue light automatically.
3. Color Temperature: Select "Cool" to in-
crease the blue color of the image; Select
"Warm" to increase the red color of the
image. Select "User" to adjust the RGB
color settings manually.
◆
1. Auto Power O: Select "Yes" to activate
this function. When there is no image input,
the monitor will enter Standby mode, and
power o itself after 270 seconds. The
power button shall be pressed to turn on
the monitor again. Select "No" to disable
this function. The monitor will remain in
standby mode and will not switch o the
power.
Indice
Altri manuali GeChic Monitor
GeChic
GeChic On-Lap 2501 Series Manuale utente
GeChic
GeChic On-Lap 1502 Manuale utente
GeChic
GeChic OnLap 1302 Manuale utente
GeChic
GeChic On-Lap M505E Manuale utente
GeChic
GeChic On-Lap 1305H-B Manuale utente
GeChic
GeChic On-Lap 1302 Manuale utente
GeChic
GeChic On-Lap 1002 Manuale utente
GeChic
GeChic On-Lap 1305H Manuale utente
GeChic
GeChic On-Lap 2101H Manuale utente
GeChic
GeChic On-Lap M505E Manuale utente
